NW_MNG_IF_SEL register is a PHY link configuration register.
Add ixgbe_read_mng_if_sel_x550em to read NW_MNG_IF_SEL, validate
register values and save fields such as PHY MDIO address. This
centralises the reading and checking of the register in one place
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
The ixgbe_vf.h file did not use _<FILENAME>_ and instead used
__<FILENAME>__ which is not the standard used in every other file.
Fixes: af75078fec ("first public release")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
When there is an error getting the PHY token, the error path
fails to release the locks that it has taken. Release those
locks in that failure case.
Fixes: 86b8fb293f ("ixgbe/base: add sw-firmware sync for resource sharing on X550em_a")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch renames IXGBE_PVFTTDLEN to IXGBE_PVