Indirect actions should be used to do shared counters.
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Ori Kam <orika@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Make it simpler to debug configurations and code related to the representor
info API.
Signed-off-by: Viacheslav Galaktionov <viacheslav.galaktionov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Andy Moreton <amoreton@xilinx.com>
Reviewed-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
When configuring DCB, testpmd retains the rx_mode/tx_mode configuration in
rte_port->dev_conf. But some configurations, such as the link_speed, were
not saved if they were set before configuring DCB.
Fixes: 1a572499be ("app/testpmd: setup DCB forwarding based on traffic class")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Add a new cmdline to help diagnostic the bonding mode 4 in testpmd.
Show the lacp information about the bonded device and its slaves:
show bonding lacp info <bonded device port_id>
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
When random number of Tx segments is enabled, because the actual
number of segments may be only one, the first segment of the Tx
packets must accommodate a complete being sending Eth/IP/UDP packet.
Besides, if multiple flow is enabled, the forwarding will update
the IP and UDP header, these headers shouldn't cross segments.
This also requires the first Tx segment can accommodate a complete
Eth/IP/UDP packet.
In addition, if time stamp is enabled, the forwarding needs more
Tx segment space for time stamp information.
This patch adds checks in beginning of forward engine to make sure
all above conditions are met.
Bugzilla ID: 797
Fixes: 79bec05b32 ("app/testpmd: add ability to split outgoing packets")
Cc: stable@dpdk.org
Signed-off-by: Alvin Zhang <alvinx.zhang@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
For each forward engine, there may be some special conditions
must be met before the forwarding runs.
Adding checks for these conditions in configuring is not suitable,
because one condition may rely on multiple configurations, and the
conditions required by each forward engine is not general.
The best solution is each forward engine has a callback to check
whether these conditions are met, and then testpmd can call the
callback to determine whether the forwarding can be started.
There was a void callback 'port_fwd_begin' in forward engine,
it did some initialization for forwarding, this patch updates its
return value then we can add some checks in it to confirm whether
the forwarding can be started. In addition, this patch calls the
callback before the forwarding stats is reset and then launches the
forwarding engine.
Bugzilla ID: 797
Cc: stable@dpdk.org
Signed-off-by: Alvin Zhang <alvinx.zhang@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Fix the mempool flags namespace by adding an RTE_ prefix to the name.
The old flags remain usable, to be deprecated in the future.
Flag MEMPOOL_F_NON_IO added in the release is just renamed to have RTE_
prefix.
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
A more fine-grain flow API action RTE_FLOW_ACTION_TYPE_SAMPLE should
be used instead of it.
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Definition of `rte_ether_addr` structure used a workaround allowing DPDK
and Windows SDK headers to be used in the same file, because Windows SDK
defines `s_addr` as a macro. Rename `s_addr` to `src_addr` and `d_addr`
to `dst_addr` to avoid the conflict and remove the workaround.
Deprecation notice:
https://mails.dpdk.org/archives/dev/2021-July/215270.html
Signed-off-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
This updates the gtp_psc flow item to use the net header
definition of the gtp_psc to be based on RFC 38415-g30
Signed-off-by: Raslan Darawsheh <rasland@nvidia.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch defines new RSS offload types for IPv4 and
L4(TCP/UDP/SCTP) checksum, which are required when users want
to distribute packets based on the IPv4 or L4 checksum field.
For example "flow create 0 ingress pattern eth / ipv4 / end
actions rss types ipv4-chksum end queues end / end", this flow
causes all matching packets to be distributed to queues on
basis of IPv4 checksum.
Signed-off-by: Alvin Zhang <alvinx.zhang@intel.com>
Reviewed-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Aman Deep Singh <aman.deep.singh@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added macros to simplify print of MAC address.
The six bytes of a MAC address are extracted in
a macro here, to improve code readablity.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Added macro to print six bytes of MAC address.
The MAC addresses will be printed in upper case
hexadecimal format.
In case there is a specific check for lower case
MAC address, the user may need to make a change in
such test case after this patch.
Signed-off-by: Aman Deep Singh <aman.deep.singh@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
This patch adds multi-process support for testpmd.
