This patch deletes some unused capabilities, include:
1. Delete some unused firmware capabilities definition, which are:
UDP_GSO, ATR, INT_QL, SIMPLE_BD, TX_PUSH, FEC and PAUSE.
2. Delete some unused driver capabilities definition, which are:
UDP_GSO, TX_PUSH.
3. Also redefine HNS3_DEV_SUPPORT_* as enum type, and change some of
the values. Note: the HNS3_DEV_SUPPORT_* values is used only inside
the driver, so it's safe to change the values.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The hns3_is_csq() and cmq_ring_to_dev() macro were defined in previous
version but never used.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch supports runtime config of mask device capability, it was
used to mask the capability which queried from firmware.
The device argument key is "dev_caps_mask" which takes hexadecimal
bitmask where each bit represents whether mask corresponding capability.
Its main purpose is to debug and avoid problems.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng 930 uses a new RAS exception reporting solution.
The reset type and exception status are reported through
firmware. The driver modifies the corresponding code to
adapt to the new solution.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The firmware compatibility configuration in PF driver is used to
maintain the compatibility of some features of the driver and
firmware, and requires firmware to enable these features. Currently,
the configuration is in hns3_init_hardware(), which is a little back.
Because firmware may clear some configurations (such as, MAC related)
after receiving the command. And firmware can not be aware of some
default initializations (such as, flow control) before executing the
command to set the copper PHY when the PHY is controlled by firmware.
Therefore, it is recommended that no other hardware resources are
configured before the compatibility configuration. And it should be
moved to hns3_cmd_init(), which is responsible for the firmware
command initialization of driver.
In addition, the driver needs to perform corresponding processing
if the command fails to be sent.
1) If firmware fails to take over the copper PHY, the copper port fails
to initialize.
2) If fails to enable the report of link events, the device does not
support the LSC capability.
Fixes: bff6ebfe30d4 ("net/hns3: refactor PF LSC event report")
Fixes: bac6a06441 ("net/hns3: fix link status change from firmware")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The PTP depends on special packet type reported by hardware which
enabled rxd advanced layout, so if the hardware doesn't support rxd
advanced layout, driver should ignore the PTP capability.
Fixes: 4387523581 ("net/hns3: get device capability from firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The type of return value of hns3_cmd_send is int, some function declare
the return value as hns3_cmd_status.
This patch fix the incorrect use of the enum hns3_cmd_status.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Fixes: 02a7b55657 ("net/hns3: support Rx interrupt")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
When FLR occurs, the head pointer register of
the command queue will be cleared, resulting in
abnormal detection of the head pointer register
of the command queue. At present, FLR is detected
in this way, and the reset recovery process is
executed.
However, when FLR occurs, the header pointer
register of the command queue is not necessarily
abnormal. For example, when the driver runs
normally, the value of the header pointer register
of the command queue may also be 0, which will
lead to the miss detection of FLR.
Therefore, the judgment that whether the base
address register of command queue is 0 is added
to ensure that FLR not miss detection.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch updates copyright date for hns3 PMD files.
Fixes: 565829db8b ("net/hns3: add build and doc infrastructure")
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Fixes: e31f123db0 ("net/hns3: support NEON Tx")
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
According to the suggestion of our legal department,
to standardize the copyright license of our code to
avoid potential copyright risks, we make a unified
modification to the "Hisilicon", which was nonstandard,
in the main modules we maintain.
We change it to "HiSilicon", which is consistent with
the terms used on the following official website:
https://www.hisilicon.com/en/terms-of-use.
Fixes: 565829db8b ("net/hns3: add build and doc infrastructure")
Fixes: 952ebacce4 ("net/hns3: support SVE Rx")
Fixes: e31f123db0 ("net/hns3: support NEON Tx")
Fixes: c09c7847d8 ("net/hns3: support traffic management")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Kunpeng930 support outer UDP cksum, this patch add support for it.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the driver get packet type by parse the
L3_ID/L4_ID/OL3_ID/OL4_ID from Rx descriptor and then lookup multiple
tables, it's time consuming.
Now Kunpeng930 support advanced RXD layout, which:
1. Combine OL3_ID/OL4_ID to 8bit PTYPE filed, so the driver get packet
type by lookup only one table. Note: L3_ID/L4_ID become reserved
fields.
2. The 1588 timestamp located at Rx descriptor instead of query from
firmware.
