device, make sure we have no real HPET device entry with same ID.
As side effect, it potentially allows several HPETs to be attached.
Use first of them for timecounting, rest (if ever present) could later
be used as event sources.
hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
When not defining header split do not allocate mbufs,
this can be a BIG savings in the mbuf memory pool.
Also keep seperate dma maps for the header and
payload pieces when doing header split. The basis
of this code was a patch done a while ago by
yongari, thank you :)
A number of white space changes.
MFC: in a few days
free(9) and it can cause kernel panic when there are multiple graphics
controllers in the system.
Tested by: Brandon Gooch (jamesbrandongooch at gmail dot com)
MFC after: 3 days
firmware in order to take over control of the SMU. Without doing this,
the firmware background process doing fan control will run amok as we
take over the system and crash the management chip.
This is limited to these two machines because our kernel is heavily
dependent on firmware accesses, and so quiescing firmware can cause
nasty problems.
Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
so ni_txrate returned 0 which is a invalid result.
- The fourth argument of ieee80211_ratectl_tx_complete() could be not
NULL.
Reported by: Gustau P?rez <gperez at entel.upc.edu>
Tested by: Gustau P?rez <gperez at entel.upc.edu>,
Ian FREISLICH <ianf at clue.co.za>
MFC after: 3 days
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
Reported by: Richard Kolkovich
Submitted by: Hans Petter Selasky
USB enumeration lock is locked, then the USB stack fails to resume the device
because locking the USB enumeration lock is part of the resume procedure. To
solve this issue a new lock is introduced which only protects the suspend and
resume callbacks, which can be dropped inside the usbd_do_request_flags()
function, to allow suspend and resume during so-called enumeration operations.
Submitted by: Hans Petter Selasky
hardware tag insertion/stripping. Remove conditional code that
disables these hardware features on SiS190. Also nuke RX fixup code
which is no more required on strict-alignment architectures because
SiS190 supports RX 10 bytes padding.
Now all hardware features except jumbo frame and WOL are supported.
Thanks to Masa Murayama who confirmed SiS190 also has the same
hardware features of SiS191.
I guess the only difference between SiS191 and SiS190 would be
jumbo frame support. It will be implemented in near future.
fragmentation of mbuf chain to 32 from 16 because TSO can send 64KB
sized packet which in turn requires long list of mbuf chain. Due to
lack of documentation, I'm not sure whether driver have to pull up
ethernet/IP/TCP header with options to make controller work but
driver have to parse TCP header to update pseudo TCP checksum
anyway. The controller expects pseudo TCP checksum computed by
upper stack and the checksum should follow the MS NDIS
specification to make TSO work.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
fxp(4) already used to extract most hardware MAC statistics but it
didn't show them. With this change, all MAC statistics counters
are exported. Because there are a couple of new counters for 82558
and 82559, enable extended MAC statistics functionality to get
these counters. Accoring to public data sheet, 82559 MAC statistics
return 24 DWORD counters(3 counters are unknown at this moment) so
increase MAC counter structure to meet the MAC statistics block size.
The completion of MAC counter dump is now checked against
FXP_STATS_DR_COMPLETE status code which is appended at the end of
status block. Previously fxp(4) ignored the status of the
FXP_SCB_COMMAND_CU_DUMPRESET command. fxp(4) does not wait for the
completion of pending command before issuing
FXP_SCB_COMMAND_CU_DUMPRESET. Instead it skips the command and try
it next time. This scheme may show better performance but there is
chance to loose updated counters after stopping controller. So make
sure to update MAC statistics in fxp_stop().
While I'm here move sysctl node creation to fxp_sysctl_node().
Tested by: Larry Baird < lab <> gta dot com >
table. The default size of the configuration table was 22 bytes. To
use extended feature of 82550/82551 the configuration table size
was expanded to 32 bytes. The added configuration for 82550/82551
specifies VLAN hardware tagging and IPSec configuration as well as
TCO.