For example the following commands run two testpmd
processes:
* the primary process:
./dpdk-testpmd --proc-type=auto -l 0-1 -- -i \
--rxq=4 --txq=4 --num-procs=2 --proc-id=0
* the secondary process:
./dpdk-testpmd --proc-type=auto -l 2-3 -- -i \
--rxq=4 --txq=4 --num-procs=2 --proc-id=1
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Aman Deep Singh <aman.deep.singh@intel.com>
Make number of flows in flowgen configurable by setting parameter
--flowgen-flows=N.
Signed-off-by: Zhihong Wang <wangzhihong.wzh@bytedance.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Donot use outer metadata when neither outer ip checksum nor
outer udp checksum is enabled. PMD's will ignore the
outer_l2_len and outer_l3_len in cases where none of
the outer checksum is enabled and hence only l2_len and
l3_len will be used to calculate the offsets for L2 or L3
header.
Fixes: 3c32113a1a ("app/testpmd: fix IPv6 tunnel checksum")
Cc: stable@dpdk.org
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Use per-core variable for flow indexing to solve cache contention in
multi-core scenarios.
Signed-off-by: Zhihong Wang <wangzhihong.wzh@bytedance.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Call inc_rx_burst_stats for rx operation, and record fwd_dropped.
Signed-off-by: Zhihong Wang <wangzhihong.wzh@bytedance.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Use the rte_ipv4_cksum API to replace local ip_sum implementation.
Signed-off-by: Zhihong Wang <wangzhihong.wzh@bytedance.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
UDP protocol reserves 0 checksum value for special purposes.
Other protocols, like IPv4, TCP and SCTP must calculate checksum value
in software or offload checksum calculation to hardware.
If IPv4 TX checksum offload was off and header checksum was set to 0,
testpmd csum engine did not calculate checksum value for IPv4, TCP and
SCTP.
The patch always calculates IPv4, TCP and SCTP TX checksums if it is
not offloaded.
Bugzilla ID: 768
Fixes: b2a9e4a855 ("app/testpmd: fix Tx checksum calculation for tunnel")
Cc: stable@dpdk.org
Signed-off-by: Gregory Etelson <getelson@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
After removing rte_eth_devices from testpmd the vm_hotplug no longer
recovered after removal of a device, because the port was closed
before querying it.
Fixes: 0a0821bcf3 ("app/testpmd: remove most uses of internal ethdev array")
Signed-off-by: Paulis Gributs <paulis.gributs@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
csumonly engine calculates Tx checksum of a tunnelled packet
for outer headers only or separately for outer and inner headers.
The calculation method is determined by checksum configuration options.
If Tx checksum calculation is separated,
the inner headers are processed before outer headers.
Inner headers processing sets checksum values to 0 unconditionally.
If Tx configuration offloads inner checksums only, outer checksum
calculation in software will read 0 instead of real values
and produce wrong result.
The patch zeroes inner checksums only before software calculation.
Fixes: 6b520d54eb ("app/testpmd: use Tx preparation in checksum engine")
Cc: stable@dpdk.org
Signed-off-by: Gregory Etelson <getelson@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Olivier Matz <olivier.matz@6wind.com>
Running with stdout suppressed or redirected for further processing
is very confusing in the case of errors. Fix it by logging errors and
warnings to stderr.
Since lines with log messages are touched anyway concatenate split
format strings to make it easier to search using grep.
Fix indent of format string arguments.
Signed-off-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
This patch removes most uses of the global variable rte_eth_devices
from testpmd. This was done to avoid using the object directly which
applications should not do.
Most uses have been replaced with standard function calls, however
the use of it in the show_macs function could not be replaced as no
function call exists to get all mac addresses of a given port.
Signed-off-by: Paulis Gributs <paulis.gributs@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
MAC address of each port in global variable ports hasn't been updated
after resetting. It was the initial one after resetting VF MAC address.
This patch gets correct port MAC address when starting port.
Fixes: a5279d2561 ("app/testpmd: check status of getting MAC address")
Cc: stable@dpdk.org
Signed-off-by: Yuying Zhang <yuying.zhang@intel.com>
Acked-by: Aman Deep Singh <aman.deep.singh@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Command help string is missing 'reset' keyword,
although description has it. Adding it.
Fixes: 97f1e19679 ("app/testpmd: add port reset command")
Cc: stable@dpdk.org
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Add a new testpmd pattern field 'last_rsvd' that supports the
last 8-bits matching of VXLAN header.
