The dpdk-test-eventdev tool is a Data Plane Development Kit (DPDK)
application that allows exercising various eventdev use cases. This
application has a generic framework to add new eventdev based test cases
to verify functionality and measure the performance parameters of DPDK
eventdev devices.
This patch adds the skeleton of the dpdk-test-eventdev application.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Harry van Haaren <harry.van.haaren@intel.com>
Currently EAL allocates hugepages one by one not paying attention
from which NUMA node allocation was done.
Such behaviour leads to allocation failure if number of available
hugepages for application limited by cgroups or hugetlbfs and
memory requested not only from the first socket.
Example:
# 90 x 1GB hugepages availavle in a system
cgcreate -g hugetlb:/test
# Limit to 32GB of hugepages
cgset -r hugetlb.1GB.limit_in_bytes=34359738368 test
# Request 4GB from each of 2 sockets
cgexec -g hugetlb:test testpmd --socket-mem=4096,4096 ...
EAL: SIGBUS: Cannot mmap more hugepages of size 1024 MB
EAL: 32 not 90 hugepages of size 1024 MB allocated
EAL: Not enough memory available on socket 1!
Requested: 4096MB, available: 0MB
PANIC in rte_eal_init():
Cannot init memory
This happens beacause all allocated pages are
on socket 0.
Fix this issue by setting mempolicy MPOL_PREFERRED for each hugepage
to one of requested nodes using following schema:
1) Allocate essential hugepages:
1.1) Allocate as many hugepages from numa N to
only fit requested memory for this numa.
1.2) repeat 1.1 for all numa nodes.
2) Try to map all remaining free hugepages in a round-robin
fashion.
3) Sort pages and choose the most suitable.
In this case all essential memory will be allocated and all remaining
pages will be fairly distributed between all requested nodes.
New config option RTE_EAL_NUMA_AWARE_HUGEPAGES introduced and
enabled by default for linuxapp except armv7 and dpaa2.
Enabling of this option adds libnuma as a dependency for EAL.
Fixes: 77988fc08d ("mem: fix allocating all free hugepages")
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Acked-by: Sergio Gonzalez Monroy <sergio.gonzalez.monroy@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Tested-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Move all bypass functions to ixgbe pmd and remove function
pointers from the eth_dev_ops struct.
Signed-off-by: Radu Nicolau <radu.nicolau@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
TX coalescing waits for ETH_COALESCE_PKT_NUM packets to be coalesced
across bursts before transmitting them. For slow traffic, such as
100 PPS, this approach increases latency since packets are received
one at a time and tx coalescing has to wait for ETH_COALESCE_PKT
number of packets to arrive before transmitting.
To fix this:
- Update rx path to use status page instead and only receive packets
when either the ingress interrupt timer threshold (5 us) or
the ingress interrupt packet count threshold (32 packets) fires.
(i.e. whichever happens first).
- If number of packets coalesced is <= number of packets sent
by tx burst function, stop coalescing and transmit these packets
immediately.
Also added compile time option to favor throughput over latency by
default.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Stub callbacks for the generic flow API and a new FLOW debug define.
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Nelson Escobar <neescoba@cisco.com>
When building DPDK with musl, there is need not to disable
backtrace to remove some references to execinfo.h which is
not supported by musl now.
This also applies to some other libc implementation which
doesn't support backtrace() and backtrace_symbols().
musl is an implementation of the userspace portion
of the standard library functionality described in
the ISO C and POSIX standards, plus common extensions.
Got more details about musl from http://www.musl-libc.org .
Signed-off-by: Wei Dai <wei.dai@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Making AVX and AVX512 configurable is useful for performance and power
testing.
The similar kernel patch at https://patchwork.kernel.org/patch/9618883/.
AVX512 support like in rte_memcpy has been in DPDK since 16.04, but it's
still unproven in rich use cases in hardware. Therefore it's marked as
experimental for now, will enable it after enough field test and possible
optimization.
Signed-off-by: Zhihong Wang <zhihong.wang@intel.com>
Reviewed-by: Zhiyong Yang <zhiyong.yang@intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
DPAA2 Hardware Mempool handlers allow enqueue/dequeue from NXP's
QBMAN hardware block.
CONFIG_RTE_MBUF_DEFAULT_MEMPOOL_OPS is set to 'dpaa2', if the pool
is enabled.
