Right now the only way to force a cold reset is:
* The HAL itself detects it's needed, or
* The sysctl, setting all resets to be cold.
Trouble is, cold resets take quite a bit longer than warm resets.
However, there are situations where a cold reset would be nice.
Specifically, after a stuck beacon, BB/MAC hang, stuck calibration results,
etc.
The vendor HAL has a separate method to set the reset reason (which is
how HAL_RESET_BBPANIC gets set) which informs the HAL during the reset path
why it occured. This is almost but not quite the same; I may eventually
unify both approaches in the future.
This commit just extends HAL_RESET_TYPE to include both status (eg BBPANIC)
and type (eg do COLD.) None of the HAL code uses it yet though; that'll
come later.
It also is a big no-op in each HAL - I need to go teach each of the HALs
about cold/warm reset through this path.
Using unmapped IO is really beneficial when running inside of a VM,
since it avoids IPIs to other vCPUs in order to invalidate the
mappings.
This patch adds unmapped IO support to blkfront. The following tests
results have been obtained when running on a Xen host without HAP:
PVHVM
3165.84 real 6354.17 user 4483.32 sys
PVHVM with unmapped IO
2099.46 real 4624.52 user 2967.38 sys
This is because when running using shadow page tables TLB flushes and
range invalidations are much more expensive, so using unmapped IO
provides a very important performance boost.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
X-MFC-with: r290610
dev/xen/blkfront/blkfront.c:
- Add and announce support for unmapped IO.
The implementation of bus_dmamap_load_ma_triv currently calls
_bus_dmamap_load_phys on each page that is part of the passed in buffer.
Since each page is treated as an individual buffer, the resulting behaviour
is different from the behaviour of _bus_dmamap_load_buffer. This breaks
certain drivers, like Xen blkfront.
If an unmapped buffer of size 4096 that starts at offset 13 into the first
page is passed to the current _bus_dmamap_load_ma implementation (so the ma
array contains two pages), the result is that two segments are created, one
with a size of 4083 and the other with size 13 (because two independant
calls to _bus_dmamap_load_phys are performed, one for each physical page).
If the same is done with a mapped buffer and calling _bus_dmamap_load_buffer
the result is that only one segment is created, with a size of 4096.
This patch relegates the usage of bus_dmamap_load_ma_triv in x86 bounce
buffer code to drivers requesting BUS_DMA_KEEP_PG_OFFSET and implements
_bus_dmamap_load_ma so that it's behaviour is the same as the mapped version
(_bus_dmamap_load_buffer). This patch only modifies the x86 bounce buffer
code, other arches are left untouched.
Sponsored by: Citrix Systems R&D
Reviewed by: kib, jah (previous version)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D888
Rename arp_ifinit2() into arp_announce_ifaddr().
Eliminate zeroing ifa_rtrequest: it was used for calling arp_rtrequest()
which was responsible for handling route cloning requests. It became
obsolete since r186119 (L2/L3 split).
- Don't use contractions (don't -> do not)
- Change "throw away" to "discard" when describing the -o keep-bad-images option
- Revert author e-mail split I brought over from NetBSD, effectively reverting
the change bapt made in r267668
MFC after: 3 days
Submitted by: bjk
Sponsored by: EMC / Isilon Storage Division
as lib/libc/tests/gen
The code in test-fnmatch that was used for generating:
- bin/sh/tests/builtins/case2.0
- bin/sh/tests/builtins/case3.0
has been left undisturbed. The target `make sh-tests` has been moved over
from tools/regression/lib/libc/gen/Makefile to
lib/libc/tests/gen/Makefile and made into a PHONY target
case2.0 and case3.0 test input generation isn't being done automatically.
This needs additional discussion.
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
- Remove a leftover printf from when this was a TAP based testcase
- Catch mmap failures properly
MFC after: 3 days
Sponsored by: EMC / Isilon Storage Division
- Set BINDIR to TESTSDIR globally (and subsequently, remove all
`${FILESGROUP}DIR` setting because BINDIR is set to `TESTSDIR`)
- Set MAN to "" globally, instead of per-PROG
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
before their initial configuration is done, it turns out that r281337
has the inverse effect on some older chips. Moreover, as with newer
chips before, two chips seemingly identical according to their MAC
revisions may behave differently in this regard, with most working
but a few not, making changes extremely hard to test.
Closer inspection of the corresponding Linux code suggests that RX
and TX should only be enabled after their initial configuration with
RTL8168G and later chips, i. e. RTL8106E{,US}, RTL8107E, as well as
RTL8168{EP,G,GU,H}, so limit the new code path to these. [1]
- Distinguish between RTL8168H and RTL8107E, with the latter being the
10/100-Mbit/s-only variant of the former.
- For MAC variants that can only do Fast Ethernet at a maximum, ensure
that we don't advertise Gigabit Ethernet speed.
- In re_stop(), do the inverse of re_init_locked() and enable RXDV
gate on RTL8168G and later chips again, matching what Linux does.
PR: 203422 [1]
MFC after: 1 week
- Filter out unneeded frames in STA mode.
- Implement ic_promisc() call.
Tested with RTL8188EU, STA and MONITOR modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3999
as lib/libc/tests/net
Also, fix eui64_aton_test:test_str(..). The test was comparing the result
of eui64_aton to a pointer of the expected result.
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
learned that the Power8 and the PS3 have a mix of OFW and FDT. Both have AIM
defined. But currently they are not affected. They have no I2C devices under
OFW.
This version was tested on a Quad G5 and build tested for armv6*.
Discussed with nwhitehorn@
Reviewed by: ian@
by bus_dmamem_alloc() which creates associated bus_dmamap_t map for us.
When this memory is freed by bus_dmamem_free(), the map is freed as well.
Thus there is no need to free it explicitly by bus_dmamap_destroy(),
which leads to double freeing.
Discussed with: gonzo
Approved by: kib (mentor)
as otherwise most of the time is spent resolving UIDs to names.
Reviewed by: mjg@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D4059
the root filesystem without full reboot, using "reboot -r". This can
be used to to eg. boot from a temporary md_image preloaded by loader(8),
setup an iSCSI session, and continue booting from rootfs mounted over
iSCSI.
Reviewed by: kib@, bapt@
MFC after: 1 month
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3693
variable during mp_start() which is too late. Move this to mp_setmaxid()
where other architectures set it and move x86 assertions to MI code.
Reviewed by: kib (x86 part)
32-bits aligned. Merge the two bounce buffers into a single one. Some
rough tests showed that the DWC OTG throughput on RPI2 increased by
10% after this patch.
MFC after: 1 week
provided on amd64, but not i386. Add libm to DPADD/LDADD to unbreak the i386
tinderbox
Pointyhat to: ngie
MFC after: 1 week
X-MFC with: r290538
Sponsored by: EMC / Isilon Storage Division
as lib/libc/tests/stdlib
- Make the code a bit more style(9) compliant
- Convert a sizeof(x)/sizeof(x[0]) to nitems
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
- Emulate Linux mutex API using sx(9) locks with only exclusive operations
instead of mutex(9), in Linux mutexes are sleepable.
- Emulate Linux rwlock_t using rwlock(9) instead of sx(9). rwlock_t
in Linux are spin locks
is non-zero.
- Include the process address in the PROC_ASSERT_HELD() and
PROC_ASSERT_NOT_HELD() assertion messages so that the corresponding
process can be found easily when debugging.
MFC after: 1 week
