Add Tx adapter support and move few routines around to avoid code
duplication.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This commit adds a unit test that checks the behaviour
of the unlinks_in_progress() function, ensuring that the
returned values are the number of unlinks requested,
until the scheduler runs and "acks" the requests, after
which the count should be zero again.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
This commit adds a counter to each port, which counts the
number of unlinks that have been performed. When the scheduler
thread starts its scheduling routine, it "acks" all unlinks that
have been requested, and the application is gauranteed that no
more events will be scheduled to the port from the unlinked queue.
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
This commit fixes the cq index checks when unlinking
ports/queues while the scheduler core is running.
Previously, the == comparison could be "skipped" if
in particular corner cases. With the check being changed
to >= this is resolved as the cq idx gets reset to zero.
Bugzilla ID: 60
Fixes: 617995dfc5 ("event/sw: add scheduling logic")
Cc: stable@dpdk.org
Suggested-by: Matias Elo <matias.elo@nokia.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
This patch restructure the code to have the QBMAN portal
affliated at run time for per lcore basis.
The device cleanup is also improved.
Signed-off-by: Sunil Kumar Kori <sunil.kori@nxp.com>
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This patch enhances:
1. Configure the dequeue time out value as per the given
method or per dequeue, global or default.
2. The timeout values were being mixed as ns or ms timeouts,
Now the values are stored as ns and scale is in ms.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Fixes: 7b6edb640b ("event/dpaa2: have separate structure to hold dqrr entries")
Cc: stable@dpdk.org
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The DSW event device now implements the 'xstats' interface and a
number of port- and device-level counters.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
With this patch, the DSW event device will (optionally) sort the event
burst before giving it to the application. The sorting will primarily
be on queue id, and secondary on flow id.
The sorting is an attempt to optimize data and instruction cache usage
for the application, at the cost of additional event device overhead.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
The DSW event device will now attempt to migrate (move) flows between
ports in order to balance the load.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
The DSW event device port now attempts to estimate its load (i.e. how
busy it is). This is required for load balancing to work (although
load balancing is not included in this patch), and may also be useful
for debugging purposes.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
With this patch, the DSW event device can be started and stopped,
and also supports scheduling events between ports.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Added support for linking and unlinking ports to queues in a DSW event
device.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Allow port setup and release in the DSW event device.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Allow queue- and device-level configuration for and retrieval of
contextual information from a DSW event device.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This patch contains the Meson and GNU Make build system extensions
required for the Distributed Event Device, and also the initialization
code for the driver itself.
Signed-off-by: Mattias Rönnblom <mattias.ronnblom@ericsson.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Modifying port state is not necessary when starting/stopping Rx adapter
as it is same as starting/stopping ethdev.
Fixes: 45a914c5bd ("event/octeontx: support event Rx adapter")
Cc: stable@dpdk.org
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
HW needs each pool to be mapped to an aura set of 16 auras.
Previously, pool to aura mapping was considered to be 1:1.
Fixes: 02fd6c7443 ("mempool/octeontx: support allocation")
Cc: stable@dpdk.org
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Santosh Shukla <santosh.shukla@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This commit also adds a flush callback test to the sw eventdev's selftest
suite.
Signed-off-by: Gage Eads <gage.eads@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
When event queues are being flushed the getwork operation used to extract
events should be a grouped getwork operation to the specific event queue.
Fixes: 8384f0e039 ("event/octeontx: support device stop flush callback")
Cc: stable@dpdk.org
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
A constructor is usually declared with RTE_INIT* macros.
As it is a static function, no need to declare before its definition.
The macro is used directly in the function definition.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
This patch defines capabilities & functions to be called
for eventdev PMDs.
Signed-off-by: Abhinandan Gujjar <abhinandan.gujjar@intel.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
Removing use of link data under evq_info_t structure which was
used to check whether the the associated evq has been linked
or not. Since, an evq can be linked to multiple event ports,
thus setting the link variable only allowed the first event
port to be associated with the evq. This led to huge performance
drop in case of multiple event ports as I/O only worked on
first event port associated with the evq.
Fixes: 0ce3ce7c27 ("event/dpaa2: add configuration functions")
Cc: stable@dpdk.org
Signed-off-by: Ashish Jain <ashish.jain@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Driver shouldn't take decision on signals received. The return
from epoll was blocking on EINTR which is not the right use-case.
Fixes: 36d87bb922 ("event/dpaa2: handle timeout using interrupts in dequeue")
Cc: stable@dpdk.org
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Clang 6 & 7 fail to naturally align packed structs due to this clang
can't use 8byte atomic primitives and splits them into lesser atomic
primitives. To use lesser atomic primitives we need to link libatomic
(-latomic), instead supply alignment attribute to the compiler.
timvf_worker.c:(.text+0x498): undefined reference to `__atomic_fetch_add_8'
timvf_worker.c:(.text+0x525): undefined reference to `__atomic_store_2'
timvf_worker.c:(.text+0x557): undefined reference to `__atomic_fetch_add_4'
timvf_worker.c:(.text+0x5de): undefined reference to `__atomic_store_2'
Fixes: f874c1eb15 ("event/octeontx: create and free timer adapter")
Reported-by: Andrew Rybchenko <arybchenko@solarflare.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
The DPCI devices have both Tx and Rx queues. Event devices use
DPCI Rx queues only, but CMDIF (AIOP) uses both Tx and Rx queues.
This patch enables Tx queues configuration too.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
With Hotplugging memory support, the order of memseg has been changed
from physically contiguous to virtual contiguous. FSLMC bus and dpaa2
drivers depend on PA to VA address conversion when in Physical
addressing mode.
This patch creates a list of blocks requested to be pinned to the
DPAA2 mempool. For searching physical addresses, it is expected that
it would belong to this list (from hardware pool) and hence it is
less expensive than memseg walks. Though, this has marginal impact on
performance vis-a-vis legacy mode with physically contiguous memsegs.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Bugzilla-ID: 28
Fixes: f874c1eb15 ("event/octeontx: create and free timer adapter")
Reported-by: Harry van Haaren <harry.van.haaren@intel.com>
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Meson build currently tracks the dependencies between libraries, which
can often make things easier, but has the side-effect of slowing down
the initial meson run if too many duplicated dependencies are provided.
Therefore, we remove dependencies from the dpaa items where other
dependencies already depend on those. This provides a noticable speed-up
in meson configuration runs when lots of sample apps are included in the
build.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
dev_info->max_event_ports is uint8_t. dpaa_event_dev_info_get assigns
DPAA_EVENT_MAX_EVENT_PORT (which is RTE_MAX_LCORE, upto 256 in ppc64le)
into this variable, which breaks compile in ppc64le.
drivers/event/dpaa/dpaa_eventdev.c: In function ‘dpaa_event_dev_info_get’:
rte_config.h:23:23: error:
large integer implicitly truncated to unsigned type [-Werror=overflow]
#define RTE_MAX_LCORE 256
Fixes: 9caac5dd1e ("event/dpaa: introduce PMD")
Cc: stable@dpdk.org
Signed-off-by: Gowrishankar Muthukrishnan <gowrishankar.m@linux.vnet.ibm.com>
Acked-by: Sunil Kumar Kori <sunil.kori@nxp.com>
Add compile-time configurable option to force TIMvf to use Octeontx
FPAvf pool manager as its chunk pool.
When FPAvf is used as pool manager the TIMvf automatically frees the
chunks to FPAvf through gpool-id.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
When application sets `RTE_EVENT_TIMER_ADAPTER_F_ADJUST_RES` flag
while creating adapter underlying driver is free to optimize the
resolution for best possible configuration.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
When application creates the timer adapter by passing
`RTE_EVENT_TIMER_ADAPTER_F_SP_PUT` flag, we can optimize the arm sequence
by removing the locking overhead.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
When application requests to start the timer adapter through
`rte_event_timer_adapter_start`, Octeontx TIMvf ring does the
following:
- Uses mbox to communicate TIMpf driver about,
* SCLK frequency used to convert ns<->cycles.
* program the ring control parameters and start the ring.
* get the exact cycle at which the TIMvf ring has started which can be
used to estimate the bucket position.
On `rte_event_timer_adapter_stop` i.e stop, Octeontx TIMvf ring does the
following:
- Use mbox to communicate TIMpf driver about,
* reset the ring control parameters and stop the ring.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
When the application requests to create a timer device, Octeontx TIM
create does the following:
- Get the requested TIMvf ring based on adapter_id.
- Verify the config parameters supplied.
- Allocate memory required for
* Buckets based on min and max timeout supplied.
* Allocate the chunk pool based on the number of timers.
- Clear the interrupts.
On Free:
- Free the allocated bucket and chunk memory.
- Free private data used by TIMvf.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
On Octeontx HW, each event timer device is enumerated as separate SRIOV VF
PCIe device.
In order to expose as a event timer device:
On PCIe probe, the driver stores the information associated with the
PCIe device and later when application requests for a event timer device
through `rte_event_timer_adapter_create` the driver infrastructure creates
the timer adapter with earlier probed PCIe VF devices.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This commit adds the logic that is shared by all event timer adapter
drivers; the common code handles instance allocation and some
initialization.
Signed-off-by: Erik Gabriel Carrillo <erik.g.carrillo@intel.com>
Acked-by: Pavan Nikhilesh <pbhagavatula@caviumnetworks.com>
Add support for stop flush callback along with unit test.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Gage Eads <gage.eads@intel.com>
When an event device is stopped, it drains all event queues and ports.
These events may contain pointers, so to prevent memory leaks eventdev now
supports a user-provided flush callback that is called during the queue
drain process. This callback is stored in process memory, so the callback
must be registered by any process that may call rte_event_dev_stop().
This commit also clarifies the behavior of rte_event_dev_stop().
This follows this mailing list discussion:
http://dpdk.org/ml/archives/dev/2018-January/087484.html
Signed-off-by: Gage Eads <gage.eads@intel.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
If application link one atomic queue to multiple ports,
and each worker core update flow_id, there will have a
chance to hit race condition issue and lead to double processing
same event. This fix solve the problem and eliminate
the race condition issue.
Fixes: 4236ce9bf5 ("event/opdl: add OPDL ring infrastructure library")
Cc: stable@dpdk.org
Signed-off-by: Liang Ma <liang.j.ma@intel.com>
Signed-off-by: Peter Mccarthy <peter.mccarthy@intel.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
