Add 'RTE_ETH' namespace to all enums & macros in a backward compatible
way. The macros for backward compatibility can be removed in next LTS.
Also updated some struct names to have 'rte_eth' prefix.
All internal components switched to using new names.
Syntax fixed on lines that this patch touches.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Tyler Retzlaff <roretzla@linux.microsoft.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Wisam Jaddo <wisamm@nvidia.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Chenbo Xia <chenbo.xia@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
There is a confusion on setting max Rx packet length, this patch aims to
clarify it.
'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.
Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.
These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.
Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.
As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.
For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.
When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.
Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Huisong Li <lihuisong@huawei.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Added macros to simplify print of MAC address.
The six bytes of a MAC address are extracted in
a macro here, to improve code readablity.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Currently the sample app user guides use hard coded code snippets,
this patch changes these to use literalinclude which will dynamically
update the snippets as changes are made to the code.
This was introduced in commit 413c75c33c ("doc: show how to include
code in guides"). Comments within the sample apps were updated to
accommodate this as part of this patch. This will help to ensure that
the code within the sample app user guides is up to date and not out
of sync with the actual code.
Signed-off-by: Conor Fogarty <conor.fogarty@intel.com>
Signed-off-by: Conor Walsh <conor.walsh@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
According to the comments and logging, the author just hope user to use
the core and device which are in the same numa node for optimal
performance. If not, A warning gives out.
For example in flow_classify:
./build/flow_classify -a 0000:7d:00.1 -l 93
Here:
0000:7d:00.1 is on numa node 0.
core 93 is on numa node 3.
The two are not in same numa node, but no warning gives out in old codes
when device is on node 0.
This patch includes the node 0 in the check.
Fixes: bab16ddaf2 ("examples/flow_classify: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Tested-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Move pkg-config override to beginning in the Makefile to allow
use PKGCONF variable to detect the libdpdk availability.
Fixes: fda34680eb ("examples: remove legacy sections of makefiles")
Cc: stable@dpdk.org
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
According to the programming guide, the rte_eal_init should be used pairs
with rte_eal_cleanup.
This patch add rte_eal_cleanup to examples to encourage new users of
DPDK to use it.
Fixes: aec9c13c52 ("eal: add function to release internal resources")
Fixes: 3d0fad56b7 ("examples/fips_validation: add crypto FIPS application")
Fixes: c8e6ceeceb ("examples/ioat: add new sample app for ioat driver")
Fixes: 4ff457986f ("examples/l2fwd-event: add default poll mode routines")
Fixes: 08bd1a1744 ("examples/l3fwd-graph: add graph-based l3fwd skeleton")
Fixes: c5eebf85ba ("examples/ntb: add example for NTB")
Fixes: b77f660028 ("examples/pipeline: add new example application")
Fixes: edbed86d1c ("examples/vdpa: introduce a new sample for vDPA")
Fixes: c19beb3f38 ("examples/vhost_blk: introduce vhost storage sample")
Fixes: f5188211c7 ("examples/vhost_crypto: add sample application")
Cc: stable@dpdk.org
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
As with the lib and drivers directories, we can use "continue" keyword to
reduce the indentation level of the majority of the foreach block. At the
same time, we can also replace tab indentation with spaces.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Since the examples are designed to be built by end-users using Make, we
can detect and warn about broken pkg-config on the user's system as part
of the build process.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Replace master lcore with main lcore and
replace slave lcore with worker lcore.
Keep the old functions and macros but mark them as deprecated
for this release.
The "--master-lcore" command line option is also deprecated
and any usage will print a warning and use "--main-lcore"
as replacement.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
The example app makefiles contained sections using the legacy method of
compiling with make. These are no longer needed, and are removed,
leaving only the section that uses pkg-config for the make build.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Nicolas Chautru <nicolas.chautru@intel.com>
Rather than setting -Bstatic in the linker flags when doing a static link,
and then having to explicitly set -Bdynamic again afterwards, we can update
the pkg-config file to use -l:libfoo.a syntax to explicitly refer to the
static library in question. Since this syntax is not supported by meson's
pkg-config module directly, we can post-process the .pc files instead to
adjust them.
