o Introduce new chip_type AX88790. There's a few places we need to know the
exact chip for workaronds.
o Explain the AX88190 workaround for the ISR bits being stuck, and don't
apply them to the AX88790. The datasheet says the bits are fixed, and
experience confirms.
o Fix mii bit-bang read code to read and discard the 'floating' bit.
o Remove empty ed_pccard_ax88x90_mii_reset routine
o Report error from mii_phy_probe
o Don't use ed_probe_Novel_generic for ax88x90 chips. It puts them into
an odd state sometimes. Instead, use a more stream-lined version that
avoids the trouble spots. This was copied and tweaked from the original.
o Move chip reset into its own routine.
o Minor code optimiation on getting MAC address
o Add code for coping with AX88790 cards that are in power down state and
need to be kicked before the PHY registers for the internal phy read right.
o Remove ugly cap of PHYs at 17.
o For AX88790, we need to set a special bit for accessig phy 16 (the internal
phy) and clear it for all others according to a chip erratum.
o streamline the bit-bang code for AX88x90: the delays aren't needed according
to the datasheet timing diagrams and also the Linux driver
o Fix minor bit definition for direction bit.
o Generally: Some comments reformatted
o Only try the toshiba probe on cards labelled as toshiba
# From another Akihabara card (this one from a few years ago from a
# friend in Japan). Fix the Corega FEther II PCC-TXD. This one is
# still on sale new, as of a few weeks ago. should fix all other AX88x90
# based cards, but I have some testing left to finish on my collection...
o PC98 uses 32-bit block numbers. Limit the scheme to 2^32-1
blocks when the media is larger. The 32-bit block numbers
are implicit (16-bit cylinder * 8-bit head * 8-bit sector).
o EBR uses 32-bit block numbers. Limit the scheme to 2^32-1
blocks when the media is larger.
o Calculate the number of entries based on the rounded media
size, rather than the raw media size.
in directory vnodes. Allow namecache dotdot entry to be created pointing
from child vnode to parent vnode if no existing links in opposite
direction exist. Use direct link from parent to child for dotdot lookups
otherwise.
This restores more efficient dotdot caching in NFS filesystems which
was lost when vnodes stoppped being type stable.
Reviewed by: kib
It's quite strange that nobody reported this issue before. It turns out
functions like ttyname(), ptsname() and fdevname() don't work in
compat32. This means it't not even possible to run applications like
script(1) inside a 32-bit FreeBSD jail.
Fix this by converting 32-bit fiodgname_arg structures to their 64-bit
equivalent.
Reported by: kris
Tested by: kris
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
provider namespace. These are inserted dynamically into the
VOP_..._AP() functions created from vnode_if.src. Each VOP has
entry and return probes, as arg0 the primary vnode, arg1 the
vnode operation argument structure pointer, providing access to
IN and OUT arguments, and for return probes, arg2 the return
value.
MFC after: 1 month
Sponsored by: Google, Inc.
src/sys and not the entire src/ tree.
An earlier solution by peter had been comitted in r183528 and backed out
in r183566 due to problems with newvers.sh also called from other places
during world build. With the extra test this survived a make universe.
The work have been under testing and fixing since then, and it is mature enough
to be put into HEAD for further testing.
A lot have changed in this time, and here are the most important:
- Gvinum now uses one single workerthread instead of one thread for each
volume and each plex. The reason for this is that the previous scheme was
very complex, and was the cause of many of the bugs discovered in gvinum.
Instead, gvinum now uses one worker thread with an event queue, quite
similar to what used in gmirror.
- The rebuild/grow/initialize/parity check routines no longer runs in
separate threads, but are run as regular I/O requests with special flags.
This made it easier to support mounted growing and parity rebuild.
- Support for growing striped and raid5-plexes, meaning that one can extend the
volumes for these plex types in addition to the concat type. Also works while
the volume is mounted.
- Implementation of many of the missing commands from the old vinum:
attach/detach, start (was partially implemented), stop (was partially
implemented), concat, mirror, stripe, raid5 (shortcuts for creating volumes
with one plex of these organizations).
