c37904e8ba
and start teaching subsystems about it. The Atheros MIPS platforms don't guarantee any kind of FIFO consistency with interrupts in hardware. So software needs to do a flush when it receives an interrupt and before it calls the interrupt handler. There are new ones for the QCA934x and QCA955x, so do a few things: * Get rid of the individual ones (for ethernet and IP2); * Create a mux and enum listing all the variations on DDR flushes; * replace the uses of IP2 with the relevant one (which will typically be "PCI" here); * call the USB DDR flush before calling the real USB interrupt handlers; * call the ethernet one upon receiving an interrupt that's for us, rather than never calling it during operation. Tested: * QCA9558 (TP-Link archer c7 v2) * AR9331 (Carambola 2) TODO: * PCI, USB, ethernet, etc need to do a double-check to see if the interrupt was truely for them before doing the DDR. For now I prefer "correct" over "fast".
471 lines
12 KiB
C
471 lines
12 KiB
C
/*-
|
|
* Copyright (c) 2013 Adrian Chadd <adrian@FreeBSD.org>
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
#include "opt_ddb.h"
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/conf.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/cons.h>
|
|
#include <sys/kdb.h>
|
|
#include <sys/reboot.h>
|
|
|
|
#include <vm/vm.h>
|
|
#include <vm/vm_page.h>
|
|
|
|
#include <net/ethernet.h>
|
|
|
|
#include <machine/clock.h>
|
|
#include <machine/cpu.h>
|
|
#include <machine/cpuregs.h>
|
|
#include <machine/hwfunc.h>
|
|
#include <machine/md_var.h>
|
|
#include <machine/trap.h>
|
|
#include <machine/vmparam.h>
|
|
|
|
#include <mips/atheros/ar71xxreg.h>
|
|
#include <mips/atheros/ar934xreg.h>
|
|
|
|
#include <mips/atheros/ar71xx_cpudef.h>
|
|
#include <mips/atheros/ar71xx_setup.h>
|
|
|
|
#include <mips/atheros/ar71xx_chip.h>
|
|
#include <mips/atheros/ar934x_chip.h>
|
|
|
|
static void
|
|
ar934x_chip_detect_mem_size(void)
|
|
{
|
|
}
|
|
|
|
static uint32_t
|
|
ar934x_get_pll_freq(uint32_t ref, uint32_t ref_div, uint32_t nint,
|
|
uint32_t nfrac, uint32_t frac, uint32_t out_div)
|
|
{
|
|
uint64_t t;
|
|
uint32_t ret;
|
|
|
|
t = u_ar71xx_refclk;
|
|
t *= nint;
|
|
t = t / ref_div;
|
|
ret = t;
|
|
|
|
t = u_ar71xx_refclk;
|
|
t *= nfrac;
|
|
t = t / (ref_div * frac);
|
|
ret += t;
|
|
|
|
ret /= (1 << out_div);
|
|
return (ret);
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_detect_sys_frequency(void)
|
|
{
|
|
uint32_t pll, out_div, ref_div, nint, nfrac, frac, clk_ctrl, postdiv;
|
|
uint32_t cpu_pll, ddr_pll;
|
|
uint32_t bootstrap;
|
|
uint32_t reg;
|
|
|
|
bootstrap = ATH_READ_REG(AR934X_RESET_REG_BOOTSTRAP);
|
|
if (bootstrap & AR934X_BOOTSTRAP_REF_CLK_40)
|
|
u_ar71xx_refclk = 40 * 1000 * 1000;
|
|
else
|
|
u_ar71xx_refclk = 25 * 1000 * 1000;
|
|
|
|
pll = ATH_READ_REG(AR934X_SRIF_CPU_DPLL2_REG);
|
|
if (pll & AR934X_SRIF_DPLL2_LOCAL_PLL) {
|
|
out_div = (pll >> AR934X_SRIF_DPLL2_OUTDIV_SHIFT) &
|
|
AR934X_SRIF_DPLL2_OUTDIV_MASK;
|
|
pll = ATH_READ_REG(AR934X_SRIF_CPU_DPLL1_REG);
|
|
nint = (pll >> AR934X_SRIF_DPLL1_NINT_SHIFT) &
|
|
AR934X_SRIF_DPLL1_NINT_MASK;
|
|
nfrac = pll & AR934X_SRIF_DPLL1_NFRAC_MASK;
|
|
ref_div = (pll >> AR934X_SRIF_DPLL1_REFDIV_SHIFT) &
|
|
AR934X_SRIF_DPLL1_REFDIV_MASK;
|
|
frac = 1 << 18;
|
|
} else {
|
|
pll = ATH_READ_REG(AR934X_PLL_CPU_CONFIG_REG);
|
|
out_div = (pll >> AR934X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
|
|
AR934X_PLL_CPU_CONFIG_OUTDIV_MASK;
|
|
ref_div = (pll >> AR934X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
|
|
AR934X_PLL_CPU_CONFIG_REFDIV_MASK;
|
|
nint = (pll >> AR934X_PLL_CPU_CONFIG_NINT_SHIFT) &
|
|
AR934X_PLL_CPU_CONFIG_NINT_MASK;
|
|
nfrac = (pll >> AR934X_PLL_CPU_CONFIG_NFRAC_SHIFT) &
|
|
AR934X_PLL_CPU_CONFIG_NFRAC_MASK;
|
|
frac = 1 << 6;
|
|
}
|
|
|
|
cpu_pll = ar934x_get_pll_freq(u_ar71xx_refclk, ref_div, nint,
|
|
nfrac, frac, out_div);
|
|
|
|
pll = ATH_READ_REG(AR934X_SRIF_DDR_DPLL2_REG);
|
|
if (pll & AR934X_SRIF_DPLL2_LOCAL_PLL) {
|
|
out_div = (pll >> AR934X_SRIF_DPLL2_OUTDIV_SHIFT) &
|
|
AR934X_SRIF_DPLL2_OUTDIV_MASK;
|
|
pll = ATH_READ_REG(AR934X_SRIF_DDR_DPLL1_REG);
|
|
nint = (pll >> AR934X_SRIF_DPLL1_NINT_SHIFT) &
|
|
AR934X_SRIF_DPLL1_NINT_MASK;
|
|
nfrac = pll & AR934X_SRIF_DPLL1_NFRAC_MASK;
|
|
ref_div = (pll >> AR934X_SRIF_DPLL1_REFDIV_SHIFT) &
|
|
AR934X_SRIF_DPLL1_REFDIV_MASK;
|
|
frac = 1 << 18;
|
|
} else {
|
|
pll = ATH_READ_REG(AR934X_PLL_DDR_CONFIG_REG);
|
|
out_div = (pll >> AR934X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
|
|
AR934X_PLL_DDR_CONFIG_OUTDIV_MASK;
|
|
ref_div = (pll >> AR934X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
|
|
AR934X_PLL_DDR_CONFIG_REFDIV_MASK;
|
|
nint = (pll >> AR934X_PLL_DDR_CONFIG_NINT_SHIFT) &
|
|
AR934X_PLL_DDR_CONFIG_NINT_MASK;
|
|
nfrac = (pll >> AR934X_PLL_DDR_CONFIG_NFRAC_SHIFT) &
|
|
AR934X_PLL_DDR_CONFIG_NFRAC_MASK;
|
|
frac = 1 << 10;
|
|
}
|
|
|
|
ddr_pll = ar934x_get_pll_freq(u_ar71xx_refclk, ref_div, nint,
|
|
nfrac, frac, out_div);
|
|
|
|
clk_ctrl = ATH_READ_REG(AR934X_PLL_CPU_DDR_CLK_CTRL_REG);
|
|
|
|
postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_SHIFT) &
|
|
AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_MASK;
|
|
|
|
if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_PLL_BYPASS)
|
|
u_ar71xx_cpu_freq = u_ar71xx_refclk;
|
|
else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPUCLK_FROM_CPUPLL)
|
|
u_ar71xx_cpu_freq = cpu_pll / (postdiv + 1);
|
|
else
|
|
u_ar71xx_cpu_freq = ddr_pll / (postdiv + 1);
|
|
|
|
postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_SHIFT) &
|
|
AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_MASK;
|
|
|
|
if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_PLL_BYPASS)
|
|
u_ar71xx_ddr_freq = u_ar71xx_refclk;
|
|
else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDRCLK_FROM_DDRPLL)
|
|
u_ar71xx_ddr_freq = ddr_pll / (postdiv + 1);
|
|
else
|
|
u_ar71xx_ddr_freq = cpu_pll / (postdiv + 1);
|
|
|
|
postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_SHIFT) &
|
|
AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_MASK;
|
|
|
|
if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_PLL_BYPASS)
|
|
u_ar71xx_ahb_freq = u_ar71xx_refclk;
|
|
else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL)
|
|
u_ar71xx_ahb_freq = ddr_pll / (postdiv + 1);
|
|
else
|
|
u_ar71xx_ahb_freq = cpu_pll / (postdiv + 1);
|
|
|
|
u_ar71xx_wdt_freq = u_ar71xx_refclk;
|
|
u_ar71xx_uart_freq = u_ar71xx_refclk;
|
|
|
|
/*
|
|
* Next, fetch reference clock speed for MDIO bus.
|
|
*/
|
|
reg = ATH_READ_REG(AR934X_PLL_SWITCH_CLOCK_CONTROL_REG);
|
|
if (reg & AR934X_PLL_SWITCH_CLOCK_CONTROL_MDIO_CLK_SEL) {
|
|
printf("%s: mdio=100MHz\n", __func__);
|
|
u_ar71xx_mdio_freq = (100 * 1000 * 1000);
|
|
} else {
|
|
printf("%s: mdio=%d Hz\n", __func__, u_ar71xx_refclk);
|
|
u_ar71xx_mdio_freq = u_ar71xx_refclk;
|
|
}
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_device_stop(uint32_t mask)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR934X_RESET_REG_RESET_MODULE);
|
|
ATH_WRITE_REG(AR934X_RESET_REG_RESET_MODULE, reg | mask);
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_device_start(uint32_t mask)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR934X_RESET_REG_RESET_MODULE);
|
|
ATH_WRITE_REG(AR934X_RESET_REG_RESET_MODULE, reg & ~mask);
|
|
}
|
|
|
|
static int
|
|
ar934x_chip_device_stopped(uint32_t mask)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR934X_RESET_REG_RESET_MODULE);
|
|
return ((reg & mask) == mask);
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_set_mii_speed(uint32_t unit, uint32_t speed)
|
|
{
|
|
|
|
/* XXX TODO */
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* XXX TODO !!
|
|
*/
|
|
static void
|
|
ar934x_chip_set_pll_ge(int unit, int speed, uint32_t pll)
|
|
{
|
|
|
|
switch (unit) {
|
|
case 0:
|
|
ATH_WRITE_REG(AR934X_PLL_ETH_XMII_CONTROL_REG, pll);
|
|
break;
|
|
case 1:
|
|
/* XXX nothing */
|
|
break;
|
|
default:
|
|
printf("%s: invalid PLL set for arge unit: %d\n",
|
|
__func__, unit);
|
|
return;
|
|
}
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_ddr_flush(ar71xx_flush_ddr_id_t id)
|
|
{
|
|
|
|
switch (id) {
|
|
case AR71XX_CPU_DDR_FLUSH_GE0:
|
|
ar71xx_ddr_flush(AR934X_DDR_REG_FLUSH_GE0);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_GE1:
|
|
ar71xx_ddr_flush(AR934X_DDR_REG_FLUSH_GE1);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_USB:
|
|
ar71xx_ddr_flush(AR934X_DDR_REG_FLUSH_USB);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_PCIE:
|
|
ar71xx_ddr_flush(AR934X_DDR_REG_FLUSH_PCIE);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_WMAC:
|
|
ar71xx_ddr_flush(AR934X_DDR_REG_FLUSH_WMAC);
|
|
break;
|
|
default:
|
|
printf("%s: invalid DDR flush id (%d)\n", __func__, id);
|
|
break;
|
|
}
|
|
}
|
|
|
|
|
|
static uint32_t
|
|
ar934x_chip_get_eth_pll(unsigned int mac, int speed)
|
|
{
|
|
uint32_t pll;
|
|
|
|
switch (speed) {
|
|
case 10:
|
|
pll = AR934X_PLL_VAL_10;
|
|
break;
|
|
case 100:
|
|
pll = AR934X_PLL_VAL_100;
|
|
break;
|
|
case 1000:
|
|
pll = AR934X_PLL_VAL_1000;
|
|
break;
|
|
default:
|
|
printf("%s%d: invalid speed %d\n", __func__, mac, speed);
|
|
pll = 0;
|
|
}
|
|
return (pll);
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_reset_ethernet_switch(void)
|
|
{
|
|
|
|
ar71xx_device_stop(AR934X_RESET_ETH_SWITCH);
|
|
DELAY(100);
|
|
ar71xx_device_start(AR934X_RESET_ETH_SWITCH);
|
|
DELAY(100);
|
|
}
|
|
|
|
static void
|
|
ar934x_configure_gmac(uint32_t gmac_cfg)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR934X_GMAC_REG_ETH_CFG);
|
|
printf("%s: ETH_CFG=0x%08x\n", __func__, reg);
|
|
|
|
reg &= ~(AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0 |
|
|
AR934X_ETH_CFG_MII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE |
|
|
AR934X_ETH_CFG_SW_PHY_SWAP);
|
|
|
|
reg |= gmac_cfg;
|
|
|
|
ATH_WRITE_REG(AR934X_GMAC_REG_ETH_CFG, reg);
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_init_usb_peripheral(void)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR934X_RESET_REG_BOOTSTRAP);
|
|
if (reg & AR934X_BOOTSTRAP_USB_MODE_DEVICE)
|
|
return;
|
|
|
|
ar71xx_device_stop(AR934X_RESET_USBSUS_OVERRIDE);
|
|
DELAY(100);
|
|
|
|
ar71xx_device_start(AR934X_RESET_USB_PHY);
|
|
DELAY(100);
|
|
|
|
ar71xx_device_start(AR934X_RESET_USB_PHY_ANALOG);
|
|
DELAY(100);
|
|
|
|
ar71xx_device_start(AR934X_RESET_USB_HOST);
|
|
DELAY(100);
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_set_mii_if(uint32_t unit, uint32_t mii_mode)
|
|
{
|
|
|
|
/*
|
|
* XXX !
|
|
*
|
|
* Nothing to see here; although gmac0 can have its
|
|
* MII configuration changed, the register values
|
|
* are slightly different.
|
|
*/
|
|
}
|
|
|
|
/*
|
|
* XXX TODO: fetch default MII divider configuration
|
|
*/
|
|
|
|
static void
|
|
ar934x_chip_reset_wmac(void)
|
|
{
|
|
|
|
/* XXX TODO */
|
|
}
|
|
|
|
static void
|
|
ar934x_chip_init_gmac(void)
|
|
{
|
|
long gmac_cfg;
|
|
|
|
if (resource_long_value("ar934x_gmac", 0, "gmac_cfg",
|
|
&gmac_cfg) == 0) {
|
|
printf("%s: gmac_cfg=0x%08lx\n",
|
|
__func__,
|
|
(long) gmac_cfg);
|
|
ar934x_configure_gmac((uint32_t) gmac_cfg);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Reset the NAND Flash Controller.
|
|
*
|
|
* + active=1 means "make it active".
|
|
* + active=0 means "make it inactive".
|
|
*/
|
|
static void
|
|
ar934x_chip_reset_nfc(int active)
|
|
{
|
|
|
|
if (active) {
|
|
ar71xx_device_start(AR934X_RESET_NANDF);
|
|
DELAY(100);
|
|
|
|
ar71xx_device_start(AR934X_RESET_ETH_SWITCH_ANALOG);
|
|
DELAY(250);
|
|
} else {
|
|
ar71xx_device_stop(AR934X_RESET_ETH_SWITCH_ANALOG);
|
|
DELAY(250);
|
|
|
|
ar71xx_device_stop(AR934X_RESET_NANDF);
|
|
DELAY(100);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Configure the GPIO output mux setup.
|
|
*
|
|
* The AR934x introduced an output mux which allowed
|
|
* certain functions to be configured on any pin.
|
|
* Specifically, the switch PHY link LEDs and
|
|
* WMAC external RX LNA switches are not limited to
|
|
* a specific GPIO pin.
|
|
*/
|
|
static void
|
|
ar934x_chip_gpio_output_configure(int gpio, uint8_t func)
|
|
{
|
|
uint32_t reg, s;
|
|
uint32_t t;
|
|
|
|
if (gpio > AR934X_GPIO_COUNT)
|
|
return;
|
|
|
|
reg = AR934X_GPIO_REG_OUT_FUNC0 + 4 * (gpio / 4);
|
|
s = 8 * (gpio % 4);
|
|
|
|
/* read-modify-write */
|
|
t = ATH_READ_REG(AR71XX_GPIO_BASE + reg);
|
|
t &= ~(0xff << s);
|
|
t |= func << s;
|
|
ATH_WRITE_REG(AR71XX_GPIO_BASE + reg, t);
|
|
|
|
/* flush write */
|
|
ATH_READ_REG(AR71XX_GPIO_BASE + reg);
|
|
}
|
|
|
|
struct ar71xx_cpu_def ar934x_chip_def = {
|
|
&ar934x_chip_detect_mem_size,
|
|
&ar934x_chip_detect_sys_frequency,
|
|
&ar934x_chip_device_stop,
|
|
&ar934x_chip_device_start,
|
|
&ar934x_chip_device_stopped,
|
|
&ar934x_chip_set_pll_ge,
|
|
&ar934x_chip_set_mii_speed,
|
|
&ar934x_chip_set_mii_if,
|
|
&ar934x_chip_get_eth_pll,
|
|
&ar934x_chip_ddr_flush,
|
|
&ar934x_chip_init_usb_peripheral,
|
|
&ar934x_chip_reset_ethernet_switch,
|
|
&ar934x_chip_reset_wmac,
|
|
&ar934x_chip_init_gmac,
|
|
&ar934x_chip_reset_nfc,
|
|
&ar934x_chip_gpio_output_configure,
|
|
};
|