Once done, we can simplify the examples' makefiles and the docs by removing
the explicit static flag.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Acked-by: Sunil Pai G <sunil.pai.g@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
The new macro __rte_noreturn, for compiler hinting,
is now used where appropriate for consistency.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some versions of pkg-config don't support the --path flag, which is not a
fatal error when building the apps. Without the flag, the makefile just
cannot track the .pc file of DPDK as a dependency of the build. Therefore,
we can ignore the error and suppress it by redirecting to /dev/null the
stderr from that call to pkg-config.
Fixes: 22119c4591 ("examples: use pkg-config in makefiles")
Cc: stable@dpdk.org
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Not all versions of pkg-config in distros have support for the
--define-prefix flag [1], causing errors when building examples manually or
with test-meson-builds.sh script [2].
For the former case, we need to remove the hard-coded use of the flag in
the Makefiles.
For the latter case, the flag is necessary for builds to succeed, so we
skip the tests when it's not present, passing it as part of the pkg-config
command if it is supported.
[1]
CentOS Linux release 7.7.1908 (Core)
pkg-config version 0.27.1
[2]
## Building cmdline
Unknown option --define-prefix
gmake: Entering directory
`...ild-x86-default/install-root/usr/local/share/dpdk/examples/cmdline'
rm -f build/cmdline build/cmdline-static build/cmdline-shared
test -d build && rmdir -p build || true
Unknown option --define-prefix
Unknown option --define-prefix
gcc -O3 main.c commands.c parse_obj_list.c -o build/cmdline-shared
main.c:14:28: fatal error: cmdline_rdline.h: No such file or directory
Fixes: ca9268529d ("examples: support relocated DPDK install")
Fixes: 7f80a2102b ("devtools: test pkg-config file")
Cc: stable@dpdk.org
Reported-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
The return value of rte_eth_macaddr_get() was changed from void to int.
Update the usage of the functions according to the new return type.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
rte_eth_promiscuous_enable()/rte_eth_promiscuous_disable() return
value was changed from void to int, so this patch modify usage
of these functions across examples according to new return type.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
rte_eth_dev_info_get() return value was changed from void to
int, so this patch modify rte_eth_dev_info_get() usage across
examples/flow_classify according to its new return type.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Make versions before 4.2 did not have support for the .SHELLSTATUS
variable, so use another method to detect shell success.
Fixes: 22119c4591 ("examples: use pkg-config in makefiles")
Cc: stable@dpdk.org
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
For testing of DPDK, we want to override the prefix given by the
pkg-config file, so that we can get correct paths for DPDK installed
in an unusual location.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Since we change these macros, we might as well avoid triggering complaints
from checkpatch because of mixed case.
old=RTE_IPv4
new=RTE_IPV4
git grep -lw $old | xargs sed -i -e "s/\<$old\>/$new/g"
old=RTE_ETHER_TYPE_IPv4
new=RTE_ETHER_TYPE_IPV4
git grep -lw $old | xargs sed -i -e "s/\<$old\>/$new/g"
old=RTE_ETHER_TYPE_IPv6
new=RTE_ETHER_TYPE_IPV6
git grep -lw $old | xargs sed -i -e "s/\<$old\>/$new/g"
Signed-off-by: David Marchand <david.marchand@redhat.com>
Reviewed-by: Olivier Matz <olivier.matz@6wind.com>
Add 'RTE_' prefix to defines:
- rename ETHER_ADDR_LEN as RTE_ETHER_ADDR_LEN.
- rename ETHER_TYPE_LEN as RTE_ETHER_TYPE_LEN.
- rename ETHER_CRC_LEN as RTE_ETHER_CRC_LEN.
