Removing 'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag.
Instead of drivers announce this capability, application can deduct the
capability by checking reported 'dev_info.max_mtu' or
'dev_info.max_rx_pktlen'.
And instead of application setting this flag explicitly to enable jumbo
frames, this can be deduced by driver by comparing requested 'mtu' to
'RTE_ETHER_MTU'.
Removing this additional configuration for simplification.
Suggested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Michal Krawczyk <mk@semihalf.com>
There is a confusion on setting max Rx packet length, this patch aims to
clarify it.
'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.
Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.
These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.
Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.
As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.
For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.
When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.
Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Definition of `rte_ether_addr` structure used a workaround allowing DPDK
and Windows SDK headers to be used in the same file, because Windows SDK
defines `s_addr` as a macro. Rename `s_addr` to `src_addr` and `d_addr`
to `dst_addr` to avoid the conflict and remove the workaround.
Deprecation notice:
https://mails.dpdk.org/archives/dev/2021-July/215270.html
Signed-off-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
Copy threshold has been introduced in async vhost data
path to select the appropriate copy engine to do copies
for higher efficiency.
However, it may cause packets ordering issues and also
introduces performance unpredictability.
Therefore, this patch removes copy threshold support in
async vhost data path.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Added macros to simplify print of MAC address.
The six bytes of a MAC address are extracted in
a macro here, to improve code readablity.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added macro to print six bytes of MAC address.
The MAC addresses will be printed in upper case
hexadecimal format.
In case there is a specific check for lower case
MAC address, the user may need to make a change in
such test case after this patch.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
When the guest memory is hotplugged, the vhost application which
enables DMA acceleration must stop DMA transfers before the vhost
re-maps the guest memory.
To accomplish that, we need to do these changes in the vhost sample:
1. add inflight packets count.
2. add vring_state_changed() callback.
3. add inflight packets clear process in destroy_device() and
vring_state_changed().
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch reworks the async configuration structure to improve code
readability. In addition, add preserved padding fields on the structure
for future usage.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
The vhost library currently configures Tx offloading (PKT_TX_*) on any
packet received from a guest virtio device which asks for some offloading.
This is problematic, as Tx offloading is something that the application
must ask for: the application needs to configure devices
to support every used offloads (ip, tcp checksumming, tso..), and the
various l2/l3/l4 lengths must be set following any processing that
happened in the application itself.
On the other hand, the received packets are not marked wrt current
packet l3/l4 checksumming info.
Copy virtio rx processing to fix those offload flags with some
differences:
- accept VIRTIO_NET_HDR_GSO_ECN and VIRTIO_NET_HDR_GSO_UDP,
- ignore anything but the VIRTIO_NET_HDR_F_NEEDS_CSUM flag (to comply with
the virtio spec),
Some applications might rely on the current behavior, so it is left
untouched by default.
A new RTE_VHOST_USER_NET_COMPLIANT_OL_FLAGS flag is added to enable the
new behavior.
The vhost example has been updated for the new behavior: TSO is applied to
any packet marked LRO.
Fixes: 859b480d5afd ("vhost: add guest offload setting")
Cc: stable@dpdk.org
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
According to the programming guide, the rte_eal_init should be used pairs
with rte_eal_cleanup.
This patch add rte_eal_cleanup to examples to encourage new users of
DPDK to use it.
Fixes: aec9c13c5257 ("eal: add function to release internal resources")
Fixes: 3d0fad56b74a ("examples/fips_validation: add crypto FIPS application")
Fixes: c8e6ceecebc1 ("examples/ioat: add new sample app for ioat driver")
Fixes: 4ff457986f76 ("examples/l2fwd-event: add default poll mode routines")
Fixes: 08bd1a174461 ("examples/l3fwd-graph: add graph-based l3fwd skeleton")
Fixes: c5eebf85badc ("examples/ntb: add example for NTB")
Fixes: b77f66002812 ("examples/pipeline: add new example application")
Fixes: edbed86d1cc3 ("examples/vdpa: introduce a new sample for vDPA")
Fixes: c19beb3f38cd ("examples/vhost_blk: introduce vhost storage sample")
Fixes: f5188211c721 ("examples/vhost_crypto: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Instead of using getopt_long return value, strcmp was used to
compare the input parameters with the struct option array. This
patch get rid of all those strcmp by directly binding each longopt
with an int enum. This is to improve readability and consistency in
all examples.
Bugzilla ID: 238
Reported-by: David Marchand <david.marchand@redhat.com>
Signed-off-by: Ibtisam Tariq <ibtisam.tariq@emumba.com>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Change the type of buff_idx from uint64_t to uint32_t to fix coverity
issue.