To make configuration easier fxp(4) used a configuration template
and the template was copied to configuration table. After that,
some parameters of the configuration table was changed depending on
controller type and operation mode. However the size of template
was 22 bytes so some configuration parameters were not properly
initialized on 82550/82551.
Fix this by increasing the template size. For 82557, 82558 and
82559 the size of the configuration is still 22 bytes.
unicast and the other for multicast. To receive multicast frames
that host didn't join in promiscuous mode, driver have to set
promiscuous mode for multicast frames as well.
The Open Source Software Developer Manual for i8255x was not clear
how to handle promiscuous mode.
PR: kern/145905
MFC after: 5 days
from passive to active scans. Basicly disable it by increasing the
amount packets to be received to an amount which can't be reached
during dwell times.
Approved by: rpaulo (mentor)
MFC after: 3 days
L2/3/4 headers and can drop or steer packets as instructed. Filtering
based on src ip, dst ip, src port, dst port, 802.1q, udp/tcp, and mac
addr is possible. Add support in cxgbtool to program these filters.
Some simple examples:
Drop all tcp/80 traffic coming from the subnet specified.
# cxgbtool cxgb2 filter 0 sip 192.168.1.0/24 dport 80 type tcp action drop
Steer all incoming UDP traffic to qset 0.
# cxgbtool cxgb2 filter 1 type udp queue 0 action pass
Steer all tcp traffic from 192.168.1.1 to qset 1.
# cxgbtool cxgb2 filter 2 sip 192.168.1.1 type tcp queue 1 action pass
Drop fragments.
# cxgbtool cxgb2 filter 3 type frag action drop
List all filters.
# cxgbtool cxgb2 filter list
index SIP DIP sport dport VLAN PRI P/MAC type Q
0 192.168.1.0/24 0.0.0.0 * 80 0 0/1 */* tcp -
1 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* udp 0
2 192.168.1.1/32 0.0.0.0 * * 0 0/1 */* tcp 1
3 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* frag -
16367 0.0.0.0/0 0.0.0.0 * * 0 0/1 */* * *
MFC after: 2 weeks
is no more need to defragment mbufs. After transmitting the
multi-fragmented frame, the controller updates only the first
descriptor of multi-descriptor transmission so it's driver's
responsibility to clear OWN bits of remaining descriptor of
multi-descriptor transmission. It seems the controller behaves much
like jme(4) controllers in descriptor handling.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
received frames. Also check driver has valid ifp pointer before
calling msk_stop() in device_shutdown handler. While I'm here
remove unnecessary accesses to interrupt mask registers in
device_shutdown handler because driver puts the controller into
reset state.
With these changes, msk(4) now survive from heavy RX traffic(1byte
UDP frame) while reboot is in progress.
Reported by: Mark Atkinson < atkin901 <> gmail dot com >
by zero of the second argument 'from'.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
Pointed out by: Andrew Reilly (areilly at bigpond dot net dot au)[1]
MFC after: 3 days
on Cassini using the external PCS SERDES otherwise unaligned access
traps and other strange effects happen with some machines. Don't touch
the MIF which is unused in that case either. These changes require the
PHY type to use to be determined via the OFW device tree or from the
VPD in machines without the former.
- Disable the SERDES pins of Saturn when not used in order to save power
and ensure they are enabled otherwise.
- In cas_attach() use the correct register offset for CAS_PCS_CONF_EN.
- Add some bus space barriers missing in the PCS code path.
These changes make the Sun GigaSwift Ethernet 1.0 MMF cards as well as
the on-board interfaces found in Sun Fire B100s Blade Server work.
PR: 144867
scope of the object lock in agp_i810.c. (In this specific case, the scope
of the object lock shouldn't matter, but I don't want to create a bad
example that might be copied to a case where it did matter.)
Reviewed by: kib
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.
- device initiated power management (some devices support only this way);
- Automatic Partial to Slumber Transition (more power saving);
- DMA auto-activation (expected to slightly improve performance).
More features could be added later, when hardware supports.
This bug would cause allocating sample-mode PMCs to fail with ENOMEM after allocating several counting-mode PMCs.
