for selecting unit). Instead, use the resource hints mechanism.
One unfortunate situation here is that there is no resource_quad_value
function- which is what I needed for WWN boot time replacement. Worse-
you can't store the hint as just plain
hint.isp.0.nodewwn="0x50000000aaaa0001"
because this gets interpreted as an int- incorrectly because it can't
be converted to an int. I can't even get this as a string. To work
around this particular case for nodewwn && portwwn setting, this
rather grotesque form will be used:
hint.isp.0.nodewwn="w50000000aaaa0001"
hint.isp.0.portwwn="w50000000aaaa0002"
At the same time, if we have no hinted WWN, set the default WWN (which, btw,
gets overridden if the card has valid NVRAM, which is usual) to
0x400000007F000009ull (which translates to NAA == IPv4, 127.0.0.9).
Eliminate more printf's and replace them either with device_printf or
isp_prt calls.
ones where we have a CAM path) and replacing them with calls to isp_prt.,
Eliminate isp_unit references- we no longer have an isp_unit- we now
have an isp_dev that device_get_unit can work with.
`rootvnode' pointer, but vfs_syscalls.c's checkdirs() assumed that
it did. This bug reliably caused a panic at reboot time if any
filesystem had been mounted directly over /.
The checkdirs() function is called at mount time to find any process
fd_cdir or fd_rdir pointers referencing the covered mountpoint
vnode. It transfers these to point at the root of the new filesystem.
However, this process was not reversed at unmount time, so processes
with a cwd/root at a mount point would unexpectedly lose their
cwd/root following a mount-unmount cycle at that mountpoint.
This change should fix both of the above issues. Start_init() now
holds an extra vnode reference corresponding to `rootvnode', and
dounmount() releases this reference when the root filesystem is
unmounted just before reboot. Dounmount() now undoes the actions
taken by checkdirs() at mount time; any process cdir/rdir pointers
that reference the root vnode of the unmounted filesystem are
transferred to the now-uncovered vnode.
Reviewed by: bde, phk
a regular basis. Adjust our linux emulation to conform. This will
cause more dirty pages to be left for the pagedaemon to deal with,
but our new low-memory handling code can deal with it. The linux
way appears to be a trend, and we may very well make MAP_NOSYNC the
default for FreeBSD as well (once we have reasonable sequential
write-behind heuristics for random faults).
(will be MFC'd prior to 4.3 freeze)
Suggested by: Andrew Gallatin
make sure that PG_NOSYNC is properly set. Previously we only set it
for a write-fault, but this can occur on a read-fault too.
(will be MFCd prior to 4.3 freeze)
hit on the client side and prevent the server side from retiring writes.
Pipeline operations turned off for all READs (no big loss since reads are
usually synchronous) and for NFS writes, and left on for the default bwrite().
(MFC expected prior to 4.3 freeze)
Testing by: mjacob, dillon
update native priority, it is diffcult to get right and likely
to end up horribly wrong. Use an honestly wrong fixed value
that seems to work; PUSER for user threads, and the interrupt
priority for ithreads. Set it once when the process is created
and forget about it.
Suggested by: bde
Pointy hat: me
if an arriving packet belongs to us, also check that the packet arrived
through the correct interface. Skip this check if the packet was locally
generated.
CVSrepo deletion of the previous attempt will be requested:
--original message--
Add the 'virtual nulmodem driver'
Particularly useful for debuging kernels using vmware.
If your name is Bruce evans and you are a WIZ at tty interfaces,
then you should probably rip this to shreds and offer lots of suggestions and
patches. I've been using this since 4.0-CURRENT and it's never caused
problems but I'm sure I got something wrong. This is similar to the pty/cty
device driver except that both sides are ttys. Even minor numbers
are side A and odd minor numbers are side B.
Work needs to be done regarding what happens to the other side when you
close a node.
to use with vmware, configure vmware to redirect COM2 out to side A of one
of these and boot a kernel with teh gdb remote port set to sio1.
AFTER dropping into the gdb kernel debugger in your test kernel,
fire up gdb with it's remote port pointing at the appropriate side B.
To catch all console output, you can boot the vmware kernel with a serial
console, (COM1) similarly redirected to a nulmodem, and use 'tip' to observe it.
This is practically unaltered since pre 4.0 days except for
changes made along the way needed to make it compile, so any suggestions
or offers of total rewrites will be listenned to :-)
When we recieve a fragmented TCP packet (other than the first) we can't
extract header information (we don't have state to reference). In a rather
unelegant fashion we just move on and assume a non-match.
Recent additions to the TCP header-specific section of the code neglected
to add the logic to the fragment code so in those cases the match was
assumed to be positive and those parts of the rule (which should have
resulted in a non-match/continue) were instead skipped (which means
the processing of the rule continued even though it had already not
matched).
Fault can be spread out over Rich Steenbergen (tcpoptions) and myself
(tcp{seq,ack,win}).
rwatson sent me a patch that got me thinking about this whole situation
(but what I'm committing / this description is mine so don't blame him).
rather than in silly places like "VFS Cluster debugging". People
should really be using COMPAT_LINUX instead of the linux module on
dynamic systems like -current.
process's priority go through the roof when it released a (contested)
mutex. Only set the native priority in mtx_lock if hasn't already
been set.
Reviewed by: jhb
in VMware reports 0x00000000 in the PCI subsystem ID register, but
0x10001000 when you read the mirror registers in I/O space. This causes
pcn_probe() to think it's found a card in 32-bit mode, and performing
a 32-bit I/O access makes on a 16-bit port makes VMware go boom. Special
case the 0x10001000 value until somebody at VMware grows a clue.
Finally discovered by: Andrew Gallatin
For TCP, verify that the sequence number in the ICMP packet falls within
the tcp receive window before performing any actions indicated by the
icmp packet.
Clean up some layering violations (access to tcp internals from in_pcb)
handle read and write requests for widths of multiple bytes. This
can be used to read 16-bit battery status registers for example.
- Remove some unused variables and #if 0'd debugging cruft.
- Don't complain about a GPE query that fails due to AE_NOT_FOUND if the
query method was _Q00.
from a BIF, use the size of the destinatino buffer, not the length of the
string to determine where to put the nul char. As a side effect, the
old code would truncate the string by one character while it was possibly
overflowing the buffer.
This piece of code has not been referenced since it was put there
in 1995. Also done a codebased search on popular networking libraries
and third-party applications. This is an orphan.
Reviewed by: jesper
