c is assigned 0 and *loc is pointing to NULL, so c!=0 cannot be true,
and dereferencing loc would be a bad idea anyway.
Coverity Prevent: CID 5113
Reviewed by: jilles
a 2GHz channel with appropriate flags set to sc->config. Due to not zeroing
sc->config for auth/assoc those flags are still set while trying to connect
on a 5GHz channel.
MFC after: 3 days
and powerpc64 to universe for the first time. In general, provide
(slightly hacky) knowledge of multi-architecture TARGETs to universe as
well as the ability to distinguish the correct toolchain for a given
kernel using config -m.
Use pci_enable_busmaster instead of setting PCIM_CMD_BUSMASTEREN
directly. There's no need to set PCIM_CMD_MEMEN. The bit is set when a
SYS_RES_MEMORY resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Write 1 byte instead of 4 when setting the HIFN_TRDY_TIMEOUT register.
It is only 1 byte according to the specification.
Reviewed by: jhb
Approved by: kib (mentor)
configuration registers directly.
Remove pci_enable_io calls where they are redundant. The PCI bus driver
will set the right bits when the corresponding bus resource is activated.
Remove redundant pci_* function calls from suspend/resume methods. The
bus driver already saves and restores the PCI configuration.
Reviewed by: jhb
Approved by: kib (mentor)
"Use strlcpy, not strncpy, when the desired semantics are strlcpy's
rather than strncpy's."
Note: NetBSD's 1.32 is their adoption of our r216206
Obtained from: dholland@NetBSD.org
experimental NFSv4 server. The first was a bogus use of VOP_ISLOCKED()
in a KASSERT() and the second was the need to lock the vnode for the
nfsrv_checkremove() call. Also, delete a "__unused" that was bogus,
since the argument is used.
Reviewed by: zack.kirsch at isilon.com
MFC after: 2 weeks
In this case we call target function only on a single CPU and do not
need any synchronization at the setup stage.
It's a bit non-obvious but setup function of NULL means that
smp_rendezvous_cpus waits for all CPUs to arrive at the rendezvous
point, but without doing any actual setup. While using
smp_no_rendevous_barrier means that each CPU proceeds on its own
schedule without any synchronization whatsoever.
MFC after: 3 weeks
earlier commit. While here, move the thread lock down in rtp_to_pri().
It is not needed for all of the priority value checks and the computation
of newpri.
Reported by: swell.k @ gmail
MFC after: 3 days
This is based on the patch submitted by Yuri Skripachov.
Overview of the changes:
- clarify double-use of some ACPI_BATT_STAT_* definitions
- clean up undefined/extended status bits returned by _BST
- warn about charging+discharging bits being set at the same time
PR: kern/124744
Submitted by: Yuri Skripachov <y.skripachov@gmail.com>
Tested by: Yuri Skripachov <y.skripachov@gmail.com>
MFC after: 2 weeks
The CTLESC byte to protect a special character was output before instead of
after a newline directly preceding the special character.
The special handling of newlines is because command substitutions discard
all trailing newlines.
allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.
delete the IRQ resource from the psmcpnp device completely.
- Don't allocate the IRQ resource shared. It is not a shareable interrupt
on ISA. The bus driver can set RF_SHAREABLE if the IRQ is actually
shareable on a non-ISA bus.
- Avoid side-effect assignments in if statements when possible.
- Don't use ! to check for NULL pointers, explicitly check against NULL.
- Explicitly check error return values against 0.
- Don't use INTR_MPSAFE for interrupt handlers with only filters as it is
meaningless.
- Remove unneeded function casts.
dlclose() call may unload the object of the outer call prematurely
because objects are unreferenced before _fini() calls.
Fix this by unreferencing objects after calling objlist_call_fini() in
dlclose(). Therefore objlist_call_fini() now calls the fini function if
the reference count of an object is 1. In addition we must restart the
list_fini traversal after every _fini() call because another dlclose()
call might have modified the reference counts.
Add an XXX comment to objlist_call_fini() about possible race with
dlopen().
PR: 133246, 149464
Reviewed by: kan, kib
