Add support for dequeue, dequeue_burst, ...
DLB2 does not currently support interrupts, but instead use
umonitor/umwait if supported by the processor. This allows
the software to monitor and wait on writes to a cache-line.
DLB2 supports normal and sparse cq mode. In normal mode the
hardware will pack 4 QEs into each cache line. In sparse cq
mode, the hardware will only populate one QE per cache line.
Software must be aware of the cq mode, and take the appropriate
actions, based on the mode.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Configure the load balanced (ldb) or directed (dir) port.
The consumer queue (CQ) and producer port (PP) are also
set up here.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Load balanced (ldb) queues are setup here.
Directed queues are not set up until link time, at which
point we know the directed port ID. Directed queue setup
will only fail if this queue is already setup or there are
no directed queues left to configure.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Add support for configuring the DLB2 hardware.
In particular, this patch configures the DLB2
hardware's scheduling domain, such that it is provisioned with
the requested number of ports and queues, provided sufficient
resources are available. Individual queues and ports are
configured later in port setup and eventdev start.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
Adds the meson build infrastructure, which includes
compile-time constants in rte_config.h. DLB2 is
only supported on Linux 64 bit X86 platforms at this time.
Adds announcement of availability for the new driver
for Intel Dynamic Load Balancer 2.0 hardware.
Signed-off-by: Timothy McDaniel <timothy.mcdaniel@intel.com>
Reviewed-by: Gage Eads <gage.eads@intel.com>
The example used the deprecated mbuf field udata64.
It is moved to a dynamic field in order to allow removal of udata64.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
The device-specific metadata was stored in the deprecated field udata64.
It is moved to a dynamic mbuf field in order to allow removal of udata64.
The name rte_security_dynfield is not very descriptive
but it should be replaced later by separate fields for each type of data
that drivers pass to the upper layer.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Add zero-copy APIs. These APIs provide the capability to
copy the data to/from the ring memory directly, without
having a temporary copy (for ex: an array of mbufs on
the stack). Use cases that involve copying large amount
of data to/from the ring can benefit from these APIs.
Signed-off-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Reviewed-by: Dharmik Thakkar <dharmik.thakkar@arm.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This example sets up a scenario that VXLAN packets can be received
by different PF queues based on VNID and each queue is bound to a VM
with a VNID so that the VM can receive its inner packets.
Usually, OVS is used to do the software encap/decap for VXLAN packets.
And the VXLAN packets offloading can be replaced with flow rules in
testpmd like Chapter "Sample VXLAN flow rules" in Testpmd Application
User Guide.
And this example hasn't been used for a long time.
So deprecate this example.
Signed-off-by: Xiaoyun Li <xiaoyun.li@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add new lookup implementation for FIB6 trie algorithm using
AVX512 instruction set
Signed-off-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Add new lookup implementation for DIR24_8 algorithm using
AVX512 instruction set
Signed-off-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Updated references to abi versions in the contributors guide.
Fixed an inaccurate reference to a symbol in the policy.
Signed-off-by: Ray Kinsella <mdr@ashroe.eu>
Reviewed-by: David Marchand <david.marchand@redhat.com>
Fields except tbl24 and tbl8 in rte_lpm structure have no
need to be exposed to the user.
Hide the unneeded exposure of structure fields for better
ABI maintainability.
Suggested-by: David Marchand <david.marchand@redhat.com>
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
Reviewed-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Acked-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Vladimir Medvedkin <vladimir.medvedkin@intel.com>
Signed-off-by: David Marchand <david.marchand@redhat.com>
Currently, users have to use external RCU mechanisms to free resources
when using lock free hash algorithm.
Integrate RCU QSBR process to make it easier for the applications to use
lock free algorithm.
Refer to RCU documentation to understand various aspects of
integrating RCU library into other libraries.
Suggested-by: Honnappa Nagarahalli <honnappa.nagarahalli@arm.com>
Signed-off-by: Dharmik Thakkar <dharmik.thakkar@arm.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Acked-by: Yipeng Wang <yipeng1.wang@intel.com>
The config options CONFIG_RTE_* are simple RTE_* defines with meson.
Now that make support is dropped, update the HPET config reference.
The comment about the AVX512 config option is not relevant anymore.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: David Marchand <david.marchand@redhat.com>
Added guide about building by using meson.
Also added the command to create virtual device.
Suggested-by: Akhil Goyal <akhil.goyal@nxp.com>
Signed-off-by: Ruifeng Wang <ruifeng.wang@arm.com>
With 'make' being removed, the patch cheatsheet needs to be updated to
remove any references to 'make'. These references have been replaced with
meson alternatives in this patch.
Signed-off-by: Kevin Laatz <kevin.laatz@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Signed-off-by: Louise Kilheeney <louise.kilheeney@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Acked-by: Nicolas Chautru <nicolas.chautru@intel.com>
While make has been deprecated for DPDK, it's still applicable for
some example apps to be built standalone, this patch adjusts the
guides to take that into consideration.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Nicolas Chautru <nicolas.chautru@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Acked-by: Lee Daly <lee.daly@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Akhil Goyal <akhil.goyal@nxp.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Bruce Richardson <bruce.richardson@intel.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Reviewed-by: Harman Kalra <hkalra@marvell.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Hyong Youb Kim <hyonkim@cisco.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
Make is no longer supported for compiling DPDK, references are now
removed in the documentation.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Reviewed-by: Kevin Laatz <kevin.laatz@intel.com>
A lot of drivers export headers, reproduce the same facility than for
libraries.