- The parity check and rebuild no longer goes between userland/kernel, meaning
that the gvinum command will not stay and wait forever for the rebuild to
finish. You can instead watch the status with the list command.
- Many problems with gvinum have been reported since 5.x, and some has been hard
to fix due to the complicated architecture. Hopefully, it should be more
stable and better handle edge cases that previously made gvinum crash.
- Failed drives no longer disappears entirely, but now leave behind a dummy
drive that makes sure the original state is not forgotten in case the system
is rebooted between drive failures/swaps.
- Update manpage to reflect new commands and extend it with some examples.
Sponsored by: Google Summer of Code 2007
Mentored by: le
Tested by: Rick C. Petty <rick-freebsd2008 -at- kiwi-computer.com>
It seems that some revision of controller hang while accessing
the VPD. Because VPD access routine are unused, nuke it.
o Let TWSI reload EEPROM if VPD capability is detected. Reloading
EEPROM will also set ethernet address so age(4) now reads AGE_PAR0
and AGE_PAR1 register to get ethernet address. This removes a lot
of hack and enhance readability a lot.
o Double PHY reset timeout as it takes more time to take PHY out of
power-saving state.
o Explicitly check power-saving state by checking undocumented PHY
registers. If link is not up, poke undocumented registers to take
PHY out of power-saving state. This is the same way what Linux
does. On resume, make sure to wake up PHY.
o Don't rely on auto-clearing feature of master reset bit, just wait
1ms and check idle status of MAC.
o Add PCI device revision information in bootverbose mode.
This should fix occasional controller hang in device attach phase.
Reported by: barbara < barbara.xxx1975 at libero DOT it >
Tested by: barbara < barbara.xxx1975 at libero DOT it >
up) rather than amount + 1 / 2, which is the same as amount, or 2x too
many words which leads to data corruption.
# This fixes the sbdrop panics I was seeing with the Toshiba LANCT00A.
Toshiba PCETC ISA card, and even has the same board type code in the
card ID (0x14). So, for this card, call ed_probe_WD80x3_generic after
setting things up apropriately. This makes the card attach and kinda
work (I'm seeing panics in sbdrop). Since history has shown that the
WD80x3 probe routine is dangerous, only do it for this card. Also,
disable the memory range check to make sure it is an valid ISA memory.
I think that it is bogus, but I'm not 100% sure, for these cards.
I removed probing for the WD80x3 in 2005 when I added support for the
AX88x90 and DL100xx cards since none of my cards had ever matched it
and PAO3 removed it and none of the cards in their database died.
It is possible there are other quirks about this card too, since no
other open source OS supports it, or even claims to support it. But
it was a fun half hour hack...
driver. Not sure who sold it/rebadged it.
Add stub entries for Mitsubishi B8895 and Toshiba LANCT00A to the
driver with a comment that they don't work /* NG */.[*] These are
DP83902A based cards, which should work, but don't seem to. Likely
they are from the days before the ne2000 roamed the earth and use a
non-standard hookup (see if_ed_isa or if_ed_cbus for some examples).
Unless I happen to stumble into the right one, these may never work,
but I'm tired of omitting them from commits.
[*] The Japanese adopted OK from English, but also use NG for its
opposite.
typedef l_long l_off_t;
Change l_mmap_argv's to l_ulong for pgoff. This restores prior behaviour
to consumers of l_off_t but allows mmap to mmap a 32bit position which a
Linux application requires to access SMBIOS data via /dev/mem.
Reviewed by: dchagin
Prompted by: rdivacky
rather than behind a seemingly accidental constant likely left over from one of
the related drivers which uses log levels rather than per-facility debugging
flags. This should get rid of contextless messages on the console for people
who have not set (or cleared the default) debugging flags.
o Don't create an APM scheme underneath another scheme when
the probe doesn't allow it.
o APM uses 32-bit block numbers. Limit the scheme to 2^32-1
blocks when the media is larger.
packet. Linux, OpenBSD and our iwn(4) all do this. It also results in
a huge performance improvement (and the rejection of a fair number of
apparently-bad packets on receive) on my hardware.
o) Like the wpi(4) driver in OpenBSD, and like our iwn(4), also drop runt
packets.
o) Don't bother doing IFQ_POLL and then IFQ_DRV_DEQUEUE, just do
IFQ_DRV_DEQUEUE outright. This is more similar to how OpenBSD and our
iwn(4) work.
Reviewed by: sam
into acpi_cpu_startup() which is where all the other code to update this
global variable lives. This fixes a bug where cpu_cx_count was not updated
correctly if acpi_cpu_generic_cx_probe() returned early.
PR: kern/108581
Debugged by: Bruce Cran
Reviewed by: avg, njl, sepotvin
MFC after: 3 days
via the Linux tool.
- Add Linux shim to ipmi(4)
- Create a partitions file to linprocfs to make Linux fdisk see
disks. This file is dynamic so we can see disks come and go.
- Convert msdosfs to vfat in mtab since Linux uses that for
msdosfs.
- In the Linux mount path convert vfat passed in to msdosfs
so Linux mount works on FreeBSD. Note that tasting works
so that if da0 is a msdos file system
/compat/linux/bin/mount /dev/da0 /mnt
works.
- fix a 64it bug for l_off_t.
Grabing sh, mount, fdisk, df from Linux, creating a symlink of mtab to
/compat/linux/etc/mtab and then some careful unpacking of the Linux bmc
update tool and hacking makes it work on newer Dell boxes. Note, probably
if you can't figure out how to do this, then you probably shouldn't be
doing it :-)
in AMD FPUs:
- Do not clear the affected state in the case that the FPU registers for
the thread that already owns the FPU are changed via fpu_setregs(). The
only local information the thread would see is its own state in that
case.
- Fix a type mismatch for the dummy variable used in a "fld". It accepts
a float, not a double.
Reviewed by: bde
Approved by: so (cperciva)
MFC after: 1 month
When a vt switch occurs the irq handler is uninstalled. Interrupts
and the state tracking of what was enabled/disabled wasn't working
properly. This should resolve the reports of "slow windows" after a
vt switch, among other things. The radeon 2d driver seems to work a
bit more correctly than the Intel driver. With the Intel driver,
vblank interrupts will be enabled at system startup and will only
be disabled after an additional modeset (vt switch, dpms, randr event).
With this patch, I am able to run glxgears synced to vblank and
vt switch while it is running without ill effects.
MFC after: 3 days
- Trace non-error loads into the access cache once, not zero times or
twice.
- Sometimes attr cache loads fail due to a race, in which case they are
aborted leading to an invalidation; in this case, trace only the flush,
not a load.
MFC after: 1 month
Sponsored by: Google, Inc.
the requested PCI bus falls outside of the bus range given in the ACPI
MCFG table. Several BIOSes seem to not include all of the PCI busses in
systems in their MCFG tables. It maybe that the BIOS is simply buggy and
does support all the busses, but it is more conservative to just fall back
to the old method unless it is certain that memory accesses will work.
events are:
nfsclient:accesscache:flush:done
nfsclient:accesscache:get:hit
nfsclient:accesscache:get:miss
nfsclient:accesscache:load:done
They pass the vnode, uid, and requested or loaded access mode (if any);
the load event may also report a load error if the RPC fails.
The attribute cache events are:
nfsclient:attrcache:flush:done
nfsclient:attrcache:get:hit
nfsclient:attrcache:get:miss
nfsclient:attrcache:load:done
They pass the vnode, optionally the vattr if one is present (hit or load),
and in the case of a load event, also a possible RPC error.
MFC after: 1 month
Sponsored by: Google, Inc.
- Call acpi_resync_clock() to reset system time before hardclock is ready
to tick. Note we assume the current timecounter hardware and RTC are
already available for read operation.
Tested by: mav
It was derived from i386 version long ago but never resync'ed again.
Originally, i386 version compared the current time from realtime clock
with time_second (which was just `time' in the old days). When this MI
version was written, it was wrongly compared against `base' AND never
used because of a bug (typo?) in the code. This check was killed
in i386 version when home-rolled calendaric calculation was removed.
Now, we just remove the code here as well to make the code simpler.
prevent individual transactions from crossing a 4GB address boundary. Due
to bus_size_t type limitations, the driver uses a 2GB boundary in PAE
kernels.
Reviewed by: scottl
MFC after: 1 week
quirk requiring it to be enabled even when using MSI. This makes
the latter work again after r189285.
- Remove a comment which no longer applies since r190194.
filtering handle this. Introduce a new function msk_rxfilter that
handles Rx filter configuration and multicast setup as well as
promiscuous mode. This simplifies code a lot.
Promiscuous mode always have preference to any other Rx
filtering so don't disable the mode when ALLMULTI is set.
to the devctl notification queue. Empty strings cause devctl read
call to return 0 and result in devd exiting prematurely.
The actual offender (ugen notes for root hubs) will be fixed
by separate commit.
Limit the size of malloced buffer when dumping environment
variables. [EN-09:01]
Approved by: so (cperciva)
Approved by: re (kensmith)
Security: FreeBSD-SA-09:06.ktimer
Errata: FreeBSD-EN-09:01.kenv
provider. The NFS client exposes 'start' and 'done' probes for NFSv2
and NFSv3 RPCs when using the new RPC implementation, passing in the
vnode, mbuf chain, credential, and NFSv2 or NFSv3 procedure number.
For 'done' probes, the error number is also available.
Probes are named in the following way:
...
nfsclient:nfs2:write:start
nfsclient:nfs2:write:done
...
nfsclient:nfs3:access:start
nfsclient:nfs3:access:done
...
Access to the unmarshalled arguments is not easily available at this
point in the stack, but the passed probe arguments are sufficient to
to a lot of interesting things in practice. Technically, these probes
may cover multiple RPC retransmits, and even transactions if the
transaction ID change as a result of authentication failure or a
jukebox error from the server, but usefully capture the intent of a
single NFS request, such as access, getattr, write, etc.
Typical use might involve profiling RPC latency by system call, number
of RPCs, how often a getattr leads to a call to access, when failed
access control checks occur, etc. More detailed RPC information might
best be provided by adding a krpc provider. It would also be useful
to add NFS client probes for events such as the access cache or
attribute cache satisfying requests without an RPC.
Sponsored by: Google, Inc.
MFC after: 1 month
Badly formed ELF note may cause the caclulated pointer to the next note
to point both after the note region, that was checked in the code, but
also to point before the region, that was not checked [1]. Remember the
first note location in note0 and leap out if the note is not between
note0 and note_end.
In the similar way, badly formed note may cause infinite loop by
pointing next note into the same or previous note. Guard against this by
limiting amount of loop iterations by arbitrary choosen big number.
For clarity, check the calculated note alignment in each iteration.
Reported by: Chris Palmer <chris noncombatant org> [1]
PR: kern/132886
Reviewed and tested by: dchagin
MFC after: 3 days
it is right for only a tiny fraction of these devices and this
wild-card entry is too broad.
# I run a kernel without this entry at all without ill effects...
stored in the pmap is from the direct map region. The two exceptions have
been the kernel pmap and the swapper's pmap. These pmaps have used a
kernel virtual address established by pmap_bootstrap() for their shared
pml4 page table page. However, there is no reason not to use the direct
map for these pmaps as well.
they were passed uninitialized to in6_pcblookup_hash. Instead, do as is done
for IPv4 and use the addresses within the sockaddr structure, which are
correctly populated.
This fixes tcpdrop(8) for IPv6 address pairs.
Reviewed by: bz
definitely doing an NFSv2 or NFSv3 RPC, rather than sometimes doing
so and sometimes not. This makes it easier to add a DTrace return
probe at a single point in the function.
MFC after: 1 week
The tick routine was not being restarted in the init_locked routine
which could resulted in loss of carrier when updating the MTU.
Submitted by: Navdeep Parhar at Chelsio
MFC after: 3 weeks
- If boot verbose, print asicrev, chiprev and bus type on attach.
- For PCI Express devices:
1) Adjust max read request size to 4Kbytes
2) Turn on FIFO_LONG_BURST in RDMA during bge_blockinit()
Though 1) does not seem to have much to do with the poor TX performance
observed on PCI Express bge(4), 2) does fix the problem. [1]
- Nuke the RX CPU self-diag, which prevents working cards from working
(Linux tg3 does not have this diag neither does OpenBSD's bge(4)).
The increasing of the firmware handshaking timeout to 20000 retries
done as part of the original commit isn't merged as way already have a
way higher BGE_TIMEOUT of 100000.
PR: 119361 [1]
Obtained from: tg3 via DragonflyBSD [1], DragonflyBSD
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
The number of entries in the cache defaults to 8 but is easily changed in
nfsclient/nfs.h. When the cache is filled, the oldest cache entry is
evicted when space is needed.
I mirrored the changes to the NFSv[23] client in the NFSv4 client to fix
compile breakage. However, the NFSv4 client doesn't actually use the
access cache currently.
Submitted by: rmacklem
- Move tunable defines into usb_core.h and dependancy towards usb_defs.h
- Leave hardcoded defines in "usb_defs.h".
- Allow overriding all tunable defines.
- Add more customisable typedefs.
- Correct maximum device number.
Submitted by: Hans Petter Selasky
It seems I didn't fix this issue before committing teken to the tree. My
initial idea was to somehow add an error mechanism to instruct the video
driver author to increase T_NUMCOL when using very big terminals. It
turns out we have platforms where we have gigantic consoles on systems
like the Apple PowerMac G5, which means we crash there right now.
Just ignore tabstops placed beyond column 160. Just force tabs to be
placed on each 8 columns.
Reported by: nwhitehorn
handle the ioctl. There are other paths that already call it, but this
allows for a non-interface socket (like AF_LOCAL which ifconfig now
uses) to use a broader class of interface ioctls.
Approved by: bz (mentor), rwatson
supported with these pseudo-PHYs. The MIIF_NOLOOP flag currently triggers
nothing but hopefully will be respected by mii_phy_setmedia() later on.
- Don't add IFM_NONE as isolation isn't supported by these pseudo-PHYs.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
supported burst sizes.
- Add support for 64-bit burst sizes (required for SBus GEM).
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Disable rerun of the streaming cache as workaround for a silicon bug
of certain Psycho versions.
- Remove the comment regarding lack of newbus'ified bus_dma(9) as being
able to associate a DMA tag with a device would allow to implement
CDMA flushing/syncing in bus_dmamap_sync(9) but that would totally
kill performance. Given that for devices not behind a PCI-PCI bridge
the host-to-PCI bridges also only do CDMA flushing/syncing based on
interrupts there's no additional disadvantage for polling(4) callbacks
in the case schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.
- Don't panic if the power failure, power management or over-temperature
interrupts doesn't exist as these aren't mandatory and not available
with all controllers (not even Psychos). [1]
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
PR: 131371 [1]
- Hook up the streaming buffer (not used by iommu(4) by default, yet)
if available and usable. [1]
- Move the message regarding belated registration as interrupt control
under bootverbose as this isn't something the user should worry about.
Tested by: Michael Moll [1]
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
"raw" names. While there, change the formatting of extended MSDOS partitions
so that the dot (".") is not used to separate two numbers (which kind of
looks like the whole is a decimal number). Use "+" instead, which also
hints that the second part of the name is the offset from the start of
the partition in the first part of the name. Also change the offset from
decimal to hexadecimal notation, simply for aesthetic reasons and future
compatibility.
GEOM_PART is the default in 8-CURRENT but not yet in 7-STABLE so this
changeset can be MFC-ed without causing major problems from the second
part.
