- Update to firmware 1.4.39 for dual-chip NIC (10G-PCIE2-xxx)
support, and SFP+ i2c support
- Identify newer "B" NICs (10G-PCIEx-8B-x) correctly, rather than
mis-identifying them as "A" NICs (cosmetic only)
- Identify the IFM_10G_LRM ifmedia type, where applicable.
- Identify ifmedia types for SFP+ based NICs
- Update copyright
Sponsored by: Myricom
MFC after: 1 week
Deprecate unused phy_delay Self ID field as it was removed
by 1394a-2000.
Attempt to parse extended Self ID PHY packets if they are detected
Reviewed by: scottl (mentor)
MFC after: 2 weeks
interesting conditional printf's into single device_printf's
Change a couple of variable names so that I don't have to trace what they
acutally do anymore.
Enable the display of the Self ID PHY packet if firewire_debug > 0
Reviewed by: scottl(mentor)
MFC after: 2 weeks
Prior to this fix, IEVENT register was always cleared before calling
tsec_error_intr_locked(), which prevented error recovery actions from
happening with polling enabled (and could lead to serious problems, including
controller hang).
Submitted by: Marcin Ligenza marcinl ! pacomp dot com dot pl
- interrupt coalescing
- polling
- jumbo frames
- multicast
- VLAN tagging
The enhanced version of the chip (eTSEC) can also take advantage of:
- TCP/IP checksum calculation h/w offloading
Obtained from: Freescale, Semihalf
If speed of link between two devices is slower than the reported max
speed of both endpoints, the current driver will fail and be unable to
negotiate.
Summary:
Test negotiated speed by reading the CSRROM into a dummy variable.
If that read fails, decrement our speed and retry. If all else fails,
go to lowest speed possible(0).
Report speed to the user.
Add display of the Bus Info Block when debug.firewire_debug > 1
Support the Bus Info Block(1394a-2000) method of speed detection.
I also should note that I am moving "hold_count" to 0 for future
releases.
This variable determines how many bus resets to "hold" a removed
firewire device before deletion. I don't feel this is useful and will
probably drop support for this sysctl in the future.
Reviewed by: scottl(mentor)
MFC after: 2 weeks
almost once. After we've configured the devices that were present the
first time through, then we know that we're done. If the device has
other devices that are deferred, then it must do a similar dance.
This catches both PC Cards and CardBus cards.
to not allocate them after the recent ata channels enumeration changes.
It allows to save some resources, not bother user with unexisting hardware
and not check unimplemented ports status on every interrupt.
Works fine with AHCI and theoretically other MSI capable devices.
At this moment support disabled by default. To enable it, set
"hint.atapci.X.msi=1" device hint.
Add two new functions to the libusb20 API and required kernel ioctls.
- libusb20_dev_get_iface_desc
- libusb20_dev_get_info
New command to usbconfig, "show_ifdrv", which will print out the kernel driver
attached to the given USB device aswell.
See "man libusb20" for a detailed description.
Some minor style corrections long-line wrapping.
Submitted by: Hans Petter Selasky
- specification claims that 1 second is just a maximum controller reset time;
implement controller reset properly to save almost 1 second of boot, and
about half second of resume time;
- enable channel interrupts only after channel status reset to fix duplicate
device creation on resume due to unwanted device connection event;
- as described in specification, wait for disk ready status after channel
power-up; it is not so important when disk already touched by BIOS, but
solves device not ready problems on resume and probably some other cases.
- uncomment channel stop/start on soft-reset as it is declared mandatory by
specification; it was commented due to some random drive detection problems
on VIA and JMicron controllers, but I hope it is fixed by previous point.
Move channel softc initialization from ata_XXX_probe() to ata_XXX_attach().
Instead of calculating ata channel number as position in child device list,
pass it's real number directly from controller probe routine using ivars.
It is simpler and IMHO more correct.
Giving a charactere device execute permissions doesn't have any use.
Right now there isn't a single device node in /dev that has it, except
the USB2 device node, so remove it.
Approved by: hps, thompsa
longer do we require SCTP to be in the kernel for the
lib to be able to handle SCTP. We do this by moving
the CRC32c checksum into libkern/crc32.c and then adjusting
all routines to use the common methods. Note that this
will improve the performance of iSCSI since they were
using the old single 256 bit table lookup versus the
slicing 8 algorithm (which gives a 4x speed up in
CRC32c calculation :-D)
Reviewed by:rwatson, gnn, scottl, paolo
MFC after: 4 week? (assuming we MFC the alias_sctp changes)
fails to attach (possibly due to disable hints) then we get called back for
unload. Correctly handle the case where the keyboard isnt found rather than
calling panic.
- Make usb2_transfer_pending() part of the USB core header file.
- Make usb2_transfer_pending() NULL safe.
- Make sure that USB process functions return if the process has been drained.
- Remove two unused functions.
Submitted by: Hans Petter Selasky
name) (not sure whether this works correctly, but should be close).
Fix the stub attach phase for some Novatel cards. They expect the CSW
(repsonse to CBW, SCSI eject command) to be fetched before switching to
modem mode.
MFC after: 2 weeks
