destroy operation until the referenced clone device has
been closed by the process properly. The behavior is now
consistently with the previous release.
Reviewed by: Kip Macy
event from mii(4) may not be delivered if valid link was already
established. To address the issue, check current link state after
driving MII_TICK. This should fix a regression introduced in
r184245.
PR: kern/129647
event from mii(4) may not be delivered if valid link was already
established. To address the issue, check current link state after
driving MII_TICK. This should fix a regression introduced in
r185753 on fast ethernet controllers.
Reported by: csjp, Bruce Cran < bruce <> cran DOT org DOT uk >
Tested by: csjp, Bruce Cran (initial version)
In r185891 I removed the newlines from messages written to /dev/console,
because it made startup messages from rc-scripts harder to read. This,
unfortunately, causes the kernel message that is printed after a
non-terminated log message to be concatenated.
This could be fixed, but on short term it's better to just revert the
change.
Reported by: Jaakko Heinonen <jh saunalahti fi>
Inside ptsdrv_{in,out}wakeup() we call KNOTE_LOCKED() to wake up any
kevent(2) users. Because the kqueue handlers are executed synchronously,
we must set PTS_FINISHED before calling ptsdrv_{in,out}wakeup().
Discovered by: nork
Right now the wchan strings "ttyinp" and "ttybgw" only differ one
character from the strings we used prior to MPSAFE TTY. Just rename them
back to their pre-MPSAFE TTY counterparts.
Also rename "ttylck" to "ttymtx", which should make it more clear that a
process is blocked on the TTY mutex, not some other form of locking.
o add support for IXP435 cpu's (e.g. 64 irq's)
o add support for Cambria-specific devices: npe, led's (front panel and
octal latch), ehci, mcu, ide cf
o redo memory mapping for xscale/ixp4xx boards: previously memory
was assumed aliased to 0x10000000 but this appears to be true only
for ixp425 systems and breaks operation on others; rework so memory
is assumed to start at 0
o rework NPE configuration support to use NPE id's instead of port #'s;
these changes also rename the associated MAC's to follow the NPE's
they are attached to
o update npe firmware to latest rev (same license) and update default fw
imageid's to match; in particular this adds NPE-A and crypto support
o re-style NPE fw handling code and add a console msg identifying the
attributes of the loaded fw
o fix numerous problems with handling failures during npe setup
o fix npe rx q setup; need to spin waiting for mailbox responses during
early boot stages as qmgr interrupts are not delivered; this fixes
the problem where all 8 traffic classifications were not tied to the
rx q (and eliminates the console msg "remember to fix rx q setup")
o add DELAY to npe MII wait logic for IXP435
o strip down builtin phys->virt address translation table in resource
handling to just those resources that require it and add a console msg
to alert people when this (kludge) table needs to be extended
o purge a bunch of dead netbsd-ism's
o cleanup avila led driver
o add Cambria support to boot2 and rework code for better multi-board support
Notes:
1. NPE-A doesn't work and causes NPE-C to stop working; it is disabled
in the hints
2. USB isn't working yet; controller communicates ok but device
discovery fails
3. Cambria support must be configured separately from IXP425 boards;
multi-board support is TBD
Sponsored by: Hobnob, Gateworks (board donation)
Reviewed by: imp
o add support to byte swap EHCI descriptor contents; the IXP435
has dual-EHCI controllers integral but descriptor contents are
in big-endian format; this support is configured with the
USB_EHCI_BIG_ENDIAN_DESC option and enabled with EHCI_SCFLG_BIGEDESC
o clean up EHCI USBMODE register setup during init; add #defines for
bit values
o split debug support out into a new file and enable use through ddb
o while here remove a bunch of lingering netbsd-isms
Reviewed by: imp
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
For example, ^C (SIGINT) may leave the drive spinning and locked.
This may also happen if you try to write a too-large image to a disc
and burncd(8) exits with an I/O error.
Add signal handling by doing a CDRIOCFLUSH ioctl to attempt to leave
burner in a sane state when burning is interrupted with SIGHUP, SIGINT,
SIGTERM, or in case an I/O error occurs during write.
Note, that blanking will still continue after interrupt but it seems to
finish correctly even after burncd(8) has quit.
Also, while I'm here bump WARNS to "6".
PR: 48730
Submitted by: Jaakko Heinonen <jh@saunalahti.fi>
This commit is slightly different from the original patch in the PR:
1. EM_ALPHA keeps the old value for compatibility reason.
2. Non-standard SHT_NUM is not added.
3. Style.
PR: kern/118540
Submitted by: "Pedro F. Giffuni" <giffunip[at]tutopia.com>
owned by the current user. If kinfo_getfile() or kinfo_getvmmap() return
NULL, simply exit, and do not try and derefernce the memory.
Reviewed by: peter
Approved by: peter
install a p2p host route between the end points. The ppp module
upates this router based on user configuration later on. The
rt_Update() seems to always set the RTF_GATEWAY flag, which is
broken.
Intel 855 chips present the same pci id for both heads. This prevents
us from attaching to the dummy second head. All other chips that I
am aware of either only present a single pci id, or different ids
for each head so that we only match on the correct head.
Approved by: kib@
MFC after: 2 weeks
