Calling rte_eth_dev_get_dcb_info to get dcb info from i40e
driver if VMDQ is disabled, results in a segmentation fault.
This patch fixes it by treating VMDQ and No-VMDQ respectively
when querying dcb information.
Fixes: 5135f3ca49a7 ("i40e: enable DCB in VMDQ VSIs")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Build log:
/root/dpdk/app/test-pmd/cmdline.c:6687:45: error: no member named
's6_addr32' in 'struct in6_addr'
rte_be_to_cpu_32(res->ip_value.addr.ipv6.s6_addr32[i]);
This is caused by macro "s6_addr32" not defined on FreeBSD and testpmd
swap big endian parameter to host endian. Move the swap action to i40e
ethdev will fix this issue.
Fixes: 7b1312891b69 ("ethdev: add IP in GRE tunnel")
Signed-off-by: Marvin Liu <yong.liu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Bruce Richardson <bruce.richardson@intel.com>
The code uses "entry" in the next loop of LIST_FOREACH after calling free()
on it in i40e_res_pool_destroy().
Change to a safe way to free entry, which is similar with LIST_FOREACH_SAFE
in FreeBSD.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Jiangu Zhao <zhaojg@arraynetworks.com.cn>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
This patch extends flow director to select vlan id as part of
filter's input set and program the filter rule with vlan id.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds missing VLAN bitmask for inner frame in case of
tunneling and fixes VLAN tags bitmasks for single or outer frame
in case of tunneling.
Fixes: 98f055707685 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch extends flow director to select more IP Header fields
as filter input set.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
This patch adds a new function to set the fdir input set to default
when initialization.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
In this patch, flex payload is removed from valid fdir input set
values. This is because all flex payload configuration can be set
in struct rte_fdir_conf during device configure phase, which is
a more flexible way of setting this up.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
For the input set selection, Hash filter and Flow director shared
the same function, i.e. i40e_filter_inset_select.
For code readability, this patch replaces i40e_filter_inset_select
with two new functions: i40e_hash_filter_inset_select and
i40e_fdir_filter_inset_select for Hash filter and Flow director
respectively.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Add a new API rte_eth_dev_get_supported_ptypes to query what packet types
can be filled by a given device. The device should be already started or
its PMD RX burst function already decided, since the packet types supported
may vary depending on RX function.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Comment for "ierrors" counter says that it counts erroneous received
packets. But for some reason "imissed" counter is added to "ierrors"
counter in most drivers.
It is a mistake, because missed packets are obviously not received.
This patch fixes it.
Fixes: 70bdb18657da ("ethdev: add Rx error counters for missed, badcrc and badlen packets")
Fixes: 6bfe648406b5 ("i40e: add Rx error statistics")
Fixes: 856505d303f4 ("cxgbe: add port statistics")
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
This patch implemented the ops of adding and removing mac
address in i40evf driver. Functions are assigned like:
.mac_addr_add = i40evf_add_mac_addr,
.mac_addr_remove = i40evf_del_mac_addr,
To support multiple mac addresses setting, this patch also
extended the mac addresses adding and deletion when device
start and stop. Each VF can have a maximum of 64 mac
addresses.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Zhe Tao <zhe.tao@intel.com>
VEB switching feature for i40e is used to enable the switching between the
VSIs connect to the virtual bridge. The old implementation is setting the
virtual bridge mode as VEPA which is port aggregation. Enable the switching
ability by setting the loop back mode for the specific VSIs which connect
to PF or VFs.
VEB/VSI/VEPA are concepts not specific to the i40e HW, the concepts are
from 802.1qbg spec
IEEE EVB tutorial:
http://www.ieee802.org/802_tutorials/2009-11/evb-tutorial-draft-20091116_v09.pdf
VEB: a virtual switch can forward the packet based on the specific match
field.
VSI: a virtual interface connect between the VEB/VEPA and virtual machine.
VEPA: a virtual Ethernet port aggregator will upstream the packets from
VSI to the LAN port.
Signed-off-by: Zhe Tao <zhe.tao@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Previously, DCB(Data Center Bridging) is only enabled on PF,
queue mapping and BW configuration is only done on PF.
This patch enables DCB for VMDQ VSIs(Virtual Station Interfaces)
by following steps:
1. Take BW and ETS(Enhanced Transmission Selection)
configuration on VEB(Virtual Ethernet Bridge).
2. Take BW and ETS configuration on VMDQ VSIs.
3. Update TC(Traffic Class) and queues mapping on VMDQ VSIs.
To enable DCB on VMDQ, the number of TCs should not be larger than
the number of queues in VMDQ pools, and the number of queues per
VMDQ pool is specified by CONFIG_RTE_LIBRTE_I40E_QUEUE_NUM_PER_VM
in config/common_* file.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Several structures and macros are added or updated, such
as 'struct i40e_aqc_get_link_status',
'struct i40e_aqc_run_phy_activity' and
'struct i40e_aqc_lldp_set_local_mib_resp'.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
RX control register read/write functions are added, as directly
read/write may fail when under stress small traffic. After the
adminq is ready, all rx control registers should be read/written
by dedicated functions.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
VLAN filtering was always performed, even if hw_vlan_filter was
disabled. During device initialization, default filter
RTE_MACVLAN_PERFECT_MATCH was applied. In this situation, all incoming
VLAN frames were dropped by the card (increase of the register RUPP - Rx
Unsupported Protocol).
