guaranteed to initialize its two last arguments. Therefore, there is a
warning in the subsequent caller ar5416FillVpdTable(), which doesn't
initialize those arguments.
Change getLowerUpperIndex() to assign values to indexL and indexR even
in the case of assertion failure.
Submitted by: Pavel Roskin <proski@gnu.org>
in 'sc_state'. This allows the lpt_release_ppbus() calls in those two
routines to actually release the ppbus and thus fixes the hangs noticed
with the lpt(4) driver since the recent ppbus changes. The old lpt(4)
driver didn't actually check the HAVEBUS flag in lpt_release_ppbus() which
is why these bugs weren't noticed before.
use patches so far:
+ Envy24:
- fix: broken init data for M Audio Delta DiO 2496
- add: support for M Audio Delta 44
- add: support for M Audio Delta 1010LT
Tested by: Dominique Goncalves, dominique.goncalves at gmail.com
- add: support for Terratec EWX 2496
Tested by: Stefan Sperling, stsp at stsp.name
- add: support for M Audio Delta 66
Tested by: Richard Bown, richard.bown at blueyonder.co.uk
- add: support for M Audio Delta 1010
Tested by: Andrew Reilly, areilly at bigpond.net.au
+ Envy24HT:
- add: support for Terrasoniq TS22PCI
- fix: M-Audio Revolution 5.1 sound volume is very low
Reported by: Oliver Hartmann, ohartman at zedat.fu-berlin.de
Andrey Slusar, anrays at gmail.com
Tested by: Andrey Slusar, anrays at gmail.com
Rusu Silviu, arol.the at gmail.com
- fix: M-Audio Revolution 7.1 sound is distorted and very quiet
Reported by: Olev Hannula, hannula at gmail.com
Tested by: Olev Hannula, hannula at gmail.com
Stanislav Belansky, stanislav at icmail.ru
- fix: Terratec PHASE 22 codec is power-off due to wrong init data
Reported by: Philipp Ost, pj at smo.de
Tested by: Philipp Ost, pj at smo.de
+ SpicDS:
- fix: AK4381 produce hiss sound on 192kHz sample rate
- fix: stupid bug with volume control for AK4396
Submitted by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
MFp4 //depot/projects/usb; 157412
Sync from svn.freebsd.org/base/user/thompsa/usb which is a minimal changeset
from oldUSB (no config_td).
This excludes the taskqueue changes (for the moment) as requested.
Sync from svn.freebsd.org/base/user/thompsa/usb which is a minimal changeset
from oldUSB (no config_td).
This excludes the taskqueue changes (for the moment) as requested.
- Change "usb2_pause_mtx" so that it takes the timeout value in ticks
- Make sure that attach waits for the generic probe to leave room for firware
loader drivers and device specific USB Audio drivers like USB phone adapters
Submitted by: Hans Petter Selasky
- USB serial drivers cleanup, factor out code
- Simplify line state programming
- Integrate uslcom from old USB stack
Submitted by: Hans Petter Selasky
1. Move most of the ifnet logic into the usb2_ethernet module, this includes,
- make all usb ethernet interfaces named ue%d
- handle all threading in usb2_ethernet
- provide default ioctl handler
- handle mbuf rx
- provide locked callbacks for init,start,stop,etc
2. Cleanup CDC-Ethernet driver.
Submitted by: Hans Petter Selasky
Obtained from: svn.freebsd.org/base/user/thompsa/usb [1]
- Change "usb2_pause_mtx" so that it takes the timeout value in ticks
- Factor out USB ethernet and USB serial driver specific control request.
- USB process naming cleanup.
Submitted by: Hans Petter Selasky
- Change "usb2_pause_mtx" so that it takes the timeout value in ticks
- USB controller: EHCI High Speed Interrupt endpoint fix.
- Fix OHCI and EHCI counting bug when multiple TD's are involved in
a short USB transfer and a short packet happens on the non-last TD in the
USB transfer frame.
- USB process naming cleanup.
Submitted by: Hans Petter Selasky
controllers that lose Tx completion interrupts under certain
conditions. With this change it's safe to use MSI on PCIe
controllers so enable MSI on these controllers.
offset. This is needed for the ehci hardware buffer rings that assume
this behavior.
This is an interim solution, and a more general one is being worked
on. This solution doesn't break anything that doesn't ask for it
directly. The mbuf and uio variants with this flag likely don't work
and haven't been tested.
Universe builds with these changes. I don't have a huge-memory
machine to test these changes with, but will be happy to work with
folks that do and hps if this changes turns out not to be sufficient.
Submitted by: alfred@ from Hans Peter Selasky's original
solving a possible panic when snd_ai2s is loaded at boot time. Also change
the device setup to indicate to the pcm layer that the device is MPSAFE.
Submitted by: Marco Trillo
Suggestions by: Ariff Abdullah
- correct format strings
- fill opt_agp.h if AGP_DEBUG is defined
- bring AGP_DEBUG to LINT by mentioning it in NOTES
This should hopefully fix a warning that was...
Found by: Coverity Prevent(tm)
CID: 3676
Tested on: amd64, i386
o change tdma packet drop msg when ack required to ATH_DEBUG_TDMA
(ATH_DEBUG_XMIT is too noisy)
o add a debug msg for raw packet drop due to interface down/invalid
o add stats for these two cases
o explain how another drop case is handled
o add CFI_SUPPORT_STRATAFLASH compile option to enable support
o add new ioctls to get/set the factory and user/oem segments of the PR
and to get/set Protection Lock Register that fuses the user segment
o add #defines for bits in the status register
o update cfi_wait_ready to take an offset so it can be used to wait for
PR write completion and replace constants w/ symbolic names
Note: writing the user segment isn't correct; committing now to get review.
Sponsored by: Carlson Wireless
Reviewed by: imp, Chris Anderson
The TTY buffers used the standard <sys/queue.h> lists. Unfortunately
they have a big shortcoming. If you want to have a double linked list,
but no tail pointer, it's still not possible to obtain the previous
element in the list. Inside the buffers we don't need them. This is why
I switched to custom linked list macros. The macros will also keep track
of the amount of items in the list. Because it doesn't use a sentinel,
we can just initialize the queues with zero.
In its simplest form (the output queue), we will only keep two
references to blocks in the queue, namely the head of the list and the
last block in use. All free blocks are stored behind the last block in
use.
I noticed there was a very subtle bug in the previous code: in a very
uncommon corner case, it would uma_zfree() a block in the queue before
calling memcpy() to extract the data from the block.