The examples for the "last_rsvd" pattern field are as below:
1. ...pattern eth / ipv4 / udp / vxlan last_rsvd is 0x80 / end ...
This flow will exactly match the last 8-bits to be 0x80.
2. ...pattern eth / ipv4 / udp / vxlan last_rsvd spec 0x80
vxlan mask 0x80 / end ...
This flow will only match the MSB of the last 8-bits to be 1.
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Acked-by: Raslan Darawsheh <rasland@nvidia.com>
The new flow item allows PMD to offload IPv4 IHL field for matching,
if hardware supports that operation.
Signed-off-by: Gregory Etelson <getelson@nvidia.com>
Reviewed-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
For the newly attached ports (with "port attach" command) the
default offloads settings, configured from application command
line, were not applied, causing port start failure following
the attach.
For example, if scattering offload was configured in command
line and rxpkts was configured for multiple segments, the newly
attached port start was failed due to missing scattering offload
enable in the new port settings. The missing code to apply
the offloads to the new device and its queues is added.
The new local routine init_config_port_offloads() is introduced,
embracing the shared part of port offloads initialization code.
Fixes: c9cce42876 ("ethdev: remove deprecated attach/detach functions")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Acked-by: Aman Deep Singh <aman.deep.singh@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
When we use the following cmd to modify the link speed of specified
port: "port config <port_id> speed xxx duplex xxx", we have to stop
all ports. It's not necessary.
Fixes: 82113036e4 ("ethdev: redesign link speed config")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Function print_fdir_mask and print_fdir_flex_payload are only called
when either i40e or ixgbe presents. Extend existing #if defined to
include these two functions, to remove "unused function" compilation
warning.
Signed-off-by: Jie Zhou <jizh@linux.microsoft.com>
Acked-by: Tal Shnaiderman <talshn@nvidia.com>
Acked-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
- Make printf format OS independent
- Replace htons with RTE_BE16
- Replace POSIX specific inet_aton with OS independent inet_pton
- Replace sleep with rte_delay_us_sleep
- Replace random with rte_rand
- #ifndef mman related code for now
- Fix header inclusion
- Include rte_os_shim.h in testpmd.h
- Remove redundant headers
Signed-off-by: Jie Zhou <jizh@linux.microsoft.com>
Acked-by: Tal Shnaiderman <talshn@nvidia.com>
Acked-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
Passing an uint32_t pointer to an enum pointer parameter causes
pointer-sign warning on Windows (converts between pointers to
integer types with different sign), since enum is implicitly
converted to int on Windows.
And the current enum pointer parameter of that function is actually
misleading and should be fixed as an uint32_t pointer parameter.
Fixes: b19da32e31 ("app/testpmd: add FEC command")
Cc: stable@dpdk.org
Signed-off-by: Jie Zhou <jizh@linux.microsoft.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Resolve name collisions with Windows types.
Signed-off-by: Jie Zhou <jizh@linux.microsoft.com>
Acked-by: Tal Shnaiderman <talshn@nvidia.com>
Acked-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
Use out only after it was checked not to be null.
Fixes: 4d07cbefe3 ("app/testpmd: add commands for conntrack")
Cc: stable@dpdk.org
Signed-off-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Reviewed-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Aman Deep Singh <aman.deep.singh@intel.com>
Currently action RTE_FLOW_ACTION_TYPE_METER_COLOR is defined.
Add the CLI for this action: color type (types)
There are three types: green, yellow and red.
Example for the new policy meter CLIs:
add port meter policy 0 1 g_actions color type green / end y_actions
color type yellow / end r_actions color type red / end
In the above command, the action type is
RTE_FLOW_ACTION_TYPE_METER_COLOR, the meter policy action list:
green -> green, yellow -> yellow, red -> red.
Signed-off-by: Haifei Luo <haifeil@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
Acked-by: Cristian Dumitrescu <cristian.dumitrescu@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Tunnel offload model requires application to obtain PMD related flow
items or actions to construct a flow rule. These elements acquire
internal PMD flow resources that must be explicitly released.
The patch destroys tunnel offload PMD resources after flow creation
failure.
Fixes: 1b9f274623 ("app/testpmd: add commands for tunnel offload")
Cc: stable@dpdk.org
Signed-off-by: Gregory Etelson <getelson@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Counter action query was implemented as part of flow query, but was not
implemented as part of indirect action query.
