If DCB is not enabled, the BW info is not stored for VSI. This
patch fixes this issue by merging functions i40e_vsi_dump_bw_config
and i40e_vsi_get_bw_info together.
Fixes: c8b9a3e3fe1b (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
When NVM version is updated to 5.x, DCB can not be configured. This
issue is because of the FW version validation is not correct.
This patch fixed this issue.
Fixes: c8b9a3e3fe1b (i40e: support DCB mode)
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Yulong Pei <yulong.pei@intel.com>
As firmware does not support any link control from software driver
side, any phy config should be ignored as a workaround. Otherwise
the link might not be up again after binding back to kernel driver.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
It fixes the issue of not re-configuring hash enable flags (HENA)
if there is no key.
Fixes: d0a349409bd7 ("i40e: support AQ based RSS config")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch removes the crc bytes from byte counter statistics.
Doing so fixes a bug that CRC bytes were included on TX but not
on RX, causing mismatch of bytes received / sent.
Fixes: 9aace75fc82e ("i40e: fix statistics")
Reported-by: Weichun Chen <weichunx.chen@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch removes the crc bytes from byte counter statistics.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch removes the crc bytes from byte counter statistics.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This fixes a bug added to em and igb drivers which causes the pci info
seen by the primary process to become invalidated by secondary process
startup.
This call was added after the process type check in the other drivers.
Fixes: eeefe73f0af1 ("drivers: copy PCI device info to ethdev data")
Signed-off-by: Jon DeVree <nuxi@vault24.org>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
When freeing the device it is also neccesary to free
rx_queues and tx_queues
Signed-off-by: Mauricio Vasquez B <mauricio.vasquezbernal@studenti.polito.it>
Add virtual PMD which communicates with COMBO cards through sze2
layer using libsze2 library.
Since link_speed is uint16_t, there can not be used number for 100G
speed, therefore link_speed is set to ETH_LINK_SPEED_10G until the
type of link_speed is solved.
Signed-off-by: Matej Vido <matejvido@gmail.com>
This commit introduce rte_smp_mb(), rte_smp_wmb() and rte_smp_rmb(), in
order to enable memory barriers between lcores.
The patch does not provide any functional change for IA, the goal is to
have infrastructure for weakly ordered machines like ARM to work on DPDK.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
Add additional functions to support the existing IEEE1588
functionality and to enable getting, setting and adjusting
the device time.
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Reviewed-by: John McNamara <john.mcnamara@intel.com>
Use common code to handle Xen support at runtime.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jijiang Liu <jijiang.liu@intel.com>
These statistics are marked deprecated, leave them alone.
Also keep track of imissed across all ports.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This patch refactors the queue and priority statistic handling.
Generic queue stats are presented by rte_eth_xstats_get(), and the
i40e_xstats_get() exposes only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This patch refactors the queue handling. Generic queue stats are
handled by rte_eth_xstats_get() and the ixgbe_xstats_get() exposes
only the extra stats.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
It fixes the issue of trying to allocate more VSIs for VMDq than
hardware remaining. It adds a check of the hardware remaining
before allocating VSIs for VMDq.
Fixes: c80707a0fd9c ("i40e: fix VMDq pool limit")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
ICC complains about enumerated types being mixed in link bonding driver,
as ETH_MQ_RX_RSS is an enum type of mq_mode and not a bitmask as it was
being treated.
Fixes: 734ce47f71e0 ("bonding: support RSS dynamic configuration")
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
One of the ways to reproduce the issue:
testpmd <EAL-OPTIONS> -- -i --txqflags=0
testpmd> set fwd txonly
testpmd> set txpkts 64,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4,4
testpmd> set txsplit rand
testpmd> start
After some time TX on ixgbe queue will hang,
and all packet transmission on that queue will stop.
This bug was first reported and investigated by
Vlad Zolotarov <vladz@cloudius-systems.com>:
"We can reproduce this issue when stressed the xmit path with a lot of highly
fragmented TCP frames (packets with up to 33 fragments with non-headers
fragments as small as 4 bytes) with all offload features enabled."
The root cause is that ixgbe_xmit_pkts() in some cases violates the HW rule
that the distance between TDs with RS bit set should not exceed 40 TDs.
>From the latest 82599 spec update:
"When WTHRESH is set to zero, the software device driver should set the RS bit
in the Tx descriptors with the EOP bit set and at least once in the 40
descriptors."
The fix is to make sure that the distance between TDs with RS bit set
would never exceed HW limit.
As part of that fix, tx_rs_thresh for ixgbe PMD is not allowed to be greater
then to 32 to comply with HW restrictions.
With that fix slight slowdown for the full-featured ixgbe TX path
might be observed (from our testing - up to 4%).
ixgbe simple TX path is unaffected by that patch.