This memory pool currently supports packet mbuf type blocks only.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Having packets received without any offload flags given in the mbuf is not
very useful, and performance tests with testpmd indicates little
benefit is got with the current code by turning off the flags. This makes
the build-time option pointless, so we can remove it.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Having packets received without any offload flags given in the mbuf is not
very useful, and performance tests with testpmd indicates little to no
benefit is got with the current code by turning off the flags. This makes
the build-time option pointless, so we can remove it.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Jianbo Liu <jianbo.liu@linaro.org>
Enable Arkville on supported configurations
Add overview documentation
Minimum driver support for valid compile
Arkville PMD is not supported on ARM or PowerPC at this time
Signed-off-by: Ed Czeck <ed.czeck@atomicrules.com>
Signed-off-by: John Miller <john.miller@atomicrules.com>
The crypto scheduler PMD has no external dependencies to enable that by
default.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Declan Doherty <declan.doherty@intel.com>
Add a library designed to calculate latency statistics and report them
to the application when queried. The library measures minimum, average and
maximum latencies, and jitter in nano seconds. The current implementation
supports global latency stats, i.e. per application stats.
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Signed-off-by: Remy Horton <remy.horton@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
This patch adds a library that calculates peak and average data-rate
statistics. For ethernet devices. These statistics are reported using
the metrics library.
Signed-off-by: Remy Horton <remy.horton@intel.com>
This patch adds a new information metrics library. This Metrics
library implements a mechanism by which producers can publish
numeric information for later querying by consumers. Metrics
themselves are statistics that are not generated by PMDs, and
hence are not reported via ethdev extended statistics.
Metric information is populated using a push model, where
producers update the values contained within the metric
library by calling an update function on the relevant metrics.
Consumers receive metric information by querying the central
metric data, which is held in shared memory.
Signed-off-by: Remy Horton <remy.horton@intel.com>
This adds the minimal changes to allow a SW eventdev implementation to
be compiled, linked and created at run time. The eventdev does nothing,
but can be created via vdev on commandline, e.g.
sudo ./x86_64-native-linuxapp-gcc/app/test --vdev=event_sw0
...
PMD: Creating eventdev sw device event_sw0, numa_node=0, sched_quanta=128
RTE>>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Harry van Haaren <harry.van.haaren@intel.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
The skeleton driver facilitates, bootstrapping the new
eventdev driver and creates a platform to verify
the northbound eventdev common code.
The driver supports both VDEV and PCI based eventdev
devices.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
This patch implements northbound eventdev API interface using
southbond driver interface
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Adds a header file with log macros for the AVP PMD
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Signed-off-by: Matt Peters <matt.peters@windriver.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
This commit introduces the AVP PMD file structure without adding any actual
driver functionality. Functional blocks will be added in later patches.
Signed-off-by: Allain Legacy <allain.legacy@windriver.com>
Signed-off-by: Matt Peters <matt.peters@windriver.com>
Acked-by: Vincent Jardin <vincent.jardin@6wind.com>
Add debug options to config file. Define macros used for log and make
use of config file options to enable them.
Signed-off-by: Shijith Thotton <shijith.thotton@caviumnetworks.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Venkat Koppula <venkat.koppula@caviumnetworks.com>
Signed-off-by: Srisivasubramanian S <ssrinivasan@caviumnetworks.com>
Signed-off-by: Mallesham Jatharakonda <mjatharakonda@oneconvergence.com>
Enable Thunderx nicvf PMD driver in the common
config as it does not have build dependency
with any external library and/or architecture.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Add KNI PMD which wraps librte_kni for ease of use.
KNI PMD can be used as any regular PMD to send / receive packets to the
Linux networking stack.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Yong Wang <yongwang@vmware.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Yong Wang <yongwang@vmware.com>
Moved from lib/librte_mempool, stack mempool handler is an independent
driver.
Shared builds would now require to link in librte_mempool_stack for
"stack" mempool handler.
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Moved from lib/librte_mempool, ring mempool is now an independent
driver.
Shared builds would now need to add librte_mempool_ring for:
* ring_mp_mc
* ring_sp_sc
* ring_sp_mc
* ring_mp_sc
Signed-off-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
There was a compile time setting to enable a ring to yield when
it entered a loop in mp or mc rings waiting for the tail pointer update.
