The wrong queue id was being used in the enic
flow director code after the scattered Rx feature
was added.
Fixes: 856d7ba7ed22 ("net/enic: support scattered Rx")
Signed-off-by: John Daley <johndale@cisco.com>
Update the enic guide to better explain how to setup vNIC parameters
on the Cisco VIC since the introduction of rx scatter, and print an
error message for the case of having 1 RQ configured in the vNIC,
referring to the documentation for more information.
Signed-off-by: Nelson Escobar <neescoba@cisco.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Summary:
- add secondary qset support in device stats
- add support for releasing mbufs from RBDR for >8 queues
- add support for releasing mbufs from RX queues for >8 queues
- support >8 queues in tx_queue_setup
- support >8 queues in rx_queue_setup
- support up to 96 queues per device (dev_info->max_rx_queues)
- add secondary qset support in rbdr_rte_mempool_get
- support >8 queues in multiprocess mode (do not reconfigure VFs)
- setup periodic alarm accordingly for type of VFs:
* primary VF - handle events on queues and link status
* secondary VF - handle events on queues
- initialize hardware capabilities in secondary qsets
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
In case of the multiprocess mode a shared nicvf struct between processes
cannot point with the eth_dev pointer to master device, therefore remove it
along with references to it refactoring the code where needed.
This change fixes multiprocess issues detected in stats.
Fixes: 7413feee662d ("net/thunderx: add device start/stop and close")
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Changes:
- add new message sqs_alloc in mailbox
- add a queue container to hold secondary qsets.
- add nicvf_mbox_request_sqs
- handle new mailbox messages for secondary queue set support
- register secondary queue sets for further reuse
- register the number secondary queue sets in MSG_QS_CFG
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
This interface (nicvf_bsvf) will be used for secondary queue set support.
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
The symbols PKT_TX_TCP_CKSUM and PKT_TX_UDP_CKSUM are not bits on a
bitmask. Set l3_offset always for TX offloads, not just for PKT_TX_IP_CKSUM
being true.
Fixes: 1c421f18e095 ("net/thunderx: add single and multi-segment Tx")
Signed-off-by: Maciej Czekaj <maciej.czekaj@caviumnetworks.com>
Signed-off-by: Kamil Rytarowski <kamil.rytarowski@caviumnetworks.com>
Signed-off-by: Zyta Szpak <zyta.szpak@semihalf.com>
Signed-off-by: Slawomir Rosek <slawomir.rosek@semihalf.com>
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Decode the checksum flags from the Rx descriptor, setting
the appropriate bit in the mbuf ol_flags field when the flag
indicates a bad checksum.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Signed-off-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
The ptype is decoded from the Rx descriptor and stored
in the packet type field in the mbuf using the same function
in the non-vector driver.
Signed-off-by: Damjan Marion <damarion@cisco.com>
Signed-off-by: Jeff Shaw <jeffrey.b.shaw@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Jing Chen <jing.d.chen@intel.com>
SR-IOV virtual functions cannot rely on promiscuous mode for the reception
of VLAN tagged frames. Program the VLAN filter for each slave when a
VLAN is configured for the bonding master.
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
It's possible for the bonding driver to mistakenly reject an interface
based in it's, as yet, unnegotiated link speed and duplex. Always allow
the interface to be added to the bonding interface but require link
properties validation to succeed before slave is activated.
Fixes: 2efb58cbab6e ("bond: new link bonding library")
Signed-off-by: Eric Kinzie <ehkinzie@gmail.com>
Acked-by: Bernard Iremonger <bernard.iremonger@intel.com>
This patch adds "Limitations or Known issues" section for
i40e PMD, including two items:
1. MPLS packet classification on X710/XL710
2. 16 Byte Descriptor cannot be used on DPDK VF
3. Link down with i40e kernel driver after DPDK application exist
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Since switched to kernel dynamic debugging it is possible to remove
compile time debug log configuration.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Switch to dynamic logging functions. Depending kernel configuration this
may cause previously visible logs disappear.
How to enable dynamic logging:
https://www.kernel.org/doc/Documentation/dynamic-debug-howto.txt
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Allow binding KNI thread to specific core in single threaded mode
by setting core_id and force_bind config parameters.
Signed-off-by: Vladyslav Buslov <vladyslav.buslov@harmonicinc.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tested-by: Ferruh Yigit <ferruh.yigit@intel.com>
As a bug-fix for lpm tbl8 recycle is introduced,
add a test case to verify tbl8 group is correctly
freed when it only includes a rule with depth=24.
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
When a rule with depth > 24 is added into an existing
rule with depth <=24, a new tbl8 is allocated, the existing
rule first fulfill whole new tbl8, so the filed valid of
each entry in this tbl8 is always true and depth of each
entry is always <= 24 before adding the new rule with depth > 24.
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
When all rules with depth > 24 are deleted in a same sub-table
(tlb8 group) and only a rule with depth <=24 is left in it,
this sub-table (tlb8 group) should be recycled.
Fixes: dc81ebbacaeb ("lpm: extend IPv4 next hop field")
Fixes: af75078fece3 ("first public release")
Signed-off-by: Wei Dai <wei.dai@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Before this patch, application-specific loggers could not be
installed before rte_eal_init completed (the initialization process
called rte_openlog_stream, overwriting any previously installed
logger). This made it impossible for an application to capture the
initial log messages generated during rte_eal_init. This patch changes
initialization so that information from a previous call to
rte_openlog_stream is not lost. Specifically:
* The default log stream is now maintained separately from an
application-specific log stream installed with rte_openlog_stream.
* rte_eal_common_log_init has been renamed to eal_log_set_default,
since this is all it does. It no longer invokes rte_openlog_stream; it
just updates the default stream. Also, this method now returns void,
rather than int, since there are no errors.
This patch also removes the "early log" mechanism and cleans up the
log initialization mechanism:
* The default log stream defaults to stderr on all platforms if
eal_log_set_default hasn't been invoked (Linux used to use stdout
during the first part of initialization).
* Removed rte_eal_log_early_init; all of the desired functionality can
be achieved by calling eal_log_set_default.
* Removed lib/librte_eal/bsdapp/eal/eal_log.c: it contained only one
function, rte_eal_log_init, which is not needed or invoked for BSD.
* Removed declaration for eal_default_log_stream in rte_log.h (it's now
private to eal_common_log.c).
* Moved call to rte_eal_log_init earlier in rte_eal_init for Linux, so
that it starts using the preferrred log ASAP.
Signed-off-by: John Ousterhout <ouster@cs.stanford.edu>
Previous patch updated the functions without updating all the comments.
Fixes: 591a9d7985c1 ("add FILE argument to debug functions")
Signed-off-by: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: John McNamara <john.mcnamara@intel.com>
