DEV_RX_OFFLOAD_TIMESTAMP is per port, so the internal implementation
shall enable it on per port basis only.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This experimental API is no longer required as the same
purpose can be solved with standard DEV_RX_OFFLOAD_TIMESTAMP
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Add support for raw flow, which can be used for any
protocol rules.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Default distribution size of TC is 1, which is limited by MC. We have to
set the distribution size for each TC to support multiple RXQs per TC.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Calculate QoS/FS entry index by group and priority of flow.
1)The less index of entry, the higher priority of flow.
2)Verify if the flow with same group and priority has been added before
creating flow.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
1) Support QoS extracts and TC extracts for multiple TCs.
2) Protocol type of L2 extract is used to parse L3.
Next protocol of L3 extract is used to parse L4.
3) generic IP key extracts instead of IPv4 and IPv6 respectively.
4) Special for IP address extracts:
Put IP(v4/v6) address extract(s)/rule(s) at the end of extracts array
to make rest fields at fixed position.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This patch moves the internal symbols to INTERNAL sections
so that any change in them is not reported as ABI breakage.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
This patch adds default/preferred rx/tx params in dev info,
specially the advertised burst size.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
There is a common macro __rte_unused, avoiding warnings,
which is now used where appropriate for consistency.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
This patch sets the priority of the dpcon dev, such that it is
within the supported range of dpcon
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Earlier, there was a single MCP handle which was available across
complete DPAA2 driver as well as part of the dev_private which was
shared by the secondary process.
For secondary, that is not valid and it would require to open its
own handle for the MC. This is eventually used as part of the DPNI
configuration.
By using the process_private member of the rte_eth_dev, it is
possible to keep separate handles per process. Without worry of
overwriting when secondary process accesses the dev_private.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Reviewed-by: Sachin Saxena <sachin.saxena@nxp.com>
This patch adds the support for PTP driver for
DPAA2 devices.
To enable set
CONFIG_RTE_LIBRTE_IEEE1588=y in
config/defconfig_arm64-dpaa2-linuxapp-gc
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
TX confirmation mode provides dedicated confirmation
queues for transmitted packets. These queues are used
by software to get the status and release
transmitted packets buffers.
By default TX confirmation mode is kept disabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
The existing taildrop was based on queue data size.
This patch replaces it with frame count bases using
CGR methods of DPAA2 device.
The number of CGRs are limited. So,
- use per queue CGR based tail drop for as many as CGR
available.
- Remaining queues shall use the legacy byte based tail drop
Number of CGRs can be controlled by dpl file during dpni_create.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
When we need particular number of packets from the rx routine,
which would change in every call, we cannot prefetch the packets
and provide previous results to the user.
User can select the mode by using devargs for non prefetch mode.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
This patch introduces an rte pmd API to configure dpdmux from
the application.
dpdmux can work in association with dpni as an additional
distribution capability on the NIC.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
This patch enables the population of timestamp field
in mbuf on packet receive.
It may give performance impact on LX2xxx platforms.
So, it has been made optional for Lx2xxx platform.
One shall call, rte_dpaa2_enable_ts() to enable it.
Nothing is required for LS2 and LS1088 platforms.
Signed-off-by: Akhil Goyal <akhil.goyal@nxp.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Adding support for DPDK packet parsing logic for LX2
platform to accommodate the new FRC format introduced in LX2.
Signed-off-by: Ashish Jain <ashish.jain@nxp.com>
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
For larger packet size congestion is observed on Tx Queues.
This patch enables Tx Queue congestion state check support.
If congested, try to resend the packet few times.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
NXP Copyright has been wrongly worded with '(c)' at various places.
This patch removes these extra characters. It also removes
"All rights reserved".
Only NXP copyright syntax is changed. Freescale copyright is not
modified.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Typically when the PMD issues a Rx command to DPAA2 hardware,
the HW writes the available descriptors into the given memory.
The RX function then processes the frames and prepare them as
mbufs.
This patch adds support to issue another pull request to hardware
in another memory location, before we start processing the output
of the first request. This help in controlling the CPU cycles
wasted during the wait for the hardware to write the descriptors.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