Reviewed by: marcel
Approved by: gnn (mentor)
MFC after: 2 weeks
after vt switch or suspend. I can't really test this on Intel right now
but I think I've heard reports of it on radeon as well. I can't break
it on the radeon here.
MFC after: 3 days
This is purely a forwarding plane cleanup; no control plane
code is involved.
Summary:
* Split IPv4 and IPv6 MROUTING support. The static compile-time
kernel option remains the same, however, the modules may now
be built for IPv4 and IPv6 separately as ip_mroute_mod and
ip6_mroute_mod.
* Clean up the IPv4 multicast forwarding code to use BSD queue
and hash table constructs. Don't build our own timer abstractions
when ratecheck() and timevalclear() etc will do.
* Expose the multicast forwarding cache (MFC) and virtual interface
table (VIF) as sysctls, to reduce netstat's dependence on libkvm
for this information for running kernels.
* bandwidth meters however still require libkvm.
* Make the MFC hash table size a boot/load-time tunable ULONG,
net.inet.ip.mfchashsize (defaults to 256).
* Remove unused members from struct vif and struct mfc.
* Kill RSVP support, as no current RSVP implementation uses it.
These stubs could be moved to raw_ip.c.
* Don't share locks or initialization between IPv4 and IPv6.
* Don't use a static struct route_in6 in ip6_mroute.c.
The v6 code is still using a cached struct route_in6, this is
moved to mif6 for the time being.
* More cleanup remains to be merged from ip_mroute.c to ip6_mroute.c.
v4 path tested using ports/net/mcast-tools.
v6 changes are mostly mechanical locking and *have not* been tested.
As these changes partially break some kernel ABIs, they will not
be MFCed. There is a lot more work to be done here.
Reviewed by: Pavlin Radoslavov
o break out version-related code to simplify rev'ing the protocol
o add parameter validation macros so checks that appear multiple places
are consistent (and easy to change)
o add protocol version check when looking for a scan candidate
o improve scan debug output format
o rewrite beacon update handling to calculate a bitmask of changed values
and pass that down through the driver callback so drivers can optimize work
o do slot bounds check before use when parsing received beacons
directory for a znode. When the directory already exists, it returns a
referenced but unlocked vnode. When a directory does not yet exist, it
calls zfs_make_xattrdir() to create a new one. zfs_make_xattrdir() returns
the vnode both referenced and and locked and zfs_get_xattrdir() was leaking
this vnode lock to its callers. Fix this by dropping the vnode lock if
zfs_make_xattrdir() successfully creates a new extended attribute
directory.
Reviewed by: pjd
or URB_FUNCTION_CLASS_xxx with HAL preemption lock that means it's
non-sleepable during USB requests though usb2_do_request() requires a
sleep so it needs to send queries to the default pipe without those
interfaces to avoid sleep.
whatever the IRP flag is because some drivers (eg. RTL8187L NDIS driver)
call IoCompleteRequest() without setting flags. It will prevent waiting
a event forever at attach.
B_DELWRI cleanup and vnode disassociation should happen just before to
assign the buffer to a queue.
Reported by: miwi, Volker <volker at vwsoft dot com>,
Ben Kaduk <minimarmot at gmail dot com>,
Christopher Mallon <christoph dot mallon at gmx dot de>
Tested by: lulf, miwi
any IPv4 multicast operations which reference it.
There is a potential race because ifma_protospec is set to NULL
when we discover the underlying ifnet has gone away. This write
is not covered by the IF_ADDR_LOCK, and it's difficult to widen
its scope without making it a recursive lock. It isn't clear why
this manifests more quickly with 802.11 interfaces, but does not
seem to manifest at all with wired interfaces.
With this change, the 802.11 related panics reported by sam@
and cokane@ should go away. It is not the right fix, that requires
more thought before 8.0.
Idea from: sam
Tested by: cokane
Obtained from: Hideotshi Shimokawa
This update is based on comments from Hidetoshi.
Changeset 183550 removed the call to crom_load() in fw_busreset(). Restore
that call such that the Configuration ROM is valid.
