Several structures and macros are added or updated, such
as 'struct i40e_aqc_get_link_status',
'struct i40e_aqc_run_phy_activity' and
'struct i40e_aqc_lldp_set_local_mib_resp'.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
It adds the new AQ command and struct for managing a
thermal sensor.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
X722 supports Expanded version of TCP, UDP PCTYPES for RSS.
Add a Virtchnl offload to support this.
Without this patch VF drivers will not be able to support
the correct PCTYPES for X722 and UDP flows will not fan out.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds 7 new register definitions for programming the
parser, flow director and RSS blocks in the HW.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
RX control register read/write functions are added, as directly
read/write may fail when under stress small traffic. After the
adminq is ready, all rx control registers should be read/written
by dedicated functions.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
When updating a VSI, save off the number of allocated and
unallocated VSIs as we do when adding a VSI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Fix the driver load failure with linking with some
PHY types, as the amount of time it takes for the
GLGEN_RSTAT_DEVSTATE to be set increases greatly on those PHY
types, which can lead to a timeout.
Fixes: 9aeefed05538 ("i40e/base: support ESS")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In Multi-Function Mode (MFP) particularly when the PF VSI is set
in limited promiscuous mode, the HW switch was still mirroring the
outgoing packets from other VSIs (VF/VMdq) onto the PF VSI.
This sets a new bit to avoid above mirroring, and it is in limited
promiscuous on the PF VSI in MFP which is similar to default port
VSI.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch adds functions to blink led on devices using a new
PHY since MAC registers used in other designs do not work in
this device configuration.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add the support code for calling the AdminQ API call
aq_set_switch_config.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
With the latest firmware, statistics gathering can now be enabled and
disabled in the HW switch, so we need to add a parameter to allow the
driver to set it as desired. At the same time, the L2 cloud filtering
parameter has been removed as it was never used.
Older drivers working with the newer firmware and newer drivers working
with older firmware will not run into problems with these bits as the
defaults are reasonable and there is no overlap in the bit definitions.
Also, newer drivers will be forced to update because of the change in
function call parameters, a reminder that the functionality exists.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch implements necessary functions related to port
mirroring features such as add/delete mirror rule, function
to set promiscuous VLAN mode for VSI if mirror rule_type is
"VLAN Mirroring".
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add the use of the new shared MAC filter bit for multicast
and broadcast filters in order to make better use of the
filters available from the device.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This patch fixes a problem where the NVMUpdate Tool, when
using the PHY NVM feature, gets bad data from the PHY because
of contention on the MDIO interface from get phy capability
calls from the driver during regular operations. The problem
is fixed by adding a check if media is available before calling
get phy capability function because that bit is not set when
device is in PHY interaction mode.
Fixes: 842ea1996335 ("i40e/base: save link module type")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The device capabilities were defined in two places, and neither had
all the definitions. It really belongs with the AQ API definition,
so this patch removes the other set of definitions and fills out the
missing item.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The recently added proxy opcodes should be available only with
X722_SUPPORT, so move them into the #ifdef, and reorder these
to be in numerical order with the rest of the opcodes. Several
structs that were added are unnecessary, so they are removed
here.
Fixes: 788fc17b2dec ("i40e/base: support proxy config for X722")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The recently added Wakeup On Line (WOL) opcodes should be
available only with X722_SUPPORT, so move them into the #ifdef,
and reorder these to be in numerical order with the rest of the
opcodes. Several structs that were added are unnecessary, so
they are removed here.
Fixes: 3c89193a36fd ("i40e/base: support WOL config for X722")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Add new Device ID's for backplane and QSFP+ adapters, and delete
deprecated one for backplane.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In one obscure corner case, it was possible to clear the NVM update
wait flag when no update_done message was actually received. This
patch cleans the event descriptor before use, and moves the opcode
check to where it won't get done if there was no event to clean.
Fixes: 8db9e2a1b232 ("i40e: base driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
The standard way to check if the AQ is enabled is to look at
the count field. So it should only set this field after it has
successfully allocated memory.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
It's possible that while waiting for the spinlock, another
entity (that owns the spinlock) has shut down the admin queue.
If it then attempts to use the queue, it will panic.
It adds a check for this condition on the receive side. This
matches an existing check on the send queue side.
Fixes: 8db9e2a1b232 ("i40e: base driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
XL710/X710 devices requires FW version checks to properly handle
DCB configurations from the FW while other devices (e.g. X722)
do not, so limit these checks to XL710/X710 only.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
In X722, NVM reads can't be done through SRCTL registers.
