Equal stride super-buffer Rx datapath will use it as well.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Equal stride super-buffer Rx mode will be handled by the dedicated
Rx datapath and the mode has almost the same Rx event structure as
single packet Rx mode.
Restructure the code to allow the common parts to be shared.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
The function may be shared by different Rx datapath implementations.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Equal stride super-buffer Rx mode is supported by DPDK firmware
variant. One Rx descriptor provides many Rx buffers to firmware.
Rx buffers follow each other with specified stride.
Also it supports head of line blocking with timeout to address
drops when no Rx descriptors are available. So it gives extra time
to the driver to provide Rx descriptors before drop.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The type is an internal interface. Single integer is insufficient
to carry RxQ type-specific information in the case of equal stride
super-buffer Rx mode (packet buffers per bucket, maximum DMA length,
packet stride, head of line block timeout).
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Equal stride super-buffer is a new name instead of deprecated equal
stride packed stream to avoid confusion with previous packed stream.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Drivers should only log with their assigned logtype, not with the
generic PMD log type.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alejandro Lucero <alejandro.lucero@netronome.com>
Be consistent with usage in other drivers.
No need for snowflake drivers.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alejandro Lucero <alejandro.lucero@netronome.com>
The PMD_INIT_LOG macro always adds a newline, and other drivers version
of PMD_DRV_LOG always adds a newline. Therefore change nfp driver
to be consitent with others.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alejandro Lucero <alejandro.lucero@netronome.com>
The NFP driver init messages would come out under PMD not net.pmd.nfp.init.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Alejandro Lucero <alejandro.lucero@netronome.com>
Add rte_flow_action_count action data structure to enable shared
counters across multiple flows on a single port or across multiple
flows on multiple ports within the same switch domain. Also this enables
multiple count actions to be specified in a single flow action.
This patch also modifies the existing rte_flow_query API to take the
rte_flow_action structure as an input parameter instead of the
rte_flow_action_type enumeration to allow querying a specific action
from a flow rule when multiple actions of the same type are specified.
This patch also contains updates for the bonding, failsafe and mlx5 PMDs
and testpmd application which are affected by this API change.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Introduces a new action type RTE_FLOW_ITEM_TYPE_MARK which enables
flow patterns to specify arbitrary integer values to match aginst
set by the RTE_FLOW_ACTION_TYPE_MARK action in previously matched
flows.
Add support for specification of new MARK flow item in testpmd's cli.
Update testpmd documentation to describe new MARK flow item support.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Add jump action type which defines an action which allows a matched
flow to be redirect to the specified group. This allows physical and
logical flow table/group hierarchies to be defined through rte_flow.
This breaks ABI compatibility for the following public functions (as it
modifes the ordering of the rte_flow_action_type enumeration):
- rte_flow_copy()
- rte_flow_create()
- rte_flow_query()
- rte_flow_validate()
Add support for specification of new JUMP action to testpmd's flow
cli, and update the testpmd documentation to describe this new
action.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Add new flow action types and associated action data structures to
support the encapsulation and decapsulation of VXLAN and NVGRE tunnel
endpoints.
The RTE_FLOW_ACTION_TYPE_[VXLAN/NVGRE]_ENCAP action will cause the
matching flow to be encapsulated in the tunnel endpoint overlay
defined in the [vxlan/nvgre]_encap action data.
The RTE_FLOW_ACTION_TYPE_[VXLAN/NVGRE]_DECAP action will cause all
headers associated with the outer most tunnel endpoint of the specified
type for the matching flows.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
RSS action with only one destination queue and no specific settings
for hash types and key does not require dedicated RSS context and
may be simplified to QUEUE action.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Fix internal report on port specific offload capabilities to be 0 (no
capabilities). Before this commit port capabilities were a clone of queue
capabilities, however the current TAP offload capabilities (e.g.
checksum calculation) are per queue and are not specific per port.
This commit fixes an internal validation check for new configured
queue offloads.
The port capability API keeps reporting all queue capabilities as port
capabilities.
Fixes: 95ae196ae1 ("net/tap: use new Rx offloads API")
Fixes: 818fe14a98 ("net/tap: use new Tx offloads API")
Cc: stable@dpdk.org
Signed-off-by: Ophir Munk <ophirmu@mellanox.com>
mask is a simple bit-mask applied before interpreting the contents
of spec and last.