Coverity issue: 366264
Fixes: a68ba8e0a6b6 ("examples/vhost: refactor vhost data path")
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Remove async inflight packet counter since there is no need to keep
tracking it. Increase MAX_ENQUEUED_SIZE to prevent packet segment number
tracking ring from being exhausted.
Fixes: a68ba8e0a6b6 ("examples/vhost: refactor vhost data path")
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Change the vm2vm data path to batch enqueue for better performance.
Support latest async vhost API, refactor vhost async data path,
replace rte_atomicNN_xxx to __atomic_XXX and clean some codes.
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Jiayu Hu <jiayu.hu@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Async enqueue offloads large copies to DMA devices, and small copies
are still performed by the CPU. However, it requires users to get
enqueue completed packets by rte_vhost_poll_enqueue_completed(), even
if they are completed by the CPU when rte_vhost_submit_enqueue_burst()
returns. This design incurs extra overheads of tracking completed
pktmbufs and function calls, thus degrading performance on small packets.
This patch enhances async enqueue for small packets by enabling
rte_vhost_submit_enqueue_burst() to return completed packets.
Signed-off-by: Jiayu Hu <jiayu.hu@intel.com>
Tested-by: Yinan Wang <yinan.wang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Fix vhost-switch compiling issue when ioat dependency is missing.
Change 'RTE_x86' check into 'RTE_RAW_IOAT' check in meson build file.
Use 'RTE_RAW_IOAT' to control conditional compiling in source file.
Clean some codes.
Fixes: abec60e7115d ("examples/vhost: support vhost async data path")
Fixes: 3a04ecb21420 ("examples/vhost: add async vhost args parsing")
Reported-by: David Marchand <david.marchand@redhat.com>
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Tested-by: David Marchand <david.marchand@redhat.com>
This patch is to implement vhost DMA operation callbacks for CBDMA
PMD and add vhost async data-path in vhost sample. With providing
callback implementation for CBDMA, vswitch can leverage IOAT to
accelerate vhost async data-path.
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This patch is to add async vhost driver arguments parsing function
for CBDMA channel, DMA initiation function and args description.
The meson build file is changed to fix dependency problem. With
these arguments vhost device can be set to use CBDMA or CPU for
enqueue operation and bind vhost device with specific CBDMA channel
to accelerate data copy.
Signed-off-by: Cheng Jiang <cheng1.jiang@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Replace master lcore with main lcore and
replace slave lcore with worker lcore.
Keep the old functions and macros but mark them as deprecated
for this release.
The "--master-lcore" command line option is also deprecated
and any usage will print a warning and use "--main-lcore"
as replacement.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Dequeue zero-copy feature is being removed from the
Vhost library. This preliminary patch removes its uses
in the Vhost example application.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Chenbo Xia <chenbo.xia@intel.com>
Giving invalid or zero portmask as command line option to
these applications will have an unexpected response.
The reason behind this is that the return value of function
that parses portmask is stored in a variable whose datatype is
unsigned int, hence returning -1 in case of zero or
invalid portmask causes an unexpected behaviour.
If we return 0 instead of -1 this issue can be resolved.
The program already contains the functionality to print
"invalid portmask" and program usage if zero is returned.
Signed-off-by: Sarosh Arif <sarosh.arif@emumba.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
When printf()'s stdout is line-buffered for terminal, it is fully
buffered for pipes. So, stdout listener can only get the output
when it is flushed (on program termination, when buffer is filled or
manual flush).
stdout buffer might fill slowly since every stats report could be small.
Also when it is fully filled it might contain a part of the last stats
report which makes it very inconvenient for any automation which reads
and parses the output.
Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Signed-off-by: Georgiy Levashov <georgiy.levashov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The return value of rte_eth_macaddr_get() was changed from void to int.
Update the usage of the functions according to the new return type.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
rte_eth_promiscuous_enable()/rte_eth_promiscuous_disable() return
value was changed from void to int, so this patch modify usage
of these functions across examples according to new return type.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
rte_eth_dev_info_get() return value was changed from void to
int, so this patch modify rte_eth_dev_info_get() usage across
examples/vhost according to its new return type.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
Since we change these macros, we might as well avoid triggering complaints
from checkpatch because of mixed case.
old=RTE_IPv4
new=RTE_IPV4
git grep -lw $old | xargs sed -i -e "s/\<$old\>/$new/g"
old=RTE_ETHER_TYPE_IPv4
new=RTE_ETHER_TYPE_IPV4
git grep -lw $old | xargs sed -i -e "s/\<$old\>/$new/g"
old=RTE_ETHER_TYPE_IPv6
new=RTE_ETHER_TYPE_IPV6
git grep -lw $old | xargs sed -i -e "s/\<$old\>/$new/g"
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Olivier Matz <olivier.matz@6wind.com>
Add 'RTE_' prefix to defines:
- rename ETHER_ADDR_LEN as RTE_ETHER_ADDR_LEN.
