allow the watermark to be passed in via the data field during the EV_ADD
operation.
Hook this up to the socket read/write filters; if specified, it overrides
the so_{rcv|snd}.sb_lowat values in the filter.
Inspired by: "Ronald F. Guilmette" <rfg@monkeys.com>
the current socket error in fflags. This may be useful for determining
why a connect() request fails.
Inspired by: "Jonathan Graehl" <jonathan@graehl.org>
error will be passed up to the user, who will close the connection, so
it does not appear to make a sense to leave the connection open.
This also fixes a bug with kqueue, where the filter does not set EOF
on the connection, because the connection is still open.
Also remove calls to so{rw}wakeup, as we aren't doing anything with
them at the moment anyway.
Reviewed by: alfred, jesper
reset TCP connections which are in the SYN_SENT state, if the sequence
number in the echoed ICMP reply is correct. This behavior can be
controlled by the sysctl net.inet.tcp.icmp_may_rst.
Currently, only subtypes 2,3,10,11,12 are treated as such
(port, protocol and administrative unreachables).
Assocaiate an error code with these resets which is reported to the
user application: ENETRESET.
Disallow resetting TCP sessions which are not in a SYN_SENT state.
Reviewed by: jesper, -net
this information via the vm.nswapdev sysctl (number of swap areas)
and vm.swapdevX nodes (where X is the device), which contain the MIBs
dev, blocks, used, and flags. These changes are required to allow
top and other userland swap-monitoring utilities to run without
setgid kmem.
Submitted by: Thomas Moestl <tmoestl@gmx.net>
Reviewed by: freebsd-audit
and add a sysctl to pppoe to activate non standard ethertypes
so that idiot ISPs (apparently in France) who use
equipment from idiot suppliers (rumour says 3com)
who use nonstandard ethertypes can still connect.
"yep, sure we do pppoe, we use a different identifier to that dictated in
the standard, but sure it's pppoe!"
sysctl -w net.graph.stupid_isp=1 enables the changeover.
attached and ifconfigable. The card doesn't interrupt yet.
Also, move towards bus space by introducing new macros/inline
functions which make such a move much easier than before.
These inline functions are setup now to work around an IBM EtherJet
pccard cardbus bridge incompatibility. The card works in 8 bit mode,
but not in 16-bit mode when it is connected to a cardbus bridge for
reasons unknown. The Linux driver also has a similar workaround in
it.
Future work will include making the above workaround runtime
conditional rather than compile time conditional, as well as fixing
the interrupts in pccards and converting it to bus space.
for the ICB firmware options meant- *I* had taken it to
mean that if you set it, Node Name would be ignored and
derived from Port Name. Actually, it meant the opposite.
As a consequence- change ICBOPT_USE_PORTNAME to the
define ICBOPT_BOTH_WWNS- makes more sense.
Fix wrong input bitmap for MBOX_DUMP_RAM command. Call
ISP_DUMPREGS if we get a f/w crash. Add ISPCTL_RUN_MBOXCMD
control command (so outer layers can run a mailbox command
directly) and add a ISPASYNC_UNHANDLED_RESPONSE hook so
outer layers can understand response queue entries we
might not know about.
depend on this. The linux ABI emulator tries to use it for some linux
binaries too. VM86 had a bigger cost than this and it was made default
a while ago.
Reviewed by: jhb, imp
and 1.84 of src/sys/netinet/udp_usrreq.c
The changes broken down:
- remove 0 as a wildcard for addresses and port numbers in
src/sys/netinet/in_pcb.c:in_pcbnotify()
- add src/sys/netinet/in_pcb.c:in_pcbnotifyall() used to notify
all sessions with the specific remote address.
- change
- src/sys/netinet/udp_usrreq.c:udp_ctlinput()
- src/sys/netinet/tcp_subr.c:tcp_ctlinput()
to use in_pcbnotifyall() to notify multiple sessions, instead of
using in_pcbnotify() with 0 as src address and as port numbers.
- remove check for src port == 0 in
- src/sys/netinet/tcp_subr.c:tcp_ctlinput()
- src/sys/netinet/udp_usrreq.c:udp_ctlinput()
as they are no longer needed.
- move handling of redirects and host dead from in_pcbnotify() to
udp_ctlinput() and tcp_ctlinput(), so they will call
in_pcbnotifyall() to notify all sessions with the specific
remote address.
Approved by: jlemon
Inspired by: NetBSD
interrupts.
Protect usage of the per processor switchtime variable against
interrupts in calcru().
This seem to eliminate the "microuptime() went backwards" warnings.
the the original trapframe of the syscall, trap, or interrupt that entered
the kernel. Before SMPng, ast's were handled via a psuedo trap at the
end of doerti. With the SMPng commit, ast's were broken out into a
separate ast() function that was called from doreti to match the behavior
of other architectures. Unfortunately, when this was done, the
p_md.md_regs member of curproc was not updateda in ast(), thus when
signals are handled by userret() after an interrupt that returns to
userland, we end up using a stale trapframe that will result in the
registers from the old trapframe overwriting the real trapframe and
smashing all the registers right before we return to usermode. The saved
%cs:%eip from where we were in usermode are saved in the trapframe for
example.
- Don't use an atomic operation to update cnt.v_soft in ast(). This is
the only place the variable is written to, and sched_lock is always
held when it is written, so it is already protected and the mutex release
of sched_lock asserts a memory barrier that ensures the value will be
updated in a timely fashion.
packet flow into two unidirectional flows.
Part of a suite of nodes developed for packet flow control.
More to follow as I have time to port them to 5.x or
as others do so. The ipfw node will be the hardest..
Submitted by: "Vitaly V. Belekhov" <vitaly@riss-telecom.ru>
- Remove unneeded spl()'s around mi_switch() in userret().
- Don't hold sched_lock across addupc_task().
- Remove the MD function child_return() now that the MI function
fork_return() is used instead.
- Use TRAPF_USERMODE() instead of dinking with the trapframe directly to
check for ast's in kernel mode.
- Check astpending(curproc) and resched_wanted() in ast() and return if
neither is true.
- Use astoff() rather than setting the non-existent per-cpu variable
astpending to 0 to clear an ast.
- Don't hold sched_lock around addupc_task() as this apparently breaks
profiling badly due to sched_lock being held across copyin().
Reported by: bde (2)
for us.
- Change the switch_trampoline() to call fork_exit() passing in the
required arguments instead of calling the fork trampoline callout
function directly.
Warning: this hasn't been tested.
Looked over by: dfr