Build time settings are not recommended for enabling/disabling features,
and since this was off by default, remove it completely. If needed, a
runtime enabled equivalent can be used.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
The debug option only provided statistics to the user, most of
which could be tracked by the application itself. Remove this as a
compile time option, and feature, simplifying the code.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Users compiling DPDK should not need to know or care about the arrangement
of cachelines in the rte_ring structure. Therefore just remove the build
option and set the structures to be always split. On platforms with 64B
cachelines, for improved performance use 128B rather than 64B alignment
since it stops the producer and consumer data being on adjacent cachelines.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Downstreams might want to provide different DPDK releases at the same
time to support multiple consumers of DPDK linked against older and newer
sonames.
Also due to the interdependencies that DPDK libraries can have applications
might end up with an executable space in which multiple versions of a
library are mapped by ld.so.
Think of LibA that got an ABI bump and LibB that did not get an ABI bump
but is depending on LibA.
Application
\-> LibA.old
\-> LibB.new -> LibA.new
That is a conflict which can be avoided by setting CONFIG_RTE_MAJOR_ABI.
If set CONFIG_RTE_MAJOR_ABI overwrites any LIBABIVER value.
An example might be ``CONFIG_RTE_MAJOR_ABI=16.11`` which will make all
libraries librte<?>.so.16.11 instead of librte<?>.so.<LIBABIVER>.
We need to cut arbitrary long stings after the .so now and this would work
for any ABI version in LIBABIVER:
$(Q)ln -s -f $< $(patsubst %.$(LIBABIVER),%,$@)
But using the following instead additionally allows to simplify the Make
File for the CONFIG_RTE_NEXT_ABI case.
$(Q)ln -s -f $< $(shell echo $@ | sed 's/\.so.*/.so/')
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Reviewed-by: Jan Blunck <jblunck@infradead.org>
Tested-by: Jan Blunck <jblunck@infradead.org>
Remove RTE_LIBRTE_SFC_EFX_TSO config option since it is not
required any more:
- unreasonable limit on number of Tx queues when TSO is not
actually required should be solved using per-device parameter
- performance difference with and without TSO compiled in is small
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
This patchset introduce new application which allows measuring
performance parameters of PMDs available in crypto tree. The goal of
this application is to replace existing performance tests in app/test.
Parameters available are: throughput (--ptest throughput) and latency
(--ptest latency). User can use multiply cores to run tests on but only
one type of crypto PMD can be measured during single application
execution. Cipher parameters, type of device, type of operation and
chain mode have to be specified in the command line as application
parameters. These parameters are checked using device capabilities
structure.
Couple of new library functions in librte_cryptodev are introduced for
application use.
To build the application a CONFIG_RTE_APP_CRYPTO_PERF flag has to be set
(it is set by default).
Example of usage: -c 0xc0 --vdev crypto_aesni_mb_pmd -w 0000:00:00.0 --
--ptest throughput --devtype crypto_aesni_mb --optype cipher-then-auth
--cipher-algo aes-cbc --cipher-op encrypt --cipher-key-sz 16 --auth-algo
sha1-hmac --auth-op generate --auth-key-sz 64 --auth-digest-sz 12
--total-ops 10000000 --burst-sz 32 --buffer-sz 64
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Signed-off-by: Marcin Kerlin <marcinx.kerlin@intel.com>
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Adds Makefile for scheduler cryptodev PMD, and updates existing
Makefiles. Different than other cryptodev PMDs, scheduler PMD
is required to be built as shared libraries.
Adds scheduler PMD enable and debug flags to config/common_base.
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch introduces crypto poll mode driver
using ARMv8 cryptographic extensions.
CPU compatibility with this driver is detected in
run-time and virtual crypto device will not be
created if CPU doesn't provide:
AES, SHA1, SHA2 and NEON.
This PMD is optimized to provide performance boost
for chained crypto operations processing,
such as encryption + HMAC generation,
decryption + HMAC validation. In particular,
cipher only or hash only operations are
not provided.
The driver currently supports AES-128-CBC
in combination with: SHA256 HMAC and SHA1 HMAC
and relies on the external armv8_crypto library:
https://github.com/caviumnetworks/armv8_crypto
Build ARMv8 crypto PMD if compiling for ARM64
and CONFIG_RTE_LIBRTE_PMD_ARMV8_CRYPTO option
is enable in the configuration file.
ARMV8_CRYPTO_LIB_PATH environment variable will
point to the appropriate library directory.
Signed-off-by: Zbigniew Bodek <zbigniew.bodek@caviumnetworks.com>
Reviewed-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Elastic Flow Distributor (EFD) is a distributor library that uses
perfect hashing to determine a target/value for a given incoming flow key.