Fixes: a9825ccf5b ("net/sfc: support flow API filters")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Andy Moreton <amoreton@solarflare.com>
Reviewed-by: Roman Zhukov <roman.zhukov@oktetlabs.ru>
Add support for virtual function representor ports to the ixgbe PF
driver. When SR-IOV virtual functions devices are enabled a
corresponding representor port for each VF can be enabled in the
process in which the ixgbe PMD is running within, by specifying the
representor devargs with the list of VF ports that representors
are to be created for.
An example of the devargs which would create VF representor for virtual
functions 0,2,4,5,6 and 7 is:
-w DBDF,representor=[0,2,4-7]
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Mohammad Abdul Awal <mohammad.abdul.awal@intel.com>
Signed-off-by: Remy Horton <remy.horton@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add support for virtual function representor ports to the i40e PF
driver. When SR-IOV virtual functions devices are enabled a
corresponding representor port for each VF can be enabled, in the
process in which the i40e PMD is running, by specifying the
representor devargs with the list of VF ports that representors
are to be created for.
An example of the devargs which would create VF representor for virtual
functions 0,2,4,5,6 and 7 is:
-w DBDF,representor=[0,2,4-7]
and to just specify a single representor on virtual function 3 (switch
port id):
-w DBDF,representor=3
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Signed-off-by: Mohammad Abdul Awal <mohammad.abdul.awal@intel.com>
Signed-off-by: Remy Horton <remy.horton@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add switch domain allocate and free API to enable NET devices to
synchronise switch domain allocation.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Introduces a new structure, rte_eth_devargs, to support generic
ethdev arguments common across NET PMDs, with a new API
rte_eth_devargs_parse API to support PMD parsing these arguments. The
patch add support for a representor argument passed with passed with
the EAL -w option. The representor parameter allows the user to specify
which representor ports to initialise on a device.
The argument supports passing a single representor port, a list of
port values or a range of port values.
-w BDF,representor=1 # create representor port 1 on pci device BDF
-w BDF,representor=[1,2,5,6,10] # create representor ports in list
-w BDF,representor=[0-31] # create representor ports in range
Signed-off-by: Remy Horton <remy.horton@intel.com>
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add the port name to information printed by show port info <port_id>
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add new device flag to specify that an ethdev port is a port
representor. Extend rte_eth_dev_info structure to expose device flags
to the user which enables applications to discover if a port is a
representor port.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add new bus generic ethdev create/destroy APIs which are bus independent
and provide hooks for bus specific initialisation.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Introduces a new port attribute to ethdev port's which denotes the
switch domain a port belongs to. By default all port's switch
identifiers are set to RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID. Ports
which supported the concept of switch domains can be configured with
the same switch domain id.
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Add document to describe the model for representing switching capable
devices in DPDK, using a general ethdev port model and through port
representors. This document also details the port model and the
rte_flow semantics required for flow programming, as well as listing
some example use cases.
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Signed-off-by: Declan Doherty <declan.doherty@intel.com>
Reviewed-by: Marko Kovacevic <marko.kovacevic@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tunnel w/o tunnel id pattern could match any non-tunneled packet,
this patch allowed tunnel w/o tunnel id pattern after proper outer spec.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Dump verb flow detail including flow spec type and size for debugging
purpose.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Tunnel RSS level of flow RSS action offers user a choice to do RSS hash
calculation on inner or outer RSS fields. Testpmd flow command examples:
GRE flow inner RSS:
flow create 0 ingress pattern eth / ipv4 proto is 47 / gre / end
actions rss queues 1 2 end level 1 / end
GRE tunnel flow outer RSS:
flow create 0 ingress pattern eth / ipv4 proto is 47 / gre / end
actions rss queues 1 2 end level 0 / end
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This patch split out flow RSS hash field handling logic to dedicate
function.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Once tunnel packet type(RTE_PTYPE_TUNNEL_xxx) identified,
PKT_RX_IP_CKSUM_XXX and PKT_RX_L4_CKSUM_XXX represent checksum result of
inner headers, outer L3 and L4 header checksum are always valid as soon
as tunnel identified. If no tunnel identified, PKT_RX_IP_CKSUM_XXX and
PKT_RX_L4_CKSUM_XXX represent checksum result of outer L3 and L4
headers.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This patch introduced tunnel type identification based on flow rules.
If flows of multiple tunnel types built on same queue, no tunnel type
will be returned. User application could use bits in flow mark as tunnel
type identifier.