3. The L3E/L4E/OL3E/OL4E will be zero when L3L4P is zero, so driver
could optimize the good checksum calculations (when L3E/L4E is zero
then mark PKT_RX_IP_CKSUM_GOOD/PKT_RX_L4_CKSUM_GOOD).
Considering compatibility, the firmware will report capability of
RXD advanced layout, the driver will identify and enable it by default.
This patch only provides basic function: identify and enable the RXD
advanced layout, and lookup ptype table if supported.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The normal operation of devices with copper phys depends on the
initialization and configuration of the PHY chip. The task of
driving the PHY chip is implemented in some firmware versions.
If firmware supports the phy driver, it will report a capability
flag to driver in probing process. The driver determines whether
to support PF device with copper phys based on the capability bit.
If supported, the driver set a flag indicating that the firmware
takes over the PHY, and then the firmware initializes the PHY.
This patch supports the query of link status and link info, and
existing basic features for PF device with copper phys.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The configuration operation for PHY is implemented by firmware. And
a capability flag will be report to driver, which means the firmware
supports the PHY driver. However, the current implementation only
supports obtaining the capability bit, but some basic functions of
copper ports in driver, such as, the query of link status and link
info, are not supported.
Therefore, it is necessary for driver to set the copper capability
bit to zero when the firmware supports the configuration of the PHY.
Fixes: 4387523581 ("net/hns3: get device capability from firmware")
Fixes: 95e5032586 ("net/hns3: support copper media type")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
There are two scenarios that command queue uninit performed
concurrently with the firmware command: asynchronous command
and timeout command.
For asynchronous command, if a large number of functions send
commands, these commands may need to be queued to wait for
firmware processing. If a function is uninited suddenly, CMDQ
clearing and firmware processing may be performed concurrently.
For timeout command, if the command failed due to busy scheduling
of firmware, this command will be processed in the next scheduling.
And this may lead to concurrency.
The preceding concurrency may lead to a firmware exceptions.
This patch add a waiting time to ensure the firmware complete the
processing of left over command when PMD uninit.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Replace all the atomic type with C11 atomic builtins in hns3
PMD.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The driver should not use the fixed value as the validity check of
RSS indirection table size with HW supported. As a result, it will
cause misjudgment when the RSS RETA size with HW supported have
changed.
Fixes: c37ca66f2b ("net/hns3: support RSS")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Use errno array instead of switch-case for refactor
the hns3_cmd_convert_err_code function.
Besides, we add a type for ROH(RDMA Over HCCS) check
cmdq return error in Kunpeng930 NIC hardware.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The rte_ethdev_driver.h, rte_ethdev_vdev.h and rte_ethdev_pci.h files are
for drivers only and should be a private to DPDK and not installed.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Steven Webster <steven.webster@windriver.com>
According to the rule of the static check tools
that arrange blank lines properly to keep the
code compact, here remove some unnecessary blank
line to fix the above rule warning.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Some header files have included by others. Also,
some header files have a header file self-contained
error will trigger building warning. As a result,
it is unnecessary and move it into the correct
location.
Beside, here also remove some unused lines.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
The new generation hns3 network engine supports independent enabling and
disabling of a single Tx/Rx queue. So, it can support the queue start
and stop feature. In addition, when different numbers of Tx and Rx
queues need to be enabled in some applications, hns3 pmd does not need
to create fake queues to enable these scenarios.
This patch Add queue start and stop feature for the new generation hns3
networking engine. Cancel the creation of fake queue on the new
generation network engine. And the previously improperly named queue
related function was renamed to improve readability.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Kunpeng 930 hardware support spread packets to region of queues which can
be configured by FDIR rule, it means user can create one FDIR rule which
action is one region of queues, and then RSS use the region info to spread
packets.
As we know, RTE_FLOW_ACTION_TYPE_RSS is used to spread packets among
several queues, user could config such as func/level/types/key/queue
parameter to control RSS function, so we provide this feature under the
RTE_FLOW_ACTION_TYPE_RSS framework.
Consider RSS input tuple don't have eth header, we use the following
rule to distinguish them (whether it's queue region configuration or
rss general configuration):
Case 1: pattern have ETH and action's queue_num > 0, indicate it is
queue region configuration.
Case other: rss general configuration.