And require AQ calls, which require grabbing the NVM lock.
Unfortunately some paths need the lock to be acquired once
and do a whole bunch of stuff and then release it.
This patch creates an unsafe version of the read calls, so
that it can be called from the paths that need the bulk access.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Instead of doing the MAC check, use a flag that gets set per
MAC. This way there are less chances of user error and it
can enable multiple MACs with the capability in a single place
rather than cluttering the code with MAC checks.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
SW needs to acquire the NVM ownership before issuing an AQ read
to the X722 NVM otherwise it will get EBUSY from the firmware.
Also it should be released when done.
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
Fix compilation warnings in base code on some platforms.
Fixes: bd6651c2d2d7 ("i40e/base: use bit shift macros")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Remy Horton <remy.horton@intel.com>
This fixes the issue of not freeing memzone in a call to free the
memory for adminq DMA.
Fixes: 4861cde46116 ("i40e: new poll mode driver")
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Fixes a minor definition change in the Rx descriptor.
Also adds FortPark specific changes to the Descriptors.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Adds support to retrieve and parse WoL/Proxy capabilities from the
device/function list.
Also saves WR_CSR_PROT field from DEV/FUNC capabilities.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Adds admin q function for "Set Wake on LAN Filter AQ"
and "Get Wake Up Reason AQ".
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add AQ functions to handle RSS Key and LUT programming.
This is needed for FortPark RSS support.
FortPark has additional PCTYPES supported for RSS
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds registers and bit field definitions specific to FortPark.
Most of these new registers are related to PE (IWARP), Reset, NVM, RSS
and ATR changes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This is to allow quick check for FCoE capability is enabled or not
in device function before any SW overrides.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The i40e_add_pd_table_entry() routine is being modified to handle both
cases where a backing page is passed and where backing page is allocated
in i40e_add_pd_table_entry().
For pble resource management, it is more efficient for it to manage its
backing pages. For VF, pble backing page addresses will be send to PF
driver for pble resource.
The i40e_remove_pd_bp() is also modified to not free pre-allocated pages and
free only ones which were allocated in i40e_add_pd_table_entry().
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The firmware has added additional status information to allow software
to determine if the APP priority for FCoE/iSCSI/FIP is valid or not in
CEE DCBX mode.
This patch adds to support those additional checks and will only add
applications to the software table that have oper and sync bits set
without any error.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
In order to support some extra Solaris features the Solaris VF drivers need
additional configuration data from the PF that aren't provided with the current
virtual channel commands.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The struct i40e_aqc_get_cee_dcb_cfg_v1_resp was originally defined with
word boundary layout issues, which most compilers deal with by silently
adding padding, making the actual struct larger than designed.
This patch adds an extra byte in fields reserved3 and reserved4 to directly
acknowledge that padding.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The assignments of addr_high and addr_low were not only wrong because
they were assigning virtual addresses to a hardware accessed variable,
but they were shortly thereafter overwritten by the send_asq_command
call with a non-NULL third argument (buffer) with correctly formatted
data.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Use INLINE macro for better cross-platform code management.
Clean up some unnecessary logic jumping and drop a variable.
There was one more __FUNCTION__ reference that wasn't needed.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Add the new Port link status bit and rename the link status to function
link status.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The change is to explicitly assign enum index for each VSI type
so that PF and VF always reference to the same VSI type even if the
enum lists are different.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This will help us avoid a whole bunch of log messages when the driver
is running.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
The Flex10 device/function capability has been upgraded to revision 2
to include information needed to support Flex-10 DCC and DCI
configurations. This patch adds new fields to the i40e_hw_capabilities
structure and updates i40e_parse_discover_capabilities functions to
extract them from the AQ response. Naming convention has changed to use
flex10 mode instead of existing mfp_mode_1.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
This patch adds capability to query and store the CEE DCBX DesiredCfg
and RemoteCfg data from the LLDP MIB.
Added new member "desired_dcbx_config" in the i40e_hw data structure
to hold CEE only DesiredCfg data.
Store the CEE TLV status returned by firmware to allow drivers to dump that
for debug purposes.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
Remove unused members in the PHY structure and add a new member to store
all the capabilities the PHY has as reported by the FW. This information will
help us determine what speeds the device is capable of when link is
down.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Huilong Xu <huilongx.xu@intel.com>
