rather than the whole beacon interval.
The reference driver and Linux ath9k both choose 80% of the
beacon interval and they do it in the driver rather than
the HAL (Ath reference) or ath9k_hw (ath9k.)
This quietens stuck beacon conditions on my AR9220/AR9280
based NICs when a lot of burst broadcast/multicast traffic
is going on. It doesn't seem to annoy the earlier MACs as
much as the AR9280 and later one.
Obtained from: Linux ath9k, Atheros
local variable with a beacon interval of 100 TU. This never gets modified
if the beacon interval configuration changes.
This may have been correct in earlier times, but with the advent of
staggered beacons (which default to 1 / ATH_BCBUF beacon interval, so
25 TU here) this value is incorrect.
It is used to configure the default CABQ readytime. So here, the cabq
was being configured to be much greater than the target beacon timer
(TBTT.)
The driver should be configuring a cabq readytime value rather then
leaving it to the HAL to choose sensible defaults. This should be
done in the future - I'm simply trying to ensure sensible defaults
are chosen.
1. Allow the caller to select active mode.
2. Fix the envar logic so it *always* overrides the caller's flags.
3. Document the change from active to passive.
reads eating 100% CPU. Fix this by skipping select on STDIN after
reading EOF -- permanently if STDIN is not terminal and for one second
if it is.
Also after reading EOF from STDIN we have to pass it to the program
being scripted. The previous approach was to write zero bytes into the
pseudo-terminal. This does not work because zero-byte write does not
have any effect on read. Fix this by sending VEOF instead.
Submitted by: Ronald Klop <ronald-freebsd8@klop.yi.org>
Discussed with: kib, Chris Torek <chris.torek@gmail.com>
Approved by: kib
MFC after: 1 week
whle tracking down the system hang reported in kern/160662 and
corrected in revision 225806. The LOR is not the cause of the system
hang and indeed cannot cause an actual deadlock. However, it can
be easily eliminated by defering the acquisition of a buflock until
after all the vnode locks have been acquired.
Reported by: Hans Ottevanger
PR: kern/160662
but the use of fseek() means fetch(1) can't correctly resume a transfer
that was interrupted past the 2 GB mark.
Pointed out by: ache@
MFC after: 3 weeks
in append mode. Open it in read-write mode instead. Also move the
fseek up one level to cover the (unlikely but not impossible) case where
the server accepts ranges but does not send a Content-Size header.
PR: bin/117277
MFC after: 3 weeks
When a status pointer is passed in mfi_dcmd_command does not return an
errno (if the ioctl is successful), so move the test for NO_HW_PRESENT
outside of the error case. This should fix incorrect reporting for
systems with a dead or no battery.
Additionally, handle error codes other than NO_HW_PRESENT by omitting
the battery capacity display. LSI's supercap-based parts (CV series)
report their data using the same interface as battery-based parts,
except that they do not include the capacity stats (state of charge,
cumulative charge cycles, etc.)
Reviewd by: jhb, bz
Tested by: pluknet@, Garrett Cooper
PR: bin/160581
MFC after: 1 week
wdog_kern_pat() acquires eventhandler mutex, thus it cannot work in
kernel context (from where kdb_trap() runs).
The right way to fix this is both offering the
cpu-stop-on-panic-and-skip-locking logic and also a context for KDB
to officially run. We can re-enable this (or a similar) improvement
when these 2 patches hit the tree.
Sponsored by: Sandvine Incorporated
Discussed with: emaste, rstone
MFC after: immediately
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
syscall exit path. Otherwise, if SIGTRAP is ignored, that tdsendsignal()
do not want to deliver the signal, and debugger never get a notification
of exec.
Found and tested by: Anton Yuzhaninov <citrin citrin ru>
Discussed with: jhb
MFC after: 2 weeks
kerberos libraries were not linked properly (missing dependencies),
which causes 3rd party applications linking to fail when --as-needed
ld flag is used. I also added the --no-undefined ld(1) flag to make
sure that there're no missing dependencies.
MFC after: 3 days
back-end features.
sys/dev/xen/netfront/netfront.c:
o Add xn_query_features() which reads the XenStore and
records the TSO, LRO, and chained ring-request support
of the backend.
o Rename xn_configure_lro() to xn_configure_features() and
use this routine to manage the setup of TSO, LRO, and
checksum offload.
o In create_netdev(), initialize if_capabilities and
if_hwassist to the capabilities found on all backends.
