FW sets HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ERR_RECOVER_RELOAD
in HWRM_FUNC_QCAPS command, if device requires to invoke
fastboot FW during FW reset.
Driver has to poll for shutdown bit in fw_status register:
1. in case of hot fw upgrade, this bit will be set after all
function drivers unregistered with fw.
2. in case of fw initiated error recovery, this bit will be
set after fw has collected the core dump
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Rahul Gupta <rahul.gupta@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1. Advertise HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_ERROR_RECOVERY_SUPPORT flag
in the FUNC_DRV_RGTR command.
2. request for the async event ASYNC_EVENT_CMPL_EVENT_ID_ERROR_RECOVERY
in the FUNC_DRV_RGTR command.
3. handle the async event EVENT_ID_ERROR_RECOVERY from FW.
Error recovery support will be used by firmware only if all the driver
instances support error recovery process.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
When firmware hit some unrecoverable error conditions, firmware initiate
the recovery by sending an async event EVENT_CMPL_EVENT_ID_RESET_NOTIFY
with data1 set to RESET_NOTIFY_EVENT_DATA1_REASON_CODE_FW_EXCEPTION_FATAL
to all host drivers and will reset the chip.
The recovery procedure is same sequence as the one for hot FW upgrade.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
When the FW upgrade is initiated the current instance
of FW issues a HWRM_ASYNC_EVENT_CMPL_EVENT_ID_RESET_NOTIFY
async notification to the driver. On receiving this notification,
the PMD shall quiesce itself and poll on the HWRM_VER_GET FW
command at regular intervals.
Once the VER_GET command succeeds, the driver should go through
the rediscovery process and re-initialize the device.
Also register with FW for the reset notify async event.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
This commit adds support to the bnxt PMD for devices
based on the BCM57508 "thor" Ethernet controller.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Reduce code duplication and prepare for newer controllers that
use different doorbell protocols by refactoring doorbell handling
code.
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Descriptor fields in CP ring are in little-endian form, convert
to CPU endian before performing arithmetic operations.
Also use more general comparison when checking for ring
index wrap.
Fixes: f2a768d4d1 ("net/bnxt: add completion ring")
Cc: stable@dpdk.org
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Batch more than one Tx requests such that only one completion
is generarted by the HW. We request a Tx completion for first
and last Tx request in the batch.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
In order to save completion resource, use the first completion ring from
PF or VF as the default completion ring for async event & HWRM forward
response handling. Add bnxt_hwrm_set_async_event_cr() to set
async_event_cr for either PF or VF.
Fixes: 7bc8e9a227 ("net/bnxt: support async link notification")
Signed-off-by: Qingmin Liu <qingmin.liu@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Update the license header on bnxt files to be the standard
BSD-3-Clause license used for the rest of DPDK,
bring the files in compliance with the DPDK licensing policy.
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Renamed data type from phys_addr_t to rte_iova_t.
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
1) For a VF, query the firmware to determine if a MAC address is
already configured. If not configure a random default MAC address.
2) Do not initialize the default completion ring in
bnxt_alloc_hwrm_rings().
3) While registering for async events with the firmware,
use func_vf_cfg for a VF and use func_cfg for a PF.
4) Query the VNIC plcmode config using the bnxt_hwrm_vnic_plcmodes_qcfg
before a VNIC is updated. Reconfigure the VNIC with the plcmode
configuration queried earlier. Not doing this could overwrite
the plcmodes in some cases.
5) Reorg the bnxt_handle_fwd_req to properly handle the forwarded
requests. The previous code did not handle it completely.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Replace the raw I/O device memory read/write access with eal abstraction
for I/O device memory read/write access to fix portability issues across
different architectures.
CC: Stephen Hurd <stephen.hurd@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This patch adds support for the Broadcom StrataGX® BCM5871X
series of Communications Processors.
These ARM based processors target a broad range of networking
applications including virtual CPE (vCPE) and NFV appliances,
10G service routers and gateways, control plane processing for
Ethernet switches, and network attached storage (NAS).
Other than adding the PCI Id for supporting the device,
the patch also adds a memory barrier before the Tx doorbell
and Completing ring doorbell is written to. Since ARM has a
weakly ordered memory model this enforces a strict ordering
of the descriptor writes before the doorbell writes happen.
Signed-off-by: John Carney <john.carney@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Perform allocation and free()ing of ring and information structures
for the TX, RX, and completion rings. The previous patches had
so far provided top level stubs and generic ring support, while this
patch does the real allocation and freeing of the memory specific to
each different type of generic ring.
For example bnxt_init_tx_ring_struct() or bnxt_init_rx_ring_struct() is
now allocating memory based on the socked_id being provided.
bnxt_tx_queue_setup_op() or bnxt_rx_queue_setup_op() have gone through
some reformatting to perform a graceful cleanup in case memory
allocation fails.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Initial implementation of tx_pkt_burst for transmit.
bnxt_xmit_pkts() is the top level function that is called during Tx.
bnxt_handle_tx_cp() is used to check and process the Tx completions
generated for the Tx Buffer Descriptors sent by the hardware.
This patch also adds code to allocate rings in the hardware.
For each Tx queue allocated in the PMD driver, a corresponding ring
in hardware will be created. Every time a Tx request is initiated
via the bnxt_xmit_pkts() call, a Buffer Descriptor is created and
is sent to the hardware via the associated Tx ring.
On completing the Tx operation, the hardware will generates the status
in the form of a completion. This completion is processed by the
bnxt_handle_tx_cp() function.
Functions like bnxt_init_tx_ring_struct() and bnxt_init_one_tx_ring()
are used to initialize various members of the structure before
starting Tx operations.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add the bnxt_stats_get_op() and bnxt_stats_reset_op() dev_ops to
get and reset statistics. It also brings in the associated HWRM calls
to handle the requests appropriately.
We also have the bnxt_free_stats() function which will be used in the
follow on patches to free the memory allocated by the driver for
statistics.
New HWRM calls:
bnxt_hwrm_stat_clear:
This command clears statistics of a context
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Structures, macros, and functions for working with completion rings
in the driver.
Completion Ring is used by the Ethernet controller to provide the
status of transmitted & received packets, report errors, report
status changes to the host software, and inter-function forwarding
requests. In addition to the generic ring features, a completion ring
can have a statistics context that has statistics periodically DMAed
to host memory, along with a consumer index.
bnxt_handle_async_event() handles completions not related to a specific
transmit or receive ring such as link status changes which arrive on
the default completion ring.
Other physical or virtual functions on the same device may send an HWRM
command forward request. In this case, we will pass it through
unvalidated. In the future, we will be able to have the PF monitor and
control VF access to the HWRM interface if needed.
New HWRM Calls:
bnxt_hwrm_exec_fwd_resp:
Execute an encapsulated command and forward the response.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