Stash and update fwdev settings in fw_explore_node() so that negotiation
works again.
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
This fixes osrel fetching from the FreeBSD branding note for the 64bit
platforms.
Reported by: swell.k gmail com
Reviewed by: dchagin
Tested by: dchagin, swell.k gmail com
no-op's that I inadvertently added. Even if locking is needed in general
for the ioctl's, setting a single long will not need it due to the operation
being atomic.
Reported by: rwatson
Fix regression issue in the USB file system interface.
- Use cdev_privdata pointer as indicator of correct file handle.
- Remove redundant FIFO opened flags.
Don't send ZLP at close for ulpt and uscanner devices as this causes some
models to stop working. This reverts back to the USB1 behaviour.
Submitted by: Hans Petter Selasky
This code is heavily inspired by Takanori Watanabe's experimental SMP patch
for i386 and large portion was shamelessly cut and pasted from Peter Wemm's
AP boot code.
1. fix nointr check in intsmb_start, matters only if ENABLE_ALART is
defined (by default, it is not);
2. drop unnecessary inspection/reporting of power-management io registers
base address;
3. in verbose mode report errors from SMBus host controller and their
mapping to smbus(4) errors;
Approved by: jhb (mentor)
implement CD input in hardware, while unconditional showing it confuse users.
Also it was made in the way that sometimes improper with present driver.
Add patch for ALC268 based Acer TM5320 to make headphones jack sensing work.
Default configuration defines two separate playback associations, which
current driver unable to trace properly due to order they are defined and
limited codec uniformity.
Submitted by: G. Mirov <g.mirov AT gmail.com>
the "nbufkv" sleep.
First, ffs background cg group block write requests a new buffer for
the shadow copy. When ffs_bufwrite() is called from the bufdaemon due
to buffers shortage, requesting the buffer deadlock bufdaemon.
Introduce a new flag for getnewbuf(), GB_NOWAIT_BD, to request getblk
to not block while allocating the buffer, and return failure
instead. Add a flag argument to the geteblk to allow to pass the flags
to getblk(). Do not repeat the getnewbuf() call from geteblk if buffer
allocation failed and either GB_NOWAIT_BD is specified, or geteblk()
is called from bufdaemon (or its helper, see below). In
ffs_bufwrite(), fall back to synchronous cg block write if shadow
block allocation failed.
Since r107847, buffer write assumes that vnode owning the buffer is
locked. The second problem is that buffer cache may accumulate many
buffers belonging to limited number of vnodes. With such workload,
quite often threads that own the mentioned vnodes locks are trying to
read another block from the vnodes, and, due to buffer cache
exhaustion, are asking bufdaemon for help. Bufdaemon is unable to make
any substantial progress because the vnodes are locked.
Allow the threads owning vnode locks to help the bufdaemon by doing
the flush pass over the buffer cache before getnewbuf() is going to
uninterruptible sleep. Move the flushing code from buf_daemon() to new
helper function buf_do_flush(), that is called from getnewbuf(). The
number of buffers flushed by single call to buf_do_flush() from
getnewbuf() is limited by new sysctl vfs.flushbufqtarget. Prevent
recursive calls to buf_do_flush() by marking the bufdaemon and threads
that temporarily help bufdaemon by TDP_BUFNEED flag.
In collaboration with: pho
Reviewed by: tegge (previous version)
Tested by: glebius, yandex ...
MFC after: 3 weeks
LO_CSUM_FEATURES - a bitmask of supported transmit offload features, which
will be stored in if_hwassist if IFCAP_TXCSUM is enabled, and be cleared
from mbuf packet header csum flags on transmit. (1)
LO_CSUM_SET - a bitmask of supported receive offload features, which will
be set on the mbuf packet header csum flags on transmit if IFCAP_RXCSUM
is enabled.
While here, fix SCTP offload for loopback: offer generation on the
transmit side, don't just skip validation on the receive side.
Obtained from: DragonflyBSD (1)
MFC after: 1 week