Delegate configuration of if_capenable and the TSO flag
if if_hwassist to xn_configure_features().
Reported by: Hugo Silva (fix inspired by patch provided)
Approved by: re
MFC after: 1 week
PV devices with the ioemu attribute set.
sys/dev/xen/netfront/netfront.c:
o If a mac address for the interface cannot be found
in the front-side XenStore tree, look for an entry
in the back-side tree. With ioemu devices, the
emulator does not populate the front side tree and
neither does Xend.
o Return an error rather than panic when an attach
attempt fails.
Reported by: Janne Snabb (fix inspired by patch provided)
PR: kern/154302
Approved by: re
Sponsored by: BQ Internet
sys/dev/xen/netfront/netfront.c:
o Implement netfront_suspend(), a specialized suspend
handler for the netfront driver. This routine simply
disables the carrier so the driver is idle during
system suspend processing.
o Fix a leak when re-initializing LRO during a link reset.
o In netif_release_tx_bufs(), when cleaning up the grant
references for our TX ring, use gnttab_end_foreign_access_ref
instead of attempting to grant the page again.
o In netif_release_tx_bufs(), we do not track mbufs associated
with mbuf chains, but instead just free each mbuf directly.
Use m_free(), not m_freem(), to avoid double frees of mbufs.
o Refactor some code to enhance clarity.
Approved by: re
MFC after: 1 week
sys/dev/xen/control/control.c:
Fix locking violations in Xen HVM suspend processing
and have it perform similar actions to those performed
during an ACPI triggered suspend.
Sponsored by: BQ Internet
Approved by: re
MFC after: 1 week
Sponsored by: BQ Internet
sys/dev/xen/blkfront/block.h:
sys/dev/xen/blkfront/blkfront.c:
Remove now unused blkif_vdev_t from the blkfront soft.
sys/dev/xen/blkfront/blkfront.c:
o In blkfront_suspend(), indicate the desire to suspend
by changing the softc connected state to SUSPENDED, and
then wait for any I/O pending on the remote peer to
drain. Cancel suspend processing if I/O does not
drain within 30 seconds.
o Enable and update blkfront_resume(). Since I/O is
drained prior to the suspension of the VM, the complicated
recovery process performed by other Xen blkfront
implementations is avoided. We simply tear down the
connection to our old peer, and then re-connect.
o In blkif_initialize(), fix a resource leak and botched
return if we cannot allocate shadow memory for our
requests.
o In blkfront_backend_changed(), correct our response to
the XenbusStateInitialised state. This state indicates
that our backend peer has published sufficient data for
blkfront to publish ring information and other XenStore
data, not that a connection can occur. Blkfront now
will only perform connection processing in response to
the XenbusStateConnected state. This corrects an issue
where blkfront connected before the backend was ready
during resume processing.
Approved by: re
MFC after: 1 week
framework.
Sponsored by: BQ Internet
sys/xen/xenbus/xenbusb.c:
o In xenbusb_resume(), publish the state transition of the
resuming device into XenbusStateIntiailising so that the
remote peer can see it. Recording the state locally is
not sufficient to trigger a re-connect sequence.
o In xenbusb_resume(), defer new-bus resume processing until
after the remote peer's XenStore address has been updated.
The drivers may need to refer to this information during
resume processing.
sys/xen/xenbus/xenbusb_back.c:
sys/xen/xenbus/xenbusb_front.c:
Register xenbusb_resume() rather than bus_generic_resume()
as the handler for device_resume events.
sys/xen/xenstore/xenstore.c:
o Fix grammer in a comment.
o In xs_suspend(), pass suspend events on to the child
devices (e.g. xenbusb_front/back, that are attached
to the XenStore.
Approved by: re
MFC after: 1 week
executable) after r190885. The whole region for the dso is mmaped with
MAP_NOCORE flag, doing only mprotect(2) over .bss prevented it from
writing .bss to core files.
Revert the optimization of using mprotect(2) to establish .bss, overlap
the section with mmap(2).
Reported by: attilio
Reviewed by: attilio, emaste
Approved by: re (bz)
MFC after: 2 weeks
This change fixes a race in device side mode during clear-stall from
host, which can cause data to be sent too early on the given
endpoint.
Approved by: re (kib)
MFC after: 1 week
