down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
ipsec*_set_policy and do the privilege check only if needed.
Try to assimilate both ip*_ctloutput code blocks calling ipsec*_set_policy.
Reviewed by: rwatson
find | sort. As a bonus, this simplifies the logic considerably. Also
remove the bogus "overruning the args to ls" comment and the corresponding
"-n 20" argument to xargs; the whole point with xargs is precisely that it
knows how large the argument list can safely get.
Note that the first run of the updated script may hypotheticall produce
false positives due to differences between find's and sort's sorting
algorithm. I haven't seen this during testing, but others might.
MFC after: 2 weeks
a variety of bootloaders. This sometimes means that different loader
scripts are required within one ${MACHINE_ARCH}, which makes the
current practice of using ldscript.${MACHINE_ARCH} unsuitable.
Instead, make the default the current convention and allow the ld
scripts to be overridden as necessary.
If we aren't arm, pc98 or sun4v, then enable treating warnings like
errors. That doesn't mean these platforms aren't -Werror clean, just
that we haven't enforced it before. Someone with some spare time
should investigate these three platforms to see if any can be removed.
times when it shouldn't). The PR's patch has been incorporated upstream
as magic.c rev 1.46.
PR: 107676
Submitted by: Dr. Markus Waldeck <waldeck@gmx.de>
rapid wireless association changes in my experience), there is a race
where dhclient is in the process of exiting due to the link going down
when the link coming up causes devd to try and start a new one. This
results is the link being up, but no dhclient running.
Work around this race by checking a second time after a one second delay
before refusing to start a dhclient instance due to one already being
running.
MFC after: 1 week
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
- Remove redundant `s' and `S' from yesexpr.
- Add fullwidth latin letters to yesexpr and noexpr (inspired by ja_JP.UTF-8).
- Add korean translated yesexpr (`Ye') and noexpr (`Anio').
- Add yesstr and nostr entries (inspired by zh_CN.*).
- Add UTF-8 encoded file and connect to build.
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
use. If it is in use, use the watched request, otherwise use the
lockuser's own request. Only allocate a lockuser request if both
requests are null.
PR: 119920
Tested by (6.x): Landon Fuller <landonf -at- bikemonkey -dot- org>
prerequisite for using this interface. However, the 'statinfo' struct
actually references CPUSTATES from <sys/resource.h>, so in fact it
requires <sys/resource.h> to compile. Use a nested include of
<sys/resource.h> to make the code match the docs.
Reported by: Pietro Cerutti gahr | gahr.ch
aligned (or at least not cross a page boundary). However, it turns out
that on at least one machine one table header does cross a page boundary.
This caused problems with the MADT early probe as it uses the crash dump
map to load ACPI tables by loading the RSDT/XSDT into pages 1 ... N and
loading the header of each ACPI table header into page 0 looking for the
MADT. However, if a table header crossed a page boundary, then page 1
would get trashed resulting in a panic. Fix this by reserving the first
2 pages for ACPI table headers (headers are less than a page in size,
so 2 pages will be sufficient) and use pages 2 .. N for the RSDT and XSDT.
Note: amd64 should probably be simplified to just use pmap_mapbios()
for all these tables which will use the direct map and not need the
crash dump hack.
MFC after: 5 days
Tested on: i386
Reported by: Pete French petefrench of ticketswitch.com
read socket buffers in shutdown() and close():
- Call socantrcvmore() before sblock() to dislodge any threads that
might be sleeping (potentially indefinitely) while holding sblock(),
such as a thread blocked in recv().
- Flag the sblock() call as non-interruptible so that a signal
delivered to the thread calling sorflush() doesn't cause sblock() to
fail. The sblock() is required to ensure that all other socket
consumer threads have, in fact, left, and do not enter, the socket
buffer until we're done flushin it.
To implement the latter, change the 'flags' argument to sblock() to
accept two flags, SBL_WAIT and SBL_NOINTR, rather than one M_WAITOK
flag. When SBL_NOINTR is set, it forces a non-interruptible sx
acquisition, regardless of the setting of the disposition of SB_NOINTR
on the socket buffer; without this change it would be possible for
another thread to clear SB_NOINTR between when the socket buffer mutex
is released and sblock() is invoked.
Reviewed by: bz, kmacy
Reported by: Jos Backus <jos at catnook dot com>
global header if nothing else has been written before the closing of
the archive. This will change the behaviour when creating archives
without members, i.e., instead of generating a 0-size archive file, an
archive with just the global header (8 bytes in total) will be created
and it is indeed a valid archive by the definition of libarchive, thus
subsequent operation on this archive will be accepted. This especially
solves the failure caused by following sequence: (several ports do)
% ar cru libfoo.a # without specifying obj files
% ranlib libfoo.a
Reviewed by: kientzle, jkoshy
Approved by: kientzle
Approved by: jkoshy (mentor)
Reported by: erwin
MFC after: 1 month
obey or ignore the size field on a hardlink entry. In particular,
if we're reading a non-POSIX archive, we should always ignore
the size field.
This should fix both the audio/xmcd port and the math/unixstat port.
Thanks to: Pav Lucistnik for pointing these two ports out to me.
MFC after: 7 days
The only downside is that it renames pmap_vac_me_harder() to pmap_fix_cache().
From Mark's email on -arm :
pmap_get_vac_flags(), pmap_vac_me_harder(), pmap_vac_me_kpmap(), and
pmap_vac_me_user() has been rewritten as pmap_fix_cache() to be more
efficient in the kernel map case. I also removed the reference to
the md.kro_mappings, md.krw_mappings, md.uro_mappings, and md.urw_mappings
counts.
In pmap_clearbit(), we can also skip over tests and writeback/invalidations
in the PVF_MOD and PVF_REF cases if those bits are not set in the pv_flag.
PVF_WRITE will turn caching back on and remove the PV_MOD bit.
In pmap_nuke_pv(), the vm_page_flag_clear(pg, PG_WRITEABLE) has been moved
to the pmap_fix_cache().
We can be more agressive in attempting to turn caching back on by calling
pmap_fix_cache() at times that may be appropriate to turn cache on
(a kernel mapping has been removed, a write has been removed or a read
has been removed and we know the mapping does not have multiple write
mappings to a page).
In pmap_remove_pages() the cpu_idcache_wbinv_all() is moved to happen
before the page tables are NULLed because the caches are virtually
indexed and virtually tagged.
In pmap_remove_all(), the pmap_remove_write(m) is added before the
page tables are NULLed because the caches are virtually indexed and
virtually tagged. This also removes the need for the caches fixing routine
(whichever is being used pmap_vac_me_harder() or pmap_fix_cache()) to be
called on any of these mappings.
In pmap_remove(), I simplified the cache cleaning process and removed
extra TLB removals. Basically if more than PMAP_REMOVE_CLEAN_LIST_SIZE
are removed, then just flush the entire cache.