- rename ETHER_HDR_LEN as RTE_ETHER_HDR_LEN.
- rename ETHER_MIN_LEN as RTE_ETHER_MIN_LEN.
- rename ETHER_MAX_LEN as RTE_ETHER_MAX_LEN.
- rename ETHER_MTU as RTE_ETHER_MTU.
- rename ETHER_MAX_VLAN_FRAME_LEN as RTE_ETHER_MAX_VLAN_FRAME_LEN.
- rename ETHER_MAX_VLAN_ID as RTE_ETHER_MAX_VLAN_ID.
- rename ETHER_MAX_JUMBO_FRAME_LEN as RTE_ETHER_MAX_JUMBO_FRAME_LEN.
- rename ETHER_MIN_MTU as RTE_ETHER_MIN_MTU.
- rename ETHER_LOCAL_ADMIN_ADDR as RTE_ETHER_LOCAL_ADMIN_ADDR.
- rename ETHER_GROUP_ADDR as RTE_ETHER_GROUP_ADDR.
- rename ETHER_TYPE_IPv4 as RTE_ETHER_TYPE_IPv4.
- rename ETHER_TYPE_IPv6 as RTE_ETHER_TYPE_IPv6.
- rename ETHER_TYPE_ARP as RTE_ETHER_TYPE_ARP.
- rename ETHER_TYPE_VLAN as RTE_ETHER_TYPE_VLAN.
- rename ETHER_TYPE_RARP as RTE_ETHER_TYPE_RARP.
- rename ETHER_TYPE_QINQ as RTE_ETHER_TYPE_QINQ.
- rename ETHER_TYPE_ETAG as RTE_ETHER_TYPE_ETAG.
- rename ETHER_TYPE_1588 as RTE_ETHER_TYPE_1588.
- rename ETHER_TYPE_SLOW as RTE_ETHER_TYPE_SLOW.
- rename ETHER_TYPE_TEB as RTE_ETHER_TYPE_TEB.
- rename ETHER_TYPE_LLDP as RTE_ETHER_TYPE_LLDP.
- rename ETHER_TYPE_MPLS as RTE_ETHER_TYPE_MPLS.
- rename ETHER_TYPE_MPLSM as RTE_ETHER_TYPE_MPLSM.
- rename ETHER_VXLAN_HLEN as RTE_ETHER_VXLAN_HLEN.
- rename ETHER_ADDR_FMT_SIZE as RTE_ETHER_ADDR_FMT_SIZE.
- rename VXLAN_GPE_TYPE_IPV4 as RTE_VXLAN_GPE_TYPE_IPV4.
- rename VXLAN_GPE_TYPE_IPV6 as RTE_VXLAN_GPE_TYPE_IPV6.
- rename VXLAN_GPE_TYPE_ETH as RTE_VXLAN_GPE_TYPE_ETH.
- rename VXLAN_GPE_TYPE_NSH as RTE_VXLAN_GPE_TYPE_NSH.
- rename VXLAN_GPE_TYPE_MPLS as RTE_VXLAN_GPE_TYPE_MPLS.
- rename VXLAN_GPE_TYPE_GBP as RTE_VXLAN_GPE_TYPE_GBP.
- rename VXLAN_GPE_TYPE_VBNG as RTE_VXLAN_GPE_TYPE_VBNG.
- rename ETHER_VXLAN_GPE_HLEN as RTE_ETHER_VXLAN_GPE_HLEN.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add 'rte_' prefix to structures:
- rename struct ether_addr as struct rte_ether_addr.
- rename struct ether_hdr as struct rte_ether_hdr.
- rename struct vlan_hdr as struct rte_vlan_hdr.
- rename struct vxlan_hdr as struct rte_vxlan_hdr.
- rename struct vxlan_gpe_hdr as struct rte_vxlan_gpe_hdr.
