- Rename rt2560_read_eeprom to rt2560_read_config, we already have
rt2560_eeprom_read
- If hardware gives us wrong encryption done index, shout out loudly and
terminate the processing loop
- Process encryption done if RX done bit is set in interrupt status register
(according to Ralink Linux driver)
- Turn VALID/BUSY bits in TX descriptor only after TX descriptor is fully setup
- Fix BBP read: RT2560_BBPCSR can't be written until its RT2560_BBP_BUSY bit is
off (according to Ralink Linux driver)
- Skip invalid (0 of 0xffff) BBP register/value entries stored in EEPROM
- Fix channel TX power location in EEPROM, if channel TX power is above 31 set
it to 24 (TX power only has 5bits in RF register, "24" is according to Ralink
Linux driver)
- Configure BBP according to the BBP register/value stored in EEPROM, restore
BBP17 (RX sensitivity tuning) to default value after this.
- Set TX/RX antenna after BBP is initialized; these two operation will try to
set BBP registers
- Reconfigure ACK TX time registers according to 802.11g standard (TX @36Mb,
other side's ACK should be sent @24Mb).
- 2560 parts have two TX ring: one for management/control packets, one for data
packets. Add private OACTIVE flag for each of them. Turn on IFF_DRV_OACTIVE
if one of private OACTIVE is on; turn off IFF_DRV_OACTIVE iff all of them are
off.
- Rework watchdog to mimic old if_watchdog action. Process TX done/encryption
done in watchdog function (according to Ralink Linux driver)
Obtained from: DragonFly
Approved by: sam (mentor)
Tested by: sam
Related to PR: kern/117655
# Forcing long slot time setting is not included in this commit, comment and
# related code is in place, so if problem pops up, quick tests could be done.
down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
o conversion to callout(9) API.
o add a missing driver lock in bfe_ifmedia_sts().
o use our callout to drive watchdog timer.
o restart Tx routine if pending queued packets are present in
watchdog handler.
o unarm watchdog timer only if there are no queued packets.
o don't blindly reset phy and let phy driver handle link change
request in bfe_init_locked().
o return the status of mii_mediachg() to caller in
bfe_ifmedia_upd(). Previously it always returned 0 to caller.
o add check for IFF_DRV_RUNNING flag as well as IFF_DRV_OACTIVE
in bfe_start_locked().
o implement miibus_statchg method that keeps track of current
link state changes as well as negotiated speed/duplex/
flow-control configuration.
Reprogram MAC to appropriate duplex state. Flow-control
configuration was also implemented but commented out at the
moment. The flow-control configuration will be enabled again
after we have general flow-control framework in mii layer.
Reported by: Yousif Hassan < yousif () alumni ! jmu ! edu >
Tesdted by: Yousif Hassan < yousif () alumni ! jmu ! edu >
- Fix whitespace according to style(9).
- Sync the comment describing why we have to wait in nsphy_reset()
with nsphyter_reset(). It's true that the manual tells to not do a
reset within 500us of applying power but that's unlikely the cause
of problems seen here. Generally having to wait 500us after a reset
however is.
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.
PR: 112654
Obtained from: NetBSD
MFC after: 2 weeks
Thanks to: mlaier for testing w/ DP83815
- Remove the "thread" argument from the lockmgr() function as it is
always curthread now
- Axe lockcount() function as it is no longer used
- Axe LOCKMGR_ASSERT() as it is bogus really and no currently used.
Hopefully this will be soonly replaced by something suitable for it.
- Remove the prototype for dumplockinfo() as the function is no longer
present
Addictionally:
- Introduce a KASSERT() in lockstatus() in order to let it accept only
curthread or NULL as they should only be passed
- Do a little bit of style(9) cleanup on lockmgr.h
KPI results heavilly broken by this change, so manpages and
FreeBSD_version will be modified accordingly by further commits.
Tested by: matteo
- Improve error handling for load operations.
- Fix a memory corruption bug when using certain linux management apps.