Reported-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch fixes a bug where only some of the statistics were being
reset when calling rte_eth_stats_reset() or rte_eth_xstats_reset().
As both the stats reset and xstats reset do the same, refactor away
the duplicated function.
This patch marks the VSI to update its offset, causing the stats be
look like they are reset.
Fixes: 9aace75fc82e ("i40e: fix statistics")
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Maryam Tahhan <maryam.tahhan@intel.com>
This fixes the issue of not freeing memzone in a call to free the
memory for adminq DMA.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
It fixes the issue of cannot using more than 1 poor for VMDq,
according to the queues left.
Fixes: 705b57f82054 ("i40e: enlarge the number of supported queues")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Fix for the following error on icc 2015, due to incorrect type:
drivers/net/i40e/i40e_fdir.c(1376): error #188:
enumerated type mixed with another type
case RTE_ETH_FDIR_FILTER_INPUT_SET_SELECT:
Fixes: 98f05570 ("i40e: configure input fields for RSS or flow director")
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
It fixes compile issue on ICC 13.0.0.
Error logs:
i40e_ethdev.c(7943): error #188: enumerated type mixed with another type
Fixes: c8b9a3e3fe1b ("i40e: support DCB mode")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Once posted through mailbox, we must check for nack from the PF
and report an error in this case.
Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Report an error when something went wrong.
Signed-off-by: Julien Meunier <julien.meunier@6wind.com>
Signed-off-by: David Marchand <david.marchand@6wind.com>
Acked-by: Sujith Sankar <ssujith@cisco.com>
In case of creating bond device without add any slaves and
quit from testpmd, application crashed since rx/tx queues
are NULL.
Add checking of this parameters before trying to free.
Signed-off-by: Raslsn Darawsheh <rdarawsheh@asaltech.com>
Signed-off-by: Yaacov Hazan <yaacovh@mellanox.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Add support for RTE_ETH_FDIR_PASSTHRU flow director behavior so
output queue is assigned by other filters.
Signed-off-by: Andrey Chilikin <andrey.chilikin@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
This patch removes l3_l4_xsum_errors from rx errors.
The reason to remove it is that UDP packets have an optional checksum, and
when not calculated the checksum field should be set to zero. When the
checksum is not calculated (zero-ed out), the hardware still counts a valid
UDP packet as an l3_l4_xsum_error.
This hardware issue is documented in 82599 errata, titled:
"Integrity Error Reported for IPv4/UDP Packets with Zero Checksum"
The solution is to remove l3_l4_xsum_errors from rx_errors, as discussed on
http://thread.gmane.org/gmane.comp.networking.dpdk.devel/25590/
Fixes: f6bf669b9900 ("ixgbe: account more Rx errors")
Suggested-by: Martin Weiser <martin.weiser@allegro-packets.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Following the same approach taken with dev_started field
in rte_eth_dev_data structure, this patch adds two new fields
in it, rx_queue_state and tx_queue_state arrays, which track
which queues have been started and which not.
This is important to avoid trying to start/stop twice a queue,
which will result in undefined behaviour
(which may cause RX/TX disruption).
Mind that only the PMDs which have queue_start/stop functions
have been changed to update this field, as the functions will
check the queue state before switching it.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The patch enables rx interrupt support on i40e VF and some necessary
change on PF IOV mode to support VF.
On PF side, running in IOV mode via uio won't allow rx interrupt
which is exclusive with mbox interrupt in single vector competition.
On VF side, one single vector is shared for all the rx queues.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
The patch enables rx interrupt support on i40e PF non-IOV mode.
Per queue rx interrupt works on vfio, however on uio, all rx queues
share one interrupt vector.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
As ixgbe vf doesn't support lsc, the patch removes those unused code.
In addition, it does some tiny cleanup.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
When ixgbe runs as a PF, mbox interrupt is prerequisite to make VF
start normally.
And PF sometimes won't 'dev_start', so the mbox interrupt register
during 'dev_init' is required.
The patch rolls back the interrupt register for mbox,lsc to the 'dev_init'.
As UIO doesn't support multiple vector, mbox has to occupy the only one.
It adds condition check on 'dev_start', rxq interrupt is not allowed
when PF running in IOV mode via UIO.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
When igb runs as a PF, mbox interrupt is prerequisite to make VF
start normally.
And PF sometimes won't 'dev_start', so the mbox interrupt register
during 'dev_init' is required.
The patch rolls back the interrupt register for mbox,lsc to the 'dev_init'.
As UIO doesn't support multiple vector, mbox has to occupy the only one.
It adds condition check on 'dev_start', rxq interrupt is not allowed
when PF running in IOV mode via UIO.
Signed-off-by: Cunming Liang <cunming.liang@intel.com>