So if user want to configure one flow which ipv4=192.168.1.192 spread to
queue region of queue 0/1/2/3, the patter should:
RTE_FLOW_ITEM_TYPE_ETH with spec=last=mask=NULL
RTE_FLOW_ITEM_TYPE_IPV4 with spec=192.168.1.192 last=mask=NULL
RTE_FLOW_ITEM_TYPE_END
the action should:
RTE_FLOW_ACTION_TYPE_RSS with queue_num=4 queue=0/1/2/3
RTE_FLOW_ACTION_TYPE_END
after calling rte_flow_create, one FDIR rule will be created.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds getting device capabilities from firmware, so driver can
supply different capabilities and specifications to upper level
applications base on different versions of hardware network engine.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch modifies the print format for firmware version in the log, It
replaces "0x%08x" with "%lu.%lu.%lu.%lu" in the format control string.
By the way, this patch adds ".fw_version_get" ops implemation for hns3
VF PMD driver.
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, when performing the following test case:
1. Run testpmd application based on hns3 PF device.
2. Inject reset(global/IMP reset) repeatedly.
After the reset, the network port can't link up.
In the RESET_STAGE_DEV_INIT stage of the reset process, the driver will
reinitialize the hardware. If global/IMP reset occurs at this time
again, the operation of reinitialize the hardware will fail because that
firmware don't respond to the configuration commands issued by driver.
In current driver, when failed to reinitialize the hardware, rollback
operation is done, such as clearing the relevant configuration of the
command queue registers.
If firmware detects that the function's command queue register is not
configured correctly, it will not complete the reset related hardware
configuration for this function, resulting in that driver can't detect
that the hardware reset has been completed. And then the reset process
of the driver exit abnormally, the hardware can not work normally after
reset.
This patch fixes it by avoid clearing the command queue related
registers when failed to reinitialize the hardware in the
RESET_STAGE_DEV_INIT stage of the reset process.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Currently, the hns3 PMD driver can interact with firmware through
command to complete hardware configuration. The driver calls internal
interface function named hns3_cmd_send to issues command to the
firmware, and check the execution result of the command through desc_ret
returned by firmware to driver.
As the design of error code, when device is resetting hns3_cmd_send will
only return -EBUSY or -EIO. But we found that if desc_ret is in
[12,65535], for example the item doesn't exist when issuing the command
to query some table item, hns3_cmd_send also return -EIO. This
phenomenon will affect the processing logic for the return value.
The root cause as below:
When desc_ret is in [12,65535], in the static function named
hns3_cmd_convert_err_code called by hns3_cmd_send, matches the default
case and return -EIO. And then hns3_cmd_send return -EIO.
This patch fixes it with the following modification.
1. Change the return value of the default case in the static function
named hns3_cmd_convert_err_code from -EIO to -EREMOTEIO.
2. Modify the comment add errcode description of the internal interface
function named hns3_cmd_send.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Currently, reset related operations can only be performed in the primary
process and are not allowed in the slave process in hns3 PMD driver.
In the internal function interface named hns3_cmd_send used for
communication between driver and firmware, if the wrong head value is
detected in the static subfunction hns3_cmd_csq_clean, driver will
trigger a function level reset to make the hardware work normally again.
This patch adds check condition to prevent triggering reset procedure in
the slave process to avoid failure.
Fixes: 2790c64647 ("net/hns3: support device reset")
Cc: stable@dpdk.org
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
PF FLR resets the PCIe ECAM space of all VFs under the PF
and does not automatically recover. Therefore, the VF driver
needs to restore the ECAM configuration, including
bus_master_en, msix_enable to avoid FLR reset failure.
Fixes: 2790c64647 ("net/hns3: support device reset")
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Configuration commands are sent to firmware for processing.
When firmware processing timeout, the corresponding error
code is returned. Considering that it is more reasonable to
use error code -ETIME for timeout error, the error code for
processing timeout is changed from -EBADE to -ETIME.
Fixes: 737f30e1c3 ("net/hns3: support command interface with firmware")
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
This patch adds reset related process for hns3 PMD driver.
The following three scenarios will trigger the reset process,
and the driver settings will be restored after the reset is
successful:
1. Receive a reset interrupt
2. PF receives a hardware error interrupt
3. VF is notified by PF to reset
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch adds support for mailbox of hns3 PMD driver, mailbox is
used for communication between PF and VF driver.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch adds support for cmd of hns3 PMD driver, driver can interact
with firmware through command to complete hardware configuration.
Signed-off-by: Hao Chen <chenhao164@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Chunsong Feng <fengchunsong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