It has the following advantages:
- First, because it uses perfect hashing, it does not store
the key itself and hence lookup performance is not dependent
on the key size.
- Second, the target/value can be any arbitrary value hence
the system designer and/or operator can better optimize service rates
and inter-cluster network traffic locating.
- Third, since the storage requirement is much smaller than a hash-based
flow table (i.e. better fit for CPU cache), EFD can scale to
millions of flow keys.
Finally, with current optimized library implementation performance
is fully scalable with number of CPU cores.
Signed-off-by: Byron Marohn <byron.marohn@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Signed-off-by: Saikrishna Edupuganti <saikrishna.edupuganti@intel.com>
Acked-by: Christian Maciocco <christian.maciocco@intel.com>
Add PCI device ID for ConnectX-5 and enable multi-packet send for PF and VF
along with changing documentation and release note.
Signed-off-by: Yongseok Koh <yskoh@mellanox.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andrew Lee <alee@solarflare.com>
Reviewed-by: Mark Spender <mspender@solarflare.com>
Reviewed-by: Robert Stonehouse <rstonehouse@solarflare.com>
The PMD allows for DPDK and the host to communicate using a raw
device interface on the host and in the DPDK application. The device
created is a Tap device with a L2 packet header.
Signed-off-by: Keith Wiles <keith.wiles@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Aws Ismail <aismail@ciena.com>
Tested-by: Vasily Philipov <vasilyf@mellanox.com>
Enable the PMD by default on supported configurations.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added API for `rte_eth_tx_prepare`
uint16_t rte_eth_tx_prepare(uint8_t port_id, uint16_t queue_id,
struct rte_mbuf **tx_pkts, uint16_t nb_pkts)
Added fields to the `struct rte_eth_desc_lim`:
uint16_t nb_seg_max;
/**< Max number of segments per whole packet. */
uint16_t nb_mtu_seg_max;
/**< Max number of segments per one MTU */
These fields can be used to create valid packets according to the
following rules:
* For non-TSO packet, a single transmit packet may span up to
"nb_mtu_seg_max" buffers.
* For TSO packet the total number of data descriptors is "nb_seg_max",
and each segment within the TSO may span up to "nb_mtu_seg_max".
Added functions:
int
rte_validate_tx_offload(struct rte_mbuf *m)
to validate general requirements for tx offload set in mbuf of packet
such a flag completness. In current implementation this function is
called optionaly when RTE_LIBRTE_ETHDEV_DEBUG is enabled.
int rte_net_intel_cksum_prepare(struct rte_mbuf *m)
to prepare pseudo header checksum for TSO and non-TSO tcp/udp packets
before hardware tx checksum offload.
- for non-TSO tcp/udp packets full pseudo-header checksum is
counted and set.
- for TSO the IP payload length is not included.
int
rte_net_intel_cksum_flags_prepare(struct rte_mbuf *m, uint64_t ol_flags)
this function uses same logic as rte_net_intel_cksum_prepare, but
allows application to choose which offloads should be taken into
account, if full preparation is not required.
PERFORMANCE TESTS
-----------------
This feature was tested with modified csum engine from test-pmd.
The packet checksum preparation was moved from application to Tx
preparation step placed before burst.
We may expect some overhead costs caused by:
1) using additional callback before burst,
2) rescanning burst,
3) additional condition checking (packet validation),
4) worse optimization (e.g. packet data access, etc.)
We tested it using ixgbe Tx preparation implementation with some parts
disabled to have comparable information about the impact of different
parts of implementation.
IMPACT:
1) For unimplemented Tx preparation callback the performance impact is
negligible,
2) For packet condition check without checksum modifications (nb_segs,
available offloads, etc.) is 14626628/14252168 (~2.62% drop),
3) Full support in ixgbe driver (point 2 + packet checksum
initialization) is 14060924/13588094 (~3.48% drop)
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
There was an option CONFIG_RTE_INSECURE_FUNCTION_WARNING (disabled by
default), which prevents from using some libc functions:
sprintf, snprintf, vsnprintf, strcpy, strncpy, strcat, strncat, sscanf,
strtok, strsep and strlen.
It's all about using them at the right place with the right precautions.
However, it is neither really possible nor a good advice to disable them.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Today, all logs whose level is lower than INFO are dropped at
compile-time. This prevents from enabling debug logs at runtime using
--log-level=8.