- Allocate all commands up front to avoid OOM deadlocks later on.
checksum offoload by downloading AIC-6915 firmware. Changes are
o Header file cleanup.
o Simplified probe logic.
o s/u_int{8,16,32}_t/uint{8,16,32}_t/g
o K&R -> ANSI C.
o In register access function, added support both memory mapped and
IO space register acccess. The function will dynamically detect
which method would be choosed.
o sf_setperf() was modified to support strict-alignment
architectures.
o Use SF_MII_DATAPORT instead of hardcoded value 0xffff.
o Added link state/speed, duplex changes handling task q. The task q
is also responsible for flow control settings.
o Always hornor link up/down state reported by mii layers. The link
state information is used in sf_start() to determine whether we
got a valid link.
o Added experimental flow-control setup. It was commented out but
will be activated once we have flow-cotrol infrastructure in mii
layer.
o Simplify IFF_UP/IFCAP_POLLING and IFF_PROMISC handling logic. Rx
filter always honors promiscuous mode.
o Implemented suspend/resume methods.
o Reorganized Rx filter routine so promiscuous mode changes doesn't
require interface re-initialization.
o Reimplemnted driver probe routine such that it looks for matching
device from supported hardware list table. This change will help to
add newer hardware revision to the driver.
o Use ETHER_ADDR_LEN instead of hardcoded value.
o Prefer memory space register mapping over I/O space as the hardware
requires lots of register access to get various consumer/producer
index. Failing to get memory space mapping, sf(4) falls back to I/O
space mapping. Use of memory space register mapping requires
somewhat large memory space(512K), though.
o Switch to simpler bus_{read,write}_{1,2,4}.
o Use PCIR_BAR macro to get BARs.
o Program PCI cache line size if the cache line size was set to 0
and enable PCI MWI.
o Add a new sysctl node 'dev.sf.N.stats' that shows various MAC
counters for Rx/Tx statistics.
o Add a sysctl node to configure interrupt moderation timer. The
timer defers interrupts generation until time specified in timer
control register is expired. The value in the timer register is in
units of 102.4us. The allowable range for the timer is 0 - 31
(0 ~ 3.276ms).
The default value is 1(102.4us). Users can change the timer value
with dev.sf.N.int_mod sysctl(8) variable/loader(8) tunable.
o bus_dma(9) conversion
- Enable 64bit DMA addressing.
- Enable 64bit descriptor format support.
- Apply descriptor ring alignment requirements(256 bytes alignment).
- Apply Rx buffer address alignment requirements(4 bytes alignment).
- Apply 4GB boundary restrictions(Tx/Rx ring and its completion ring
should live in the same 4GB address space.)
- Set number of allowable number of DMA segments to 16. In fact,
AIC-6915 doesn't have a limit for number of DMA segments but it
would be waste of Tx descriptor resource if we allow more than 16.
- Rx/Tx side bus_dmamap_load_mbuf_sg(9) support.
- Added alignment fixup code for strict-alignment architectures.
- Added endianness support code in Tx/Rx descriptor access.
With these changes sf(4) should work on all platforms.
o Don't set if_mtu in device attach, it's handled in ether_ifattach.
o Use our own callout to drive watchdog timer.
o Enable VLAN oversized frames and announce sf(4)'s VLAN capability
to upper layer.
o In sf_detach(), remove mtx_initialized KASSERT as it's not possible
to get there without initialzing the mutex. Also mark that we're
about to detaching so active bpf listeners do not panic the system.
o To reduce PCI register access cycles, Rx completion ring is
directly scanned instead of reading consumer/producer index
registers. In theory, Tx completion ring also can be directly
scanned. However the completion ring is composed of two types
completion(1 for Tx done and 1 and DMA done). So reading producer
index via register access would be more safer way to detect the
ring wrap-around.
o In sf_rxeof(), don't use m_devget(9) to align recevied frames. The
alignment is required only for strict-alignment architectures and
now the alignment is handled by sf_fixup_rx() if required. The
removal of the copy operation in fast path should increase Rx
performance a lot on non-strict-alignemnt architectures such as
i386 and amd64.