- rename ETHER_TYPE_LEN as RTE_ETHER_TYPE_LEN.
- rename ETHER_CRC_LEN as RTE_ETHER_CRC_LEN.
- rename ETHER_HDR_LEN as RTE_ETHER_HDR_LEN.
- rename ETHER_MIN_LEN as RTE_ETHER_MIN_LEN.
- rename ETHER_MAX_LEN as RTE_ETHER_MAX_LEN.
- rename ETHER_MTU as RTE_ETHER_MTU.
- rename ETHER_MAX_VLAN_FRAME_LEN as RTE_ETHER_MAX_VLAN_FRAME_LEN.
- rename ETHER_MAX_VLAN_ID as RTE_ETHER_MAX_VLAN_ID.
- rename ETHER_MAX_JUMBO_FRAME_LEN as RTE_ETHER_MAX_JUMBO_FRAME_LEN.
- rename ETHER_MIN_MTU as RTE_ETHER_MIN_MTU.
- rename ETHER_LOCAL_ADMIN_ADDR as RTE_ETHER_LOCAL_ADMIN_ADDR.
- rename ETHER_GROUP_ADDR as RTE_ETHER_GROUP_ADDR.
- rename ETHER_TYPE_IPv4 as RTE_ETHER_TYPE_IPv4.
- rename ETHER_TYPE_IPv6 as RTE_ETHER_TYPE_IPv6.
- rename ETHER_TYPE_ARP as RTE_ETHER_TYPE_ARP.
- rename ETHER_TYPE_VLAN as RTE_ETHER_TYPE_VLAN.
- rename ETHER_TYPE_RARP as RTE_ETHER_TYPE_RARP.
- rename ETHER_TYPE_QINQ as RTE_ETHER_TYPE_QINQ.
- rename ETHER_TYPE_ETAG as RTE_ETHER_TYPE_ETAG.
- rename ETHER_TYPE_1588 as RTE_ETHER_TYPE_1588.
- rename ETHER_TYPE_SLOW as RTE_ETHER_TYPE_SLOW.
- rename ETHER_TYPE_TEB as RTE_ETHER_TYPE_TEB.
- rename ETHER_TYPE_LLDP as RTE_ETHER_TYPE_LLDP.
- rename ETHER_TYPE_MPLS as RTE_ETHER_TYPE_MPLS.
- rename ETHER_TYPE_MPLSM as RTE_ETHER_TYPE_MPLSM.
- rename ETHER_VXLAN_HLEN as RTE_ETHER_VXLAN_HLEN.
- rename ETHER_ADDR_FMT_SIZE as RTE_ETHER_ADDR_FMT_SIZE.
- rename VXLAN_GPE_TYPE_IPV4 as RTE_VXLAN_GPE_TYPE_IPV4.
- rename VXLAN_GPE_TYPE_IPV6 as RTE_VXLAN_GPE_TYPE_IPV6.
- rename VXLAN_GPE_TYPE_ETH as RTE_VXLAN_GPE_TYPE_ETH.
- rename VXLAN_GPE_TYPE_NSH as RTE_VXLAN_GPE_TYPE_NSH.
- rename VXLAN_GPE_TYPE_MPLS as RTE_VXLAN_GPE_TYPE_MPLS.
- rename VXLAN_GPE_TYPE_GBP as RTE_VXLAN_GPE_TYPE_GBP.
- rename VXLAN_GPE_TYPE_VBNG as RTE_VXLAN_GPE_TYPE_VBNG.
- rename ETHER_VXLAN_GPE_HLEN as RTE_ETHER_VXLAN_GPE_HLEN.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add 'rte_' prefix to structures:
- rename struct ether_addr as struct rte_ether_addr.
- rename struct ether_hdr as struct rte_ether_hdr.
- rename struct vlan_hdr as struct rte_vlan_hdr.
- rename struct vxlan_hdr as struct rte_vxlan_hdr.
- rename struct vxlan_gpe_hdr as struct rte_vxlan_gpe_hdr.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
For files that already have rte_string_fns.h included in them, we can
do a straight replacement of snprintf(..."%s",...) with strlcpy. The
changes in this patch were auto-generated via command:
spatch --sp-file devtools/cocci/strlcpy-with-header.cocci --dir . --in-place
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Add the missing failure handling for path allocation,
as realloc() may fail.
Fixes: ad0eef4d2203 ("examples/vhost: support multiple socket files")
Cc: stable@dpdk.org
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
This minor patch fixes a typo in examples/vhost/main.c.