Approved by: jkoshy (mentor)
MFC after: 2 weeks
that generates a fatal bus trap. Normally, the chips are setup to do
128 byte DMA bursts, but when on this CPU, they can only safely due
4-byte DMA bursts due to this bug. Details of the exact nature of the
bug are sketchy, but some can be found at
https://forum.openwrt.org/viewtopic.php?pid=70060 on pages 4, 5 and 6.
There's a small performance penalty associated with this workaround,
so it is only enabled when needed on the Atheros AR71xx platforms.
Unfortunately, this condition is impossible to detect at runtime
without MIPS specific ifdefs. Rather than cast an overly-broad net
like Linux/OpenWRT dues (which enables this workaround all the time on
MIPS32 platforms), we put this option in the kernel for just the
affected machines. Sam didn't like this aspect of the patch when he
reviewed it, and I'd love to hear sane proposals on how to fix it :)
Reviewed by: sam@
does. Without this change, Yukon Extreme seems to generate lots of
RX FIFO overruns even though controller has available RX buffers.
These excessive RX FIFO overruns generated lots of pause frames
which in turn killed devices plugged into switch. It seems there is
still occasional RX frame corruption on Yukon Extreme but this
change seems to fix the pause frame storm.
Reported by: jhb
Tested by: jhb
MFC after: 5 days
- Print device details only when verbose boot is enabled.
- Add debug output for shared memory access.
- Add debug statistics (checksum offload & VLAN frame counters).
- Modify TX path to update consumer index for each frame completed
rather than updating the consumer index only once for a group of
frames to improve small packet performance.
- Print driver/firmware pulse messages only when verbose boot
is enabled.
- Add debug sysctl to clear statistics.
- Fix more style(9) violations.
MFC after: 2 weeks
architecture from page queue lock to a hashed array of page locks
(based on a patch by Jeff Roberson), I've implemented page lock
support in the MI code and have only moved vm_page's hold_count
out from under page queue mutex to page lock. This changes
pmap_extract_and_hold on all pmaps.
Supported by: Bitgravity Inc.
Discussed with: alc, jeffr, and kib
controller, I'm not sure whether this is also applicable to SiS190
so this feature is only activated on SiS191 controller.
In theory, controller reinitialization is not needed when VLAN tag
configuration is changed, but xclin said controller was not stable
whenever toggling VLAN tag bit. To address that, sge(4)
reinitialize controller for VLAN configuration which seems to work
as expected. VLAN tag information for TX/RX descriptor and
configure bit of RxMacControl register was found by xclin.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw > (initial version)
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
register. Due to lack of SiS190 controller, I'm not sure whether
this is also applicable to SiS190 so this feature is only activated
on SiS191 controller.
The controller can pad 10 bytes before DMAing a received frame to
RX buffer and received bytes include the padded bytes. This padding
is very useful on strict-alignment architectures because driver
does not have to copy received frame to align IP header on 4 bytes
boundary. It also gives better RX performance on non-strict
alignment architectures. Special thanks to xclin to give me
valuable register information. Without his enthusiastic trial and
errors this wouldn't be even possible.
While I'm here tighten validity check of received frame. Controller
clears RDS_CRCOK bit when it received bad CRC frames. xclin found
that using loop back testing.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
programs RX filter configuration. It seems RX MAC control register
is one of key registers to get various offloading features as well
as performance. Blindly clearing unrelated bits can result in
unexpected results.
Tested by: xclin <xclin <> cs dot nctu dot edu dot tw >
emulated by BIOS using SMI interrupt. On those chipsets reading
from the status port may be thousand times slower than usually.
Sometimes this emilation is not working properly resulting in
commands timing out and since we assume that inb() operation
takes very little time to complete we need to adjust number of
retries to keep waiting time within a designed limits (100ms).
Measure time it takes to make read_status() call and adjust
number of retries accordingly.
To keep it simple, use TSC to measure inb() performance and
keep it to amd64-only, since TSC may not available on older
CPUs.
Also enable detection of the AT controller absence on amd64.