The rationale was to remove debug logs from the data path at
compile-time, avoiding a test at run-time.
This patch changes the behavior of RTE_LOG() to avoid the compile-time
optimization, and introduces the RTE_LOG_DP() macro that has the same
behavior than the previous RTE_LOG(), for the rare cases where debug
logs are in the data path.
So it is now possible to enable debug logs at run-time by just
specifying --log-level=8. Some drivers still have special compile-time
options to enable more debug log. Maintainers may consider to
remove/reduce them.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
- Fix to use bitmapped values in NVM configuration for speed capability
advertisement. This issue is specific to 25G NIC since it is capable
of 25G and 10G speeds.
- Update feature list.
Fixes: 64c239b7f8 ("net/qede: fix advertising link speed capability")
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
This patch replaces name "libcrypto" to "openssl" from file directories,
symbol prefixes and sub-names connected with old name.
Renamed poll mode driver files, test files, and documentations.
It is done to better name association with library because
the cryptography operations are using Openssl library crypto API.
Fixes: d61f70b4c9 ("crypto/libcrypto: add driver for OpenSSL library")
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
The QEDE PMD now uses unzipped firmware file eliminating the dependency
on zlib. Hence remove LDLIBS entry form the Makefile and enable qede
PMD by default.
Fixes: 6adac0bf30 ("qede: add missing external dependency and disable by default")
Signed-off-by: Rasesh Mody <rasesh.mody@qlogic.com>
Since switched to kernel dynamic debugging it is possible to remove
compile time debug log configuration.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
This code provides the initial implementation of the libcrypto
poll mode driver. All cryptography operations are using Openssl
library crypto API. Each algorithm uses EVP_ interface from
openssl API - which is recommended by Openssl maintainers.
This patch adds libcrypto poll mode driver support to librte_cryptodev
library.
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Signed-off-by: Michal Kobylinski <michalx.kobylinski@intel.com>
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Signed-off-by: Daniel Mrzyglod <danielx.t.mrzyglod@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Added new SW PMD which makes use of the libsso SW library,
which provides wireless algorithms ZUC EEA3 and EIA3
in software.
This PMD supports cipher-only, hash-only and chained operations
("cipher then hash" and "hash then cipher") of the following
algorithms:
- RTE_CRYPTO_SYM_CIPHER_ZUC_EEA3
- RTE_CRYPTO_SYM_AUTH_ZUC_EIA3
The ZUC hash and cipher algorithms, which are enabled
by this crypto PMD are implemented by Intel's libsso software
library.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
remove vhost-cuse code, including the eventfd_link kernel module that
is for vhost-cuse only.
The lib/virt/qemu-wrap.py is also removed, as it's mainly for vhost-cuse
usage.
As we have one vhost implementation now, one vhost config option is
needed only. Thus, CONFIG_RTE_LIBRTE_VHOST_USER is removed.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
With current config structure, all configuration parameters put into
common_base with a default value, and overwritten in environment file
if required, CONFIG_RTE_VIRTIO_USER is missing in common_base.
This fix is simple, by adding CONFIG_RTE_VIRTIO_USER=n as the default
macro value.
Fixes: ce2eabdd43 ("net/virtio-user: add virtual device")
Reported-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Inline TX will be fully managed by the PMD after Verbs is bypassed in the
data path. Remove the current code until then.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
There is no scatter/gather support anymore, CONFIG_RTE_LIBRTE_MLX5_SGE_WR_N
has no purpose and can be removed.
Signed-off-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
- Add device id to the PCI table
- Add polling for the slowpath events for CMT mode device
- Add prerequisites to allow 100g mode
* Min number of queues needed is 2
* Only even number of queues are allowed
- Update documentation
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Introduce driver initialization and enable build infrastructure for
nicvf pmd driver.
By default, It is enabled only for defconfig_arm64-thunderx-*
config as it is an inbuilt NIC device.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
This patch adds the initial skeleton for bnxt driver along with the
nic guide, and ties the driver into the build system.
At this point, the driver simply fails init.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
[Release Note Addition]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
By default, the mempool ops used for mbuf allocations is a multi
producer and multi consumer ring. We could imagine a target (maybe some
network processors?) that provides an hardware-assisted pool
mechanism. In this case, the default configuration for this architecture
would contain a different value for RTE_MBUF_DEFAULT_MEMPOOL_OPS.