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This patch support L3 VXLAN, no inner L2 header comparing to standard
VXLAN protocol. L3 VXLAN using specific overlay UDP destination port to
discriminate against standard VXLAN, device parameter and FW has to be
configured to support it:
sudo mlxconfig -d <device> -y s IP_OVER_VXLAN_EN=1
sudo mlxconfig -d <device> -y s IP_OVER_VXLAN_PORT=<port>
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
This patch supports new 16 Verbs flow priorities by trying to create a
simple flow of priority 15. If 16 priorities not available, fallback to
traditional 8 priorities.
Verb priority mapping:
8 priorities >=16 priorities
Control flow: 4-7 8-15
User normal flow: 1-3 4-7
User tunnel flow: 0-2 0-3
Signed-off-by: Xueming Li <xuemingl@mellanox.com>
Acked-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
After add RSS hash offload check, default rss_hf will fail on
devices that not support all bits, the patch take rss_hf as
a suggest value and only set bits that device supported base on
rte_eth_dev_get_info, also rss_hf will only be updated when new
rss offload is successfully updated on all ports by
"port config all rss [!default]" command.
Fixes: 8863a1fbfc ("ethdev: add supported hash function check")
Fixes: d9aa619c60 ("app/testpmd: new parameter for port config all RSS command")
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The current code has the following drawbacks:
- It is assumed that TCP 4-tuple hash is
always supported, which is untrue in
the case of packed stream FW variant.
- The driver is unaware of UDP hash support
available with latest firmware.
In order to cope with the mentioned issues, this
patch implements the new approach to handle hash
settings using the advanced EFX RSS interface.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
RSS handling will need more sophisticated fields
in the adapter context storage in future patches.
This patch groups existing fields in a dedicated
structure and updates the rest of the code.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
RSS is one of the most valuable features in the
driver, and one would hardly need to disable it
at build time. This patch withdraws unnecessary
conditionals for RSS snippets.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
One may submit advanced RSS settings as part of
rte_eth_conf to customise RSS configuration from
the very beginning. Currently the driver does not
check that piece of settings and proceeds with
default choices for RSS hash functions and RSS key.
This patch implements the required processing.
Fixes: 4ec1fc3ba8 ("net/sfc: add basic stubs for RSS support on driver attach")
Cc: stable@dpdk.org
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Packed stream firmware variant on EF10 adapters has a
number of properties which must be taken into account:
- Only one exclusive RSS context is available per port.
- Only IP addresses can contribute to the hash value.
Huntington and Medford have one more limitation which
is important for the drivers capable of packed stream:
- Hash algorithm is non-standard (i.e. non-Toeplitz).
This implies XORing together source + destination
IP addresses (or last four bytes in the case of IPv6)
and using the result as the input to a Toeplitz hash.
This patch provides a number of improvements in order
to treat the mentioned limitations in the common code.
If the firmware variant is packed stream, the list of
supported hash tuples will include less variants, and
the maximum number of RSS contexts will be set to one.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Modern firmwares on EF10 adapters have support for
more traffic classes eligible for hash computation.
Also, it has become possible to adjust hashing per
individual class and select distinct packet fields
which will be able to contribute to the hash value.
This patch adds support for the mentioned features.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Currently, libefx has no support for additional RSS modes
available with later controllers. In order to support this,
libefx should be able to list available hash configurations.
This patch provides basic infrastructure for the new interface.
The client drivers will be able to query the list of supported
hash configurations for a particular hash algorithm. Also, it
will be possible to configure hashing by means of new definitions.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
clang 4.0.1-6 on Ubuntu generates false positive warning that shift
is negative. It is done regardless of the fact that the branch is
not taken because of previous check.
The warning is generate in EFX_INSERT_NATIVE32 used by
EFX_INSERT_FIELD_NATIVE32. All similar cases are fixed as well.
It is undesirable to suppress the warning completely.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Add support for the following OpenFlow-defined actions:
- RTE_FLOW_ACTION_OF_POP_VLAN: pop the outer VLAN tag.
- RTE_FLOW_ACTION_OF_PUSH_VLAN: push a new VLAN tag.
- RTE_FLOW_ACTION_OF_SET_VLAN_VID: set the 802.1q VLAN id.
- RTE_FLOW_ACTION_OF_SET_VLAN_PCP: set the 802.1q priority.
- RTE_FLOW_ACTION_OF_POP_MPLS: pop the outer MPLS tag.
- RTE_FLOW_ACTION_OF_PUSH_MPLS: push a new MPLS tag.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Signed-off-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