This patch adds the required implementation.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
The port_action_handle_query function supports query operation for
indirect RSS action.
No driver currently supports this operation, and this support is
unnecessary.
Remove it.
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
The fwd_config_setup() is called after init_fwd_streams().
The fwd_config_setup() will reinitialize forwarding streams.
This patch removes init_fwd_streams() from init_config().
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
This patch adds fwd_config_setup() at the end of cmd_config_dcb_parsed()
to update "cur_fwd_config", so that the actual forwarding streams can be
queried by the "show config fwd" cmd.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Currently, the check for doing DCB test is assigned to
start_packet_forwarding(), which will be called when
run "start" cmd. But fwd_config_setup() is used in many
scenarios, such as, "port config all rxq".
This patch moves the check from start_packet_forwarding()
to fwd_config_setup().
Fixes: 7741e4cf16 ("app/testpmd: VMDq and DCB updates")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Currently, '.get_dcb_info' must be supported for the port doing DCB
test, or all information in 'rte_eth_dcb_info' are zero. It should be
prevented when user run cmd "port config 0 dcb vt off 4 pfc off".
This patch adds the check for support of reporting dcb info.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
After DCB mode is configured, if we decrease the number of RX and TX
queues, fwd_config_setup() will be called to setup the DCB forwarding
configuration. And forwarding streams are updated based on new queue
numbers in fwd_config_setup(), but the mapping between the TC and
queues obtained by rte_eth_dev_get_dcb_info() is still old queue
numbers (old queue numbers are greater than new queue numbers).
In this case, the segment fault happens. So rte_eth_dev_configure()
should be called again to update the mapping between the TC and
queues before rte_eth_dev_get_dcb_info().
Like:
set nbcore 4
port stop all
port config 0 dcb vt off 4 pfc on
port start all
port stop all
port config all rxq 8
port config all txq 8
Fixes: 900550de04 ("app/testpmd: add dcb support")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
After DCB mode is configured, the operations of port stop and port start
change the value of the global variable "dcb_test", As a result, the
forwarding configuration from DCB to RSS mode, namely,
“dcb_fwd_config_setup()” to "rss_fwd_config_setup()".
Currently, the 'dcb_flag' field in struct 'rte_port' indicates whether
the port is configured with DCB. And it is sufficient to have
'dcb_config' as a global variable to control the DCB test status. So
this patch deletes the "dcb_test".
In addition, setting 'dcb_config' at the end of init_port_dcb_config()
in case that ports fail to enter DCB mode.
Fixes: 900550de04 ("app/testpmd: add dcb support")
Fixes: ce8d561418 ("app/testpmd: add port configuration settings")
Fixes: 7741e4cf16 ("app/testpmd: VMDq and DCB updates")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
For the DCB forwarding test, each core is assigned to each traffic class.
Number of forwarding cores for DCB test must be equal or less than number
of total TC. Otherwise, the following problems may occur:
1/ Redundant polling threads will be created when forwarding cores number
is greater than total TC number.
2/ Two cores would try to use a same queue on a port when Rx/Tx queue
number is greater than the used TC number, which is not allowed.
Fixes: 900550de04 ("app/testpmd: add dcb support")
Fixes: ce8d561418 ("app/testpmd: add port configuration settings")
Cc: stable@dpdk.org
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Variable total, which may be zero and result in segmentation fault.
This patch fixed it.
Fixes: 9b1249d9ff ("app/testpmd: support dumping socket memory")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The --txpkts command line parameter was silently ignored due to
application was unable to check the Tx queue ring sizes for non
configured ports.
The "set txpkts <len0[,len1]*>" was also rejected if there
was some stopped or /unconfigured port.
This provides the following:
- If fails to get ring size from the port, this can be because port is
not initialized yet, ignore the check and just be sure segment size
won't cause an out of bound access. The port descriptor check will
be done during Tx setup.
- The capability to send single packet is supposed to be very basic
and always supported, the setting segment number to 1 is always
allowed, no check performed
- At the moment of Tx queue setup the descriptor number is checked
against configured segment number
Bugzilla ID: 584
Fixes: 8dae835d88 ("app/testpmd: remove restriction on Tx segments set")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