Signed-off-by: David Hunt <david.hunt@intel.com>
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Jan Viktorin <viktorin@rehivetech.com>
Acked-by: Shreyansh Jain <shreyansh.jain@nxp.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Added new SW PMD which makes use of the libsso_kasumi SW library,
which provides wireless algorithms KASUMI F8 and F9
in software.
This PMD supports cipher-only, hash-only and chained operations
("cipher then hash" and "hash then cipher") of the following
algorithms:
- RTE_CRYPTO_SYM_CIPHER_KASUMI_F8
- RTE_CRYPTO_SYM_AUTH_KASUMI_F9
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
The librte_pdump library provides a framework for
packet capturing in dpdk. The library provides set of
APIs to initialize the packet capture framework, to
enable or disable the packet capture, and to uninitialize
it.
The librte_pdump library works on a client/server model.
The server is responsible for enabling or disabling the
packet capture and the clients are responsible
for requesting the enabling or disabling of the packet
capture.
Enabling APIs are supported with port, queue, ring and
mempool parameters. Applications should pass on this information
to get the packets from the dpdk ports.
For enabling requests from applications, library creates the client
request containing the mempool, ring, port and queue information and
sends the request to the server. After receiving the request, server
registers the Rx and Tx callbacks for all the port and queues.
After the callbacks registration, registered callbacks will get the
Rx and Tx packets. Packets then will be copied to the new mbufs that
are allocated from the user passed mempool. These new mbufs then will
be enqueued to the application passed ring. Applications need to dequeue
the mbufs from the rings and direct them to the devices like
pcap vdev for viewing the packets outside of the dpdk
using the packet capture tools.
For disabling requests, library creates the client request containing
the port and queue information and sends the request to the server.
After receiving the request, server removes the Rx and Tx callback
for all the port and queues.
Signed-off-by: Reshma Pattan <reshma.pattan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The commit 66819e6 has introduced a dependency on libarchive to be able
to use some tar resources in the unit tests.
It is now an optional dependency because some systems do not have it
installed.
If CONFIG_RTE_APP_TEST_RESOURCE_TAR is disabled, the PCI test will not
be run. When a "configure" script will be integrated, the libarchive
availability could be checked to automatically enable the option.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Reviewed-by: Jan Viktorin <viktorin@rehivetech.com>
The qede driver depends on libz but the LDLIBS entry in makefile
was missing. Also because of the external dependency, make it
disabled in default config as per common DPDK policy on external deps.
Fixes: ec94dbc573 ("qede: add base driver")
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The default was to compile every logs (including debug) and set
the default level to debug.
As some debug logs may hurt performance, a notice is added and the
default level is now info.
In order to enable debug logs, they must be compiled with
RTE_LOG_LEVEL=RTE_LOG_DEBUG and enabled at runtime with --log-level=8.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
The driver i40e was using a specific PCI config before the release 16.04.
Since 16.04, it is always enabled in i40e (commit 56465cfaf).
The API has been deprecated in the commit 68f7759382.
The igb_uio implementation has been deprecated in commit b7cf8e155.
The config helper - through igb_uio sysfs entries - is now removed.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: David Marchand <david.marchand@6wind.com>
The cryptodev API was introduced in the DPDK 2.2 release.
Since then it has
- been reviewed and iterated for the DPDK 16.04 release
- had extensive use by the l2fwd-crypto app,
the ipsec-secgw example app,
the test app.
We believe it is now stable and the EXPERIMENTAL label should be removed.
Signed-off-by: Fiona Trahe <fiona.trahe@intel.com>
Acked-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Previously, vector driver is not the first (default) choice for i40e,
as it cannot fill packet type info for l3fwd to work well. Now there
is an option for l3fwd to analysis packet type softly. So enable it
by default.
Signed-off-by: Jianfeng Tan <jianfeng.tan@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
The patch introduces a new PMD. This PMD is implemented as thin wrapper
of librte_vhost. It means librte_vhost is also needed to compile the PMD.
The vhost messages will be handled only when a port is started. So start
a port first, then invoke QEMU.
The PMD has 2 parameters.
- iface: The parameter is used to specify a path to connect to a
virtio-net device.
- queues: The parameter is used to specify the number of the queues
virtio-net device has.
(Default: 1)
Here is an example.
$ ./testpmd -c f -n 4 --vdev 'eth_vhost0,iface=/tmp/sock0,queues=1' -- -i
To connect above testpmd, here is qemu command example.
