22aeed02bf
This is a QCA9558 based design with on-chip 2GHz 3x3 11n wifi, AR8327N switch, 64MB RAM and 8MB flash. Of course, it runs FreeBSD.
150 lines
4.0 KiB
Plaintext
150 lines
4.0 KiB
Plaintext
# The TP-Link 1043NDv2 is based on the AP135 with a couple of minor
|
|
# differences - well, besides having no 11ac.
|
|
|
|
# $FreeBSD$
|
|
|
|
# QCA955X_ETH_CFG_RGMII_EN (1 << 0)
|
|
hint.qca955x_gmac.0.gmac_cfg=0x1
|
|
|
|
# mdiobus0 on arge0
|
|
hint.argemdio.0.at="nexus0"
|
|
hint.argemdio.0.maddr=0x19000000
|
|
hint.argemdio.0.msize=0x1000
|
|
hint.argemdio.0.order=0
|
|
|
|
# mdiobus1 on arge1 - required to bring up arge1?
|
|
hint.argemdio.1.at="nexus0"
|
|
hint.argemdio.1.maddr=0x1a000000
|
|
hint.argemdio.1.msize=0x1000
|
|
hint.argemdio.1.order=0
|
|
|
|
# AR8327 - connected via mdiobus0 on arge0
|
|
hint.arswitch.0.at="mdio0"
|
|
hint.arswitch.0.is_7240=0 # definitely not the internal switch!
|
|
hint.arswitch.0.is_9340=0 # not the internal switch!
|
|
hint.arswitch.0.numphys=5 # all ports are PHYs
|
|
hint.arswitch.0.phy4cpu=0
|
|
hint.arswitch.0.is_rgmii=0 # not needed
|
|
hint.arswitch.0.is_gmii=0 # not needed
|
|
|
|
# This is where it gets a bit odd. port 0 and port 6 are CPU ports.
|
|
# The current code only supports one CPU port. So hm, what should
|
|
# we do to hook PAD6 up to be RGMII but a PHY, not a MAC?
|
|
|
|
# The other trick - how do we get arge1 (hooked up to GMAC0) to work?
|
|
# That's currently supposed to be hooked up to CPU port 0.
|
|
|
|
# Other AR8327 configuration parameters
|
|
|
|
# AP136-020 parameters
|
|
|
|
# GMAC0 AR8327 -> GMAC1 (arge1) SoC, SGMII
|
|
|
|
# AR8327_PAD_MAC_SGMII
|
|
hint.arswitch.0.pad.0.mode=3
|
|
#hint.arswitch.0.pad.0.rxclk_delay_sel=0
|
|
hint.arswitch.0.pad.0.sgmii_delay_en=1
|
|
|
|
# GMAC6 AR8327 -> GMAC0 (arge0) SoC, RGMII
|
|
|
|
# AR8327_PAD_MAC_RGMII
|
|
hint.arswitch.0.pad.6.mode=6
|
|
hint.arswitch.0.pad.6.txclk_delay_en=1
|
|
hint.arswitch.0.pad.6.rxclk_delay_en=1
|
|
# AR8327_CLK_DELAY_SEL1
|
|
hint.arswitch.0.pad.6.txclk_delay_sel=1
|
|
# AR8327_CLK_DELAY_SEL2
|
|
hint.arswitch.0.pad.6.rxclk_delay_sel=2
|
|
|
|
hint.arswitch.0.led.ctrl0=0xcc35cc35
|
|
hint.arswitch.0.led.ctrl1=0xca35ca35
|
|
hint.arswitch.0.led.ctrl2=0xc935c935
|
|
hint.arswitch.0.led.ctrl3=0x03ffff00
|
|
int.arswitch.0.led.open_drain=1
|
|
|
|
# force_link=1 is required for the rest of the parameters
|
|
# to be configured.
|
|
hint.arswitch.0.port.0.force_link=1
|
|
hint.arswitch.0.port.0.speed=1000
|
|
hint.arswitch.0.port.0.duplex=1
|
|
hint.arswitch.0.port.0.txpause=1
|
|
hint.arswitch.0.port.0.rxpause=1
|
|
|
|
# force_link=1 is required for the rest of the parameters
|
|
# to be configured.
|
|
hint.arswitch.0.port.6.force_link=1
|
|
hint.arswitch.0.port.6.speed=1000
|
|
hint.arswitch.0.port.6.duplex=1
|
|
hint.arswitch.0.port.6.txpause=1
|
|
hint.arswitch.0.port.6.rxpause=1
|
|
|
|
# arge0 - hooked up to AR8327 GMAC6, RGMII
|
|
# set at 1000/full to the switch.
|
|
# so, lock both sides of this connect up to 1000/full;
|
|
# if_arge thus wont change the PLL configuration
|
|
# upon a link status change.
|
|
hint.arge.0.phymask=0x0
|
|
hint.arge.0.miimode=3 # RGMII
|
|
hint.arge.0.media=1000
|
|
hint.arge.0.fduplex=1
|
|
hint.arge.0.pll_1000=0x56000000
|
|
|
|
hint.arge.0.eeprommac=0x1f01fc00
|
|
|
|
# arge1 - lock up to 1000/full
|
|
hint.arge.1.phymask=0x0
|
|
hint.arge.1.media=1000
|
|
hint.arge.1.fduplex=1
|
|
hint.arge.1.miimode=5 # SGMII
|
|
hint.arge.1.pll_1000=0x03000101
|
|
|
|
# hint.arge.1.eeprommac=0x1f01fc06
|
|
|
|
# ath0: Where the ART is - last 64k in the flash
|
|
hint.ath.0.eepromaddr=0x1fff0000
|
|
hint.ath.0.eepromsize=16384
|
|
|
|
# 128 KiB u-boot
|
|
hint.map.0.at="flash/spi0"
|
|
hint.map.0.start=0x00000000
|
|
hint.map.0.end=0x00020000 # 128k u-boot
|
|
hint.map.0.name="u-boot"
|
|
hint.map.0.readonly=1
|
|
|
|
# The TP-Link firmware will put the kernel first (variable size);
|
|
# then the rootfs will be placed hopefully at a 64KiB alignment
|
|
# by whatever calls mktplinkfw.
|
|
|
|
hint.map.1.at="flash/spi0"
|
|
hint.map.1.start=0x00020000
|
|
hint.map.1.end="search:0x00020000:0x10000:.!/bin/sh"
|
|
hint.map.1.name="kernel"
|
|
hint.map.1.readonly=1
|
|
|
|
hint.map.2.at="flash/spi0"
|
|
hint.map.2.start="search:0x00020000:0x10000:.!/bin/sh"
|
|
hint.map.2.end=0x007d0000
|
|
hint.map.2.name="rootfs"
|
|
hint.map.2.readonly=1
|
|
|
|
# 64KiB cfg
|
|
hint.map.3.at="flash/spi0"
|
|
hint.map.3.start=0x007d0000
|
|
hint.map.3.end=0x007e0000
|
|
hint.map.3.name="cfg"
|
|
hint.map.3.readonly=0
|
|
|
|
# 64KiB mib0
|
|
hint.map.4.at="flash/spi0"
|
|
hint.map.4.start=0x007e0000
|
|
hint.map.4.end=0x007f0000
|
|
hint.map.4.name="mib0"
|
|
hint.map.4.readonly=1
|
|
|
|
# 64KiB ART
|
|
hint.map.5.at="flash/spi0"
|
|
hint.map.5.start=0x007f0000
|
|
hint.map.5.end=0x00800000 # 64k ART
|
|
hint.map.5.name="ART"
|
|
hint.map.5.readonly=1
|