Do not update the command line library to avoid adding a dependency to
librte_net.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The "make clean" command had a number of issues:
- the "--ignore-fail-on-non-empty" flag is not present on BSD
- the call to remove the build folder would fail if there was no build
folder present.
These are fixed by only removing the build folder if it exists, and by
using -p flag to rmdir in place of --ignore-fail-on-non-empty
Fixes: 22119c4591 ("examples: use pkg-config in makefiles")
Cc: stable@dpdk.org
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Most examples have in their makefiles a default RTE_TARGET directory to be
used in case RTE_TARGET is not set. Rather than just using a hard-coded
default, we can instead detect what the build directory is relative to
RTE_SDK directory.
This fixes a potential issue for anyone who continues to build using
"make install T=x86_64-native-linuxapp-gcc" and skips setting RTE_TARGET
explicitly, instead relying on the fact that they were building in a
directory which corresponded to the example default path - which was
changed to "x86_64-native-linux-gcc" by commit 218c4e68c1 ("mk: use
linux and freebsd in config names").
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Rather than using linuxapp and bsdapp everywhere, we can change things to
use the, more readable, terms "linux" and "freebsd" in our build configs.
Rather than renaming the configs we can just duplicate the existing ones
with the new names using symlinks, and use the new names exclusively
internally. ["make showconfigs" also only shows the new names to keep the
list short] The result is that backward compatibility is kept fully but any
new builds or development can be done using the newer names, i.e. both
"make config T=x86_64-native-linuxapp-gcc" and "T=x86_64-native-linux-gcc"
work.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
In DPDK 17.11, the ethdev offloads API has changed:
commit cba7f53b71 ("ethdev: introduce Tx queue offloads API")
commit ce17eddefc ("ethdev: introduce Rx queue offloads API")
The new API is documented in the programmer's guide:
http://doc.dpdk.org/guides/prog_guide/poll_mode_drv.html#hardware-offload
For reminder, the main concepts in the new API were:
- All offloads are disabled by default
- Distinction between per port and per queue offloads.
The transition bits are now removed:
- Translation of the old API in ethdev
- rte_eth_conf.rxmode.ignore_offload_bitfield
- ETH_TXQ_FLAGS_IGNORE
The old API bits are now removed:
- Rx per-port rte_eth_conf.rxmode.[bit-fields]
- Tx per-queue rte_eth_txconf.txq_flags
- ETH_TXQ_FLAGS_NO*
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Andrew Rybchenko <arybchenko@solarflare.com>
Reviewed-by: Shahaf Shuler <shahafs@mellanox.com>
The port_init function calls the rte_eth_dev_is_valid_port function.
This function now returns 1 if the port state is attached.
A return value of 1 now means a valid port.
Fixes: a9dbe18022 ("fix ethdev port id validation")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
In order to fix this common mistake in all external applications,
the function rte_eth_dev_count is deprecated, while introducing
the new functions rte_eth_dev_count_avail and rte_eth_dev_count_total.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application assume a valid port index is in the range [0..count[.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be valid
- old ports being detached (RTE_ETH_DEV_UNUSED) can be valid
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the function rte_eth_dev_is_valid_port.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Some DPDK applications wrongly assume these requirements:
- no hotplug, i.e. ports are never detached
- all allocated ports are available to the application
Such application iterates over ports by its own mean.
The most common pattern is to request the port count and
assume ports with index in the range [0..count[ can be used.
There are three consequences when using such wrong design:
- new ports having an index higher than the port count won't be seen
- old ports being detached (RTE_ETH_DEV_UNUSED) can be seen as ghosts
- failsafe sub-devices (RTE_ETH_DEV_DEFERRED) will be seen by the application
Such mistake will be less common with growing hotplug awareness.