$ qemu-system-x86_64 \
<snip>
-chardev socket,id=chr0,path=/tmp/sock0 \
-netdev vhost-user,id=net0,chardev=chr0,vhostforce,queues=1 \
-device virtio-net-pci,netdev=net0,mq=on
Signed-off-by: Tetsuya Mukawa <mukawa@igel.co.jp>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Rich Lane <rich.lane@bigswitch.com>
Tested-by: Rich Lane <rich.lane@bigswitch.com>
Update for queue state event name:
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
This is a PMD for the Amazon ethernet ENA (Elastic Network Adapters)
family.
The driver operates variety of ENA adapters through feature negotiation
with the adapter and upgradable commands set.
ENA driver handles PCI Physical and Virtual ENA functions.
Signed-off-by: Evgeny Schemeilin <evgenys@amazon.com>
Signed-off-by: Jan Medala <jan@semihalf.com>
Signed-off-by: Jakub Palider <jpa@semihalf.com>
Release Note addition:
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Mmap PCI resource file and add inline functions for reading from and
writing to PCI resource address space.
Add description of IBUF and OBUF address space.
Add configuration option for setting which firmware type will be used.
Right address space values for IBUFs and OBUFs offsets are used
according to configuration option CONFIG_RTE_LIBRTE_PMD_SZEDATA2_AS.
Setting link up/down and getting info about link status is done through
mmapped PCI resource address space.
Signed-off-by: Matej Vido <vido@cesnet.cz>
Originally, source ports in librte_port is an input port used as packet
generator. Similar to Linux kernel /dev/zero character device, it
generates null packets. This patch adds optional PCAP file support to
source port: instead of sending NULL packets, the source port generates
packets copied from a PCAP file. To increase the performance, the packets
in the file are loaded to memory initially, and copied to mbufs in circular
manner. Users can enable or disable this feature by setting
CONFIG_RTE_PORT_PCAP compiler option "y" or "n".
Signed-off-by: Fan Zhang <roy.fan.zhang@intel.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Parse the device parameters from rte_eal_vdev_init,
instead of the config file, so user can change the parameters
at runtime.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
This patch provides the implementation of a NULL crypto PMD, which supports
NULL cipher and NULL authentication operations, which can be chained together
as follows:
- Authentication Only
- Cipher Only
- Authentication then Cipher
- Cipher then Authentication
As this is a NULL operation device the crypto operations which are submitted for
processing are not actually modified and are stored in a queue pairs processed
packets ring ready for collection when rte_cryptodev_burst_dequeue() is called.
The patch also contains the related unit tests function to test the PMDs
supported operations.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
This patch provides the implementation of an AES-NI accelerated crypto PMD
which is dependent on Intel's multi-buffer library, see the white paper
"Fast Multi-buffer IPsec Implementations on Intel® Architecture Processors"
This PMD supports AES_GCM authenticated encryption and authenticated
decryption using 128-bit AES keys
The patch also contains the related unit tests functions
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John Griffin <john.griffin@intel.com>
Added new SW PMD which makes use of the libsso SW library,
which provides wireless algorithms SNOW 3G UEA2 and UIA2
in software.
This PMD supports cipher-only, hash-only and chained operations
("cipher then hash" and "hash then cipher") of the following
algorithms:
- RTE_CRYPTO_SYM_CIPHER_SNOW3G_UEA2
- RTE_CRYPTO_SYM_AUTH_SNOW3G_UIA2
The SNOW 3G hash and cipher algorithms, which are enabled
by this crypto PMD are implemented by Intel's libsso software
library. For library download and build instructions,
see the documentation included (doc/guides/cryptodevs/snow3g.rst)
The patch also contains the related unit tests function to test the PMD
supported operations.
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
As cryptodev library does not depend on mbuf_offload library
any longer, this patch removes it.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Acked-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: Deepak Kumar Jain <deepak.k.jain@intel.com>
Remove pci configuration of 'extended tag' and 'max read request
size', as they are not required by all devices and it lets PMD to
configure them if necessary.
In addition, 'pci_config_space_set()' is deprecated.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
In order to cleanup the configuration files some and reduce
the number of duplicate configuration information. Add a new
file called common_base which contains just about all of the
configuration lines in one place. Then have the common_bsdapp,
common_linuxapp files include this one file. Then in those OS
specific files add the delta configuration lines.
Signed-off-by: Keith Wiles <keith.wiles@intel.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