Reviewed by: jhb
MFC after: 1 month
back in rxeof (I could see little point in taking it out),
and now release it before the stack entry.
Also, make it so the 82574 does not configure for multiqueue
when its not used in the stack.
On top of that, LLVM+Clang mis-compiles this code because of its register
allocator bug.
Analyzed by: Andrew Reilly (areilly at bigpond dot net dot au)
Reviewed by: ariff, rdivacky
MFC after: 3 days
In the end, it does help fixing /dev/io usage from multithreaded
processes.
- On i386 and amd64 the old behaviour is kept but multithreaded
processes must use the new interface in order to work well.
- Support for the other architectures is greatly improved, where
necessary, by the necessity to define very small things now.
Manpage update will happen shortly.
Sponsored by: Sandvine Incorporated
PR: threads/116181
Reviewed by: emaste, marcel
MFC after: 3 weeks
Open Firmware device tree in order to match what the PROM built-in
driver uses. This is especially important when netbooting Fujitsu
Siemens PRIMEPOWER250 as in that case the built-in driver isn't used
and the port facts PortSCSIID defaults to 0, conflicting with the
disk at the same address.
first descriptor in TSO case. Otherwise controller can generate bad
frames during TSO. To address it, make sure to pull up ethernet +
IP + TCP header with options in first buffer. Also ensure the
buffer length of the first descriptor for TSO covers entire ethernet
+ IP + TCP with options and setup additional Tx descriptor if the
first buffer includes TCP payload.
Tested by: Amar Takhar <verm <> darkbeer dot org >
MFC after: 1 week
Some of these cases should be safe in a non-atomic fashion, however
since all of the driver ioctls are locked, a lot of work is required to
fix it correctly. Just don't sleep now.
MFC after: 2 weeks
was chosen by lots of trial and errors. The chosen value shows
good interrupt moderation without additional latency.
Without this change, controller can generate more than 140k
interrupts per second under high network load.
Submitted by: xclin <xclin <> cs dot nctu dot edu dot tw >
This time, abandon the use of busdma and start interacting with the VM
system directly. Make use of the new kmem_alloc_attr() which allows us
to easily allocate non-contiguous pages to back the GART table. This
should help a lot when starting or restarting X after the system has
been running for a while and memory has become fragmented.
MFC after: 2 weeks
* On 32 bit platforms we steal the upper 4 bits of the map handle
to store a unique map id.
* On 64 bit platforms we steal the upper 24 bits.
Resolves issues where the offsets that are handed to mmap may overlap the VRAM on some cards.
Tested on: radeon, intel, mga, and via.
This will break nouveau. I will spin new patches shortly.
proper device_t so it faked the devctl event to appear like one, this is now a
notify which allows more information to be passed.
We notify for both the device attach/detach and for each usb interface. A devd
rule can now match on the interface properties, including composite devices
which may have a uvideo interface and also usound and possibly uhid too.
An example to match a umass device with a scsi subclass and BBB protocol would be
notify 100 {
match "system" "USB";
match "subsystem" "INTERFACE";
match "type" "ATTACH";
match "intclass" "0x08";
match "intsubclass" "0x06";
match "intprotocol" "0x50";
action ...
};
The old attach devctl event has been retained for the moment to make merging to
8.1 easier. This was never compatible with 7.x or earlier due to the ugen regex
change needed.
Reviewed by: warner
MFC after: 1 week
occurs. In addition, the delay when programming the short cable fix
should be 100us, not 100ms.
PR: kern/64556
Submitted by: Thomas Hurst <tom at hur.st>
Approved by: rrs (mentor)
MFC after: 1 week
no flowid is present, this was causing some bad
reordering, now just use 0.
Also, add a few watchdog bits, and tx handler bits
that were corrected in igb.
- Re-probe xfp / sfp+ socket on link events, in case user
has changed transceiver
- correctly report current media to avoid confusing lagg (reported by Panasas)
- Report link speed (submitted by yongari)
Reviewed by: yongari (earlier version)
MFC after: 7 days
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