o In sf_newbuf(), don't set descriptor valid bit as sf(4) is
programmed to run with normal mode. In normal mode, the valid bit
have no meaning. The valid bit should be used only when the
hardware uses polling(prefetch) mode. The end of descriptor queue
bit could be used if needed, but sf(4) relys on auto-wrapping of
hardware on 256 descriptor queue entries so both valid and
descriptor end bit are not used anymore.
o Don't disable generation of Tx DMA completion as said in datasheet
and use the Tx DMA completion entry instead of relying on Tx done
completion entry. Also added additional Tx completion entry type
check in Tx completion handler.
o Don't blindly reset watchdog timer in sf_txeof(). sf(4) now unarm
the the watchdog only if there are no active Tx descriptors in Tx
queue.
o Don't manually update various counters in driver, instead, use
built-in MAC statistic registers to update them. The statistic
registers are updated in every second.
o Modified Tx underrun handlers to increase the threshold value
in units of 256 bytes. Previously it used to increase 16 bytes
at a time which seems to take too long to stabalize whenever Tx
underrun occurrs.
o In interrupt handler, additional check for the interrupt is
performed such that interrupts only for this device is allowed to
process descriptor rings. Because reading SF_ISR register clears
all interrtups, nuke writing to a SF_ISR register.
o Tx underrun is abonormal condition and SF_ISR_ABNORMALINTR includes
the interrupt. So there is no need to inspect the Tx underrun again
in main interrupt loop.
o Don't blindly reinitialize hardware for abnormal interrupt
condition. sf(4) reintializes the hardware only when it encounters
DMA error which requires an explicit hardware reinitialization.
o Fix a long standing bug that incorrectly clears MAC statistic
registers in sf_init_locked.
o Added strict-alignment safe way of ethernet address reprogramming
as IF_LLADDR may return unaligned address.
o Move sf_reset() to sf_init_locked in order to always reset the
hardware to a known state prior to configuring hardware.
o Set default Rx DMA, Tx DMA paramters as shown in datasheet.
o Enable PCI busmaster logic and autopadding for VLAN frames.
o Rework sf_encap.
- Previously sf(4) used to type 0 of Tx descriptor with padding
enabled to store driver private data. Emebedding private data
structures into descriptors is bad idea as the structure size
would be different between 64bit and 32bit architectures. The
type 0 descriptor allows fixed number of DMA segments in
a descriptor format and provides relatively simple interface to
manage multi-fragmented frames.
However, it wastes lots of Tx descriptors as not all frames are
fragmented as the number of allowable segments in a descriptor.
- To overcome the limitation of type 0 descriptor, switch to type
2 descriptor which allows 64bit DMA addressing and can handle
unliumited number of fragmented DMA segments. The drawback of
type 2 descriptor is in its complexity in managing descriptors
as driver should handle the end of Tx ring manually.
- Manually set Tx desciptor queue end mark and record number of
used descriptors to reclaim used descriptors in sf_txeof().
o Rework sf_start.
- Honor link up/down state before attempting transmission.
- Because sf(4) uses only one of two Tx queues, use low priority
queue instead of high one. This will remove one shift operation
in each Tx kick command.
- Cache last produder index into softc such that subsequenet Tx
operation doesn't need to access producer index register.
o Rewrote sf_stats_update to include all available MAC statistic
counters.
o Employ AIC-6915 firmware from Adaptec and implement firmware
download routine and TCP/UDP checksum offload.
Partial checksum offload support was commented out due to the
possibility of firmware bug in RxGFP.
The firmware can strip VLAN tag in Rx path but the lack of firmware
assistance of VLAN tag insertion in transmit side made it useless
on FreeBSD. Unlike checksum offload, FreeBSD requires both Tx/Rx
hardware VLAN assistance capability. The firmware may also detect
wakeup frame and can wake system up from states other than D0.