Note: this change fixes an issue with the crypto scheduler headers which
were not installed properly. A separate backport will be sent to stable
branches.
Suggested-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Fixes: 63b3907833 ("build: remove library name from version map file name")
Signed-off-by: David Marchand <david.marchand@redhat.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Replace master/slave terms in this driver.
The memory interface drivers uses a client/server architecture
so change the variable names and device arguments to that.
The previous devargs are maintained for compatibility, but if
used cause a notice in the log.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Replace master lcore with main lcore and
replace slave lcore with worker lcore.
Keep the old functions and macros but mark them as deprecated
for this release.
The "--master-lcore" command line option is also deprecated
and any usage will print a warning and use "--main-lcore"
as replacement.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Update the coding style document to include a policy against
introducing new master/slave usage. This is taken from the similar
place in the Linux kernel coding style.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
As discussed on the dpdk-dev mailing list[1], we can make some easy
improvements in standardizing the naming of the various components in DPDK,
and their associated feature-enabled macros.
Following this patch, each library will have the name in format,
'librte_<name>.so', and the macro indicating that library is enabled in the
build will have the form 'RTE_LIB_<NAME>'.
Similarly, for libraries, the equivalent name formats and macros are:
'librte_<class>_<name>.so' and 'RTE_<CLASS>_<NAME>', where class is the
device type taken from the relevant driver subdirectory name, i.e. 'net',
'crypto' etc.
To avoid too many changes at once for end applications, the old macro names
will still be provided in the build in this release, but will be removed
subsequently.
[1] http://inbox.dpdk.org/dev/ef7c1a87-79ab-e405-4202-39b7ad6b0c71@solarflare.com/t/#u
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Luca Boccassi <bluca@debian.org>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Rosen Xu <rosen.xu@intel.com>
The build-sdk-meson.rst file originates from the short plain-text meson
instructions added in 2018. Add SPDX tag and copyright notice based on the
original commit.
Fixes: 9c3adc289c ("doc: add instructions on build using meson")
Cc: stable@dpdk.org
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
When choosing a vector path to take, an extra condition must be
satisfied to ensure the max SIMD bitwidth allows for the CPU enabled
path. These checks are added in the check alg helper functions.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Tested-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
This patch adds documentation on the usage of the max SIMD bitwidth EAL
setting to enable AVX-512 at runtime.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Kevin Laatz <kevin.laatz@intel.com>
This patch adds a max SIMD bitwidth EAL configuration. The API allows
for an app to set this value. It can also be set using EAL argument
--force-max-simd-bitwidth, which will lock the value and override any
modifications made by the app.
Each arch has a define for the default SIMD bitwidth value, this is used
on EAL init to set the config max SIMD bitwidth.
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Reviewed-by: Ruifeng Wang <ruifeng.wang@arm.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
The API ``rte_security_session_create`` takes only single
mempool for session and session private data. So the
application need to create mempool for twice the number of
sessions needed and will also lead to wastage of memory as
session private data need more memory compared to session.
Hence the API is modified to take two mempool pointers
- one for session and one for private data.
This is very similar to crypto based session create APIs.
Signed-off-by: Akhil Goyal <akhil.goyal@nxp.com>
Reviewed-by: Lukasz Wojciechowski <l.wojciechow@partner.samsung.com>
Tested-by: Lukasz Wojciechowski <l.wojciechow@partner.samsung.com>
Replace '--scalar' command-line option with new one: --alg=<algname>
to allow user explicitly select desired classify method.
This is an optional parameter, if not specified default classify
algorithm will be used.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Introduces two changes into l3fwd-acl behaviour to make
it behave in the same way as l3fwd:
- Add a command-line parameter to allow the user to specify the
destination mac address for each ethernet port used.
- While forwarding the packet update source and destination mac
addresses.
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Queue stats will be removed from basic stats to xstats.
It will be PMDs responsibility to fill queue stats based on number of
queues they have.
Until all PMDs implement the xstats, a temporary
'RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS' device flag created. PMDs switched
to the xstats should clear this flag to bypass the ethdev layer autofill
for queue stats.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ray Kinsella <mdr@ashroe.eu>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Change rte_eth_dev_stop() return value from void to int
and return negative errno values in case of error conditions.
Also update the usage of the function in ethdev according to
the new return type.
Signed-off-by: Ivan Ilchenko <ivan.ilchenko@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The API function rte_eth_dev_close() was returning void.
The return type is changed to int for notifying of errors.
If an error happens during a close operation,
the status of the port is undefined,
a maximum of resources having been freed.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Liron Himi <lironh@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add command line parameter:
--rxoffs=X[,Y]
Sets the offsets of packet segments from the beginning of the
receiving buffer if split feature is engaged. Affects only the
queues configured with split offloads (currently BUFFER_SPLIT
is supported only).
Add interactive mode command, providing the same:
testpmd> set rxoffs (x[,y]*)
Where x[,y]* represents a CSV list of values, without white space.
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