All applications and examples inside this repository - except testpmd -
must be fixed to use the iterator RTE_ETH_FOREACH_DEV.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Increase the default RX/TX ring sizes to 1024/1024 to
accommodate for NICs with higher throughput (25G, 40G etc)
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Since the DPDK build now includes both static and shared libraries, we need
a new way to enable building the examples using either method from the one
installation. To do this, we add in a default "shared" target, and a
separate "static" target which links in the DPDK static libraries. In both
cases, the final application name is symlinked to the last-built static or
shared target, with both binaries able to co-exist in the build directory.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Change the example app Makefiles to query if DPDK is installed and
registered using pkg-config. If so, build directly using pkg-config info,
otherwise fall back to using the original build system with RTE_SDK and
RTE_TARGET
This commit changes the makefiles for the basic examples, i.e. those which
do not have multiple subdirectories underneath the main examples dir.
Examples not covered are:
* ethtool
* multi_process
* performance-thread
* quota_watermark
* netmap_compat
* server_node_efd
* vm_power_manager
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Luca Boccassi <bluca@debian.org>
Reorder the text in the makefiles, so that the app name and the source
files are listed first. This then will allow them to be shared later in a
combined makefile building with pkg-config and RTE_SDK-based build system.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Luca Boccassi <bluca@debian.org>
Add support for having selected example apps built as part of a meson,
ninja build. By default none are built, and those to be built should be
named directly in the -Dexamples='' meson configuration argument.
This is useful for developers working on a feature who want to use a
suitable example, or examples, to test that feature, as they can compile
everything up in one go, and run the example without having to do a ninja
install first.
This commit adds examples which don't consist of multiple apps in
subdirectories to the meson build, so they can be built by default by
passing -Dexamples parameter to meson.
Not included are the following examples:
* ethtool
* multi-process
* netmap_compat
* performance-thread
* quota_watermark
* server_node_efd
* vm_power_manager
To test the apps added here, use the following command, merged to one line,
to add them to your meson build (command to be run inside the build
directory):
meson configure -Dexamples=bbdev_app,bond,cmdline,distributor,\
eventdev_pipeline_sw_pmd, exception_path,helloworld,\
ip_fragmentation,ip_pipeline,ip_reassembly, ipsec-secgw,\
ipv4_multicast,kni,l2fwd-cat,l2fwd-crypto,l2fwd-jobstats,\
l2fwd-keepalive,l2fwd,l3fwd-acl,l3fwd-power,l3fwd-vf,l3fwd,\
link_status_interrupt,load_balancer,packet_ordering,ptpclient,\
qos_meter,qos_sched,rxtx_callbacks,skeleton,tep_termination,\
timer,vhost,vhost_scsi,vmdq,vmdq_dcb
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Luca Boccassi <bluca@debian.org>
Add checks during build to ensure that all symbols in the EXPERIMENTAL
version map section have __experimental tags on their definitions, and
enable the warnings needed to announce their use. Also add an
ALLOW_EXPERIMENTAL_APIS define to allow individual libraries and files
to declare the acceptability of experimental api usage
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
This patch removes table id parameter from all the flow
classify apis to reduce the complexity alongwith some code
cleanup.
The validate api is exposed as public api to allow user
to validate the flow before adding it to the classifier.
Signed-off-by: Jasvinder Singh <jasvinder.singh@intel.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
Replace the BSD license header with the SPDX tag for files
with only an Intel copyright on them.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Check return value of fseek and exit if non zero.
Coverity issue: 143435
Fixes: bab16ddaf2 ("examples/flow_classify: add sample application")
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Jasvinder Singh <jasvinder.singh@intel.com>
The flow_classify sample application exercises the following
librte_flow_classify API's:
rte_flow_classifier_create
rte_flow_classifier_query
rte_flow_classify_table_create
rte_flow_classify_table_entry_add
rte_flow_classify_table_entry_delete
It sets up the IPv4 ACL field definitions.
It creates table_acl and adds and deletes rules using the
librte_table API.
It uses a file of IPv4 five tuple rules for input.
Signed-off-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Jasvinder Singh <jasvinder.singh@intel.com>