However, the lack of wakeup support form D3cold state keep me from
adding WOL capability. Also detecting WOL frame requires firmware
support but it's not yet known to me whether the firmware can
process the WOL frame.
o Changed *_ADDR_HIADDR to *_ADDR_HI to match other definitions of
registers.
o Added definitioan to interrupt moderation related constants.
o Redefined SF_INTRS to include Tx DMA done and DMA errors. Removed
Tx done as it's not needed anymore.
o Added definition for Rx/Tx DMA high priority threshold.
o Nuked unused marco SF_IDX_LO, SF_IDX_HI.
o Added complete MAC statistic register definition.
o Modified sf_stats structure to hold all MAC statistic regiters.
o Nuke various driver private padding data in Tx/Rx descriptor
definition. sf(4) no longer requires private padding. Also remove
unused padding related definitions. This greatly simplifies
descriptor manipulation on 64bit architectures.
o Becase we no longer pad driver private data into descriptor,
remove deprecated/not-applicable comments for padding.
o Redefine Rx/Tx desciptor status. sf(4) doesn't use bit fileds
anymore to support endianness.
Tested by: bruffer (initial version)
be wrong but I couldn't find a way to make it work. In addition, the
number of TxGFP instruction does not match the firmware image size,
so I guess something was wrong when Adaptec generated the TxGFP
firmware from their DDK.
According to datasheet, normally, the first GFP instruction would be
opcode C, WaitForStartOfFrame, to synchronize checksumming with
incoming frame. But the first instruction in TxGFP firmware was
opcode 1, BrToImmIfTrue, so it could not process checksum correctly,
I guess. Checking for RxGFP firmware also indicates the first
instruction should be opcode C. Since the number of instructions in
TxGFP firmware lacks exactly one instruction, I prepended the opcode
C to TxGFP firmware image. With this change, the resulting image size
perfectly matches with the nummber of instructions and Tx checksum
offload seems to work without problems.
since the the command and data that is being built to be sent to or read
from the HW lives in the softc. Commands are later run via an_setdef etc.
In the ioctl path various references are kept to the data stored in
the softc so it needs to be protected. Almost think of the command
in the softc a global variable since it essentially is. Since locking
wasn't done in this type of context the commands would get corrupted.
Thanks to avatar@ for catching some lock issues and dhw@ for testing.
Things are a lot more stable except for the MPI-350 cards. My an(4)
remote laptop stays on the network now.
The driver should be changed so that it uses private memory that is passed
to the functions that talk to the card. Then only those functions would
really need to grab locks.
Reviewed by: avatar@
shortest possible chain of mbufs of m_defrag(9). What we want is
chains of mbufs that can be safely stored to a Tx descriptor which
can have up to STGE_MAXTXSEGS mbufs. The ethernet controller does
not need to align Tx buffers on 32bit boundary. So the use of
m_defrag(9) was waste of time.
problems when the DRM driver is loaded and the AIXGL extension is loaded
, the AIXGL driver requests a drm_close and this will cause the radeon
driver to fail while starting X windows.
PR: kern/114688
Submitted by: vehemens <vehemens at verizon dot net>
Prodded by: Robert Noland
Approved by: imp (mentor, a while ago already), anholt
MFC After: 1 week
- Track packet zone mbufs separately from other mbufs
- free packet zone buffers via m_free rather than trying to manage the refcount
as with clusters - its refcount and management seems to be "special"
but reread it from the device_t every time the device list is fetched.
Previously the device name in pciconf -l would not be updated when a driver
was unloaded or if a device was detached and attached to a different
driver.
MFC after: 1 week
PR: kern/104777
Submitted by: "Iasen Kostoff" tbyte | otel net
queues (which we call slices). The NIC will steer traffic into up to
hw.mxge.max_slices different receive rings based on a configurable
hash type (hw.mxge.rss_hash_type).
Currently the driver defaults to using a single slice, so the default
behavior is unchanged. Also, transmit from non-zero slices is
disabled currently.
