FPU registers for copying. Remove the switch table and jumps from
bcopy/bzero/... to the actual implementation.
As a side-effect, i486-optimized bzero is removed.
Reviewed by: bde
Tested by: pho (previous version)
properly short terminate their transfers. This fixes a problem where input
appears several seconds late.
Reported by: Alexander Yerenkow
Submitted by: Hans Petter Selasky
HPET to steal IRQ0 from i8254 and IRQ8 from RTC timers. It can be suitable
for HPETs without FSB interrupts support, as it gives them two unshared
IRQs. It allows them to provide one per-CPU event timer on dual-CPU system,
that should be suitable for further tickless kernels.
To enable it, such lines may be added to /boot/loader.conf:
hint.atrtc.0.clock=0
hint.attimer.0.clock=0
hint.hpet.0.legacy_route=1
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
measured interval as upper bound. It should be more precise then just
assuming hz/2. For idle CPU it should be quite precise, for busy - not
worse then before.
state lower than the lowest one supported by the current CPU. This closes
some races with changes to the hw.acpi.cpu_cx_lowest sysctl while Cx
states for individual CPUs were changing (e.g. unplugging the AC adapter
of a laptop) that could result in panics.
Submitted by: Giovanni Trematerra
Tested by: David Demelier demelier dot david of gmail
MFC after: 3 days
Although the sysctls are marked with CTLFLAG_RD and the values will stay
immutable, current sysctl implementation stores value pointer in
void* type, which means that const qualifier is discarded anyway
and some newer compilers complaint about that.
We can't use de-const trick in sysctl implementation, because in that
case we could miss an opposite situation where a const value is used
with CTLFLAG_RW sysctl.
Complaint from: gcc 4.4, clang
MFC after: 2 weeks
beginning with the highest available rate. Currently we always use
54m for the first retry no matter what AMRR has choosen. Fix this
by setting the index to the next lower rate.
Approved by: rpaulo (mentor)
Tested by: Brandon Gooch <jamesbrandongooch at gmail.com>
MFC after: 2 weeks
callback function will be executed, and that the key won't be deleted during
the init process.
- txmic and rxmic are written into the chip the same place regardless of
opmode.
- Make the hardware generate 802.11 sequence numbers.
Submitted by: Akinori Furukoshi
Obtained from: git://gitorious.org/run/run.git
The following systems are involved:
- DB-88F5182
- DB-88F5281
- DB-88F6281
- DB-78100
- SheevaPlug
This overhaul covers the following major changes:
- All integrated peripherals drivers for Marvell ARM SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- Since the common FDT infrastrucutre (fdtbus, simplebus) is used we say
good by to obio / mbus drivers and numerous hard-coded config data.
Note that world needs to be built WITH_FDT for the affected platforms.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation.
The T3 ASIC can provide an incoming packet's timestamp instead of its RSS hash.
The timestamp is just a counter running off the card's clock. With a 175MHz
clock an increment represents ~5.7ns and the 32 bit value wraps around in ~25s.
# sysctl -d dev.cxgbc.0.pkt_timestamp
dev.cxgbc.0.pkt_timestamp: provide packet timestamp instead of connection hash
# sysctl -d dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: core clock frequency (in KHz)
# sysctl dev.cxgbc.0.core_clock
dev.cxgbc.0.core_clock: 175000
Remove unneeded rxtx handler, make que handler generic.
Do not allocate header mbufs in rx ring if not doing hdr split.
Release the lock in rxeof call to stack.
MFC for 8.1 asap
via %s
Most of the cases looked harmless, but this is done for the sake of
correctness. In one case it even allowed to drop an intermediate buffer.
Found by: clang
MFC after: 2 week