Fixes: d19533e86f1d ("examples/vhost: copy old vhost example")
Cc: stable@dpdk.org
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Reviewed-by: Gavin Hu <gavin.hu@arm.com>
This cleanup patch removes a method and a constant which
are now unnecessary in the VHOST sample application, namely
the validate_num_devices() method and the MAX_DEVICES
constant.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Removed DEV_RX_OFFLOAD_CRC_STRIP offload flag.
Without any specific Rx offload flag, default behavior by PMDs is to
strip CRC.
PMDs that support keeping CRC should advertise DEV_RX_OFFLOAD_KEEP_CRC
Rx offload capability.
Applications that require keeping CRC should check PMD capability first
and if it is supported can enable this feature by setting
DEV_RX_OFFLOAD_KEEP_CRC in Rx offload flag in rte_eth_dev_configure()
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tomasz Duszynski <tdu@semihalf.com>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Acked-by: Jan Remes <remes@netcope.com>
Acked-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
This patch removes an unnecessary definition of MAX_PRINT_BUFF
in examples/vhost/main.c, since it is no longer being used.
Fixes: 68363d85857d ("examples/vhost: remove the non-working zero copy code")
Cc: stable@dpdk.org
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Reviewed-by: Tiwei Bie <tiwei.bie@intel.com>
In DPDK 17.11, the ethdev offloads API has changed:
commit cba7f53b717d ("ethdev: introduce Tx queue offloads API")
commit ce17eddefc20 ("ethdev: introduce Rx queue offloads API")
The new API is documented in the programmer's guide:
http://doc.dpdk.org/guides/prog_guide/poll_mode_drv.html#hardware-offload
For reminder, the main concepts in the new API were:
- All offloads are disabled by default
- Distinction between per port and per queue offloads.
The transition bits are now removed:
- Translation of the old API in ethdev
- rte_eth_conf.rxmode.ignore_offload_bitfield
- ETH_TXQ_FLAGS_IGNORE
The old API bits are now removed:
- Rx per-port rte_eth_conf.rxmode.[bit-fields]
- Tx per-queue rte_eth_txconf.txq_flags
- ETH_TXQ_FLAGS_NO*
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Shahaf Shuler <shahafs@mellanox.com>
A new API was introduced to create control thread:
rte_ctrl_thread_create(). Use it in examples when relevant.
While at it, change the prototype of the thread start functions: it's
not a good idea to cast it in (void *) since the compiler won't check
that the prototype is compatible.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Only a cosmetic change: the *_LEN defines are already used
when defining the buffer. Using sizeof() ensures that the length
stays consistent, even if the definition is modified.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Anatoly Burakov <anatoly.burakov@intel.com>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
In order to fix this common mistake in all external applications,
the function rte_eth_dev_count is deprecated, while introducing
the new functions rte_eth_dev_count_avail and rte_eth_dev_count_total.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application assume a valid port index is in the range [0..count[.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be valid
- old ports being detached (RTE_ETH_DEV_UNUSED) can be valid
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the function rte_eth_dev_is_valid_port.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be seen
- old ports being detached (RTE_ETH_DEV_UNUSED) can be seen as ghosts
- failsafe sub-devices (RTE_ETH_DEV_DEFERRED) will be seen by the application
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the iterator RTE_ETH_FOREACH_DEV.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
For vhost sample, the operation if (dev_info.max_rx_queues >
MAX_QUEUES) in the function port_init causes startup failure
when using X710(i40e driver). X710 requires that MAX_QUEUES
should be defined no less than 320, however it is defined as
128 currently.
Such checking is overkill and Removal don't affect any
functionality (have already validated ixgbe and i40e).
The removal can avoid similar issue when introduing new physical NIC.
Fixes: 8bd6c395a568 ("examples/vhost: increase maximum queue number")
Cc: stable@dpdk.org
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Yuanhan Liu <yliu@fridaylinux.org>
ARP packets are not dropped when dest vdev is itself, which breaks
RX ring inconspicuously.
Fixes: 9c5ef51207c6 ("examples/vhost: handle broadcast packet")
Cc: stable@dpdk.org
Signed-off-by: Junjie Chen <junjie.j.chen@intel.com>
Acked-by: Yuanhan Liu <yliu@fridaylinux.org>
Replace the BSD license header with the SPDX tag for files
with only an Intel copyright on them.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Extend port_id definition from uint8_t to uint16_t in lib and drivers
data structures, specifically rte_eth_dev_data. Modify the APIs,
drivers and app using port_id at the same time.
Fix some checkpatch issues from the original code and remove some
unnecessary cast operations.
release_17_11 and deprecation docs have been updated in this patch.
Signed-off-by: Zhiyong Yang <zhiyong.yang@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