In order to restore default behavior, if HW VLAN filtering is activated,
set a filter to match MAC and VLAN. If not, set a filter to only match
MAC.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Fixes: 912b595146d6 ("i40e: mac vlan filter")
Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Change the fields of outer_mac and inner_mac in struct
rte_eth_tunnel_filter_conf from pointer to struct in order to
keep the code's readability.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Signed-off-by: Jijiang Liu <jijiang.liu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The names of function for tunnel port configuration are not
accurate. They're tunnel_add/del, better change them to
tunnel_port_add/del.
The old functions are directly replaced because the API and ABI
compatibility of ethdev are already broken in 16.04.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
In order to set ether type of VLAN for single VLAN, inner
and outer VLAN, the VLAN type as an input parameter is added
to 'rte_eth_dev_set_vlan_ether_type()'.
In addition, corresponding changes in e1000, ixgbe and i40e
are also added.
It is an ABI break but ethdev library is already bumped for 16.04.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
PCIe feature of 'Extended Tag' is important for 40G performance.
It adds its enabling during each port initialization, to ensure
the high performance.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
fix the error reported by checkpatch:
"ERROR: return is not a function, parentheses are not required"
remove parentheses in return like:
"return (logical expressions)"
remove parentheses in return a function like:
"return (rte_mempool_lookup(...))"
Fixes: 6307b909b8e0 ("lib: remove extra parenthesis after return")
Signed-off-by: Huawei Xie <huawei.xie@intel.com>
In FreeBsd driver, the max frame size is changed to MTU, but not
keep the default value defined in DataSheet. When DPDK runs on that
NIC, the configured value is not expected.
This patch sets the max frame size to default when initialization.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
It corrects the input set values to be set for vlan or
double vlan.
Fixes: 98f055707685 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
There is a compilation issue with some compilers.
In i686 platform, long is 32bit, so XXX_CYCLECOUNTER_MASK
need define as 'ULL'
Fixes: 9c857bf6be87 ("igb: support ieee1588 functions for device time")
Fixes: 1c4445e1f28e ("ixgbe: support ieee1588 functions for device time")
Fixes: f3a4e40eca0c ("i40e: support ieee1588 functions for device time")
Signed-off-by: Michael Qiu <michael.qiu@intel.com>
If DCB is not enabled, the BW info is not stored for VSI. This
patch fixes this issue by merging functions i40e_vsi_dump_bw_config
and i40e_vsi_get_bw_info together.
Fixes: c8b9a3e3fe1b (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
When NVM version is updated to 5.x, DCB can not be configured. This
issue is because of the FW version validation is not correct.
This patch fixed this issue.
Fixes: c8b9a3e3fe1b (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yulong Pei <yulong.pei@intel.com>
As firmware does not support any link control from software driver
side, any phy config should be ignored as a workaround. Otherwise
the link might not be up again after binding back to kernel driver.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
It fixes the issue of not re-configuring hash enable flags (HENA)
if there is no key.
Fixes: d0a349409bd7 ("i40e: support AQ based RSS config")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch removes the crc bytes from byte counter statistics.
Doing so fixes a bug that CRC bytes were included on TX but not
on RX, causing mismatch of bytes received / sent.
Fixes: 9aace75fc82e ("i40e: fix statistics")
Reported-by: Weichun Chen <weichunx.chen@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
This patch refactors the queue and priority statistic handling.
Generic queue stats are presented by rte_eth_xstats_get(), and the
i40e_xstats_get() exposes only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
It fixes the issue of trying to allocate more VSIs for VMDq than
hardware remaining. It adds a check of the hardware remaining
before allocating VSIs for VMDq.
Fixes: c80707a0fd9c ("i40e: fix VMDq pool limit")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
This patch fixes a bug where only some of the statistics were being
reset when calling rte_eth_stats_reset() or rte_eth_xstats_reset().
As both the stats reset and xstats reset do the same, refactor away
the duplicated function.
This patch marks the VSI to update its offset, causing the stats be
look like they are reset.
Fixes: 9aace75fc82e ("i40e: fix statistics")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This fixes the issue of not freeing memzone in a call to free the
memory for adminq DMA.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
It fixes the issue of cannot using more than 1 poor for VMDq,
according to the queues left.
Fixes: 705b57f82054 ("i40e: enlarge the number of supported queues")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
It fixes compile issue on ICC 13.0.0.
Error logs:
i40e_ethdev.c(7943): error #188: enumerated type mixed with another type
Fixes: c8b9a3e3fe1b ("i40e: support DCB mode")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
The patch enables rx interrupt support on i40e VF and some necessary
change on PF IOV mode to support VF.
On PF side, running in IOV mode via uio won't allow rx interrupt
which is exclusive with mbox interrupt in single vector competition.
On VF side, one single vector is shared for all the rx queues.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
The patch enables rx interrupt support on i40e PF non-IOV mode.
Per queue rx interrupt works on vfio, however on uio, all rx queues
share one interrupt vector.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
The old statistics on i40e only counted the packets on ports.
So the discarding packets on VSI were not counted.
This patch is to make statistics for packets both on ports and VSI.
Also update release notes.
Signed-off-by: Xutao Sun <xutao.sun@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
By default, only first 3 bytes of GRE key will be used for hash or
FD calculation. With these changes, it can select 3 or 4 bytes of
GRE key for hash or FD calculation.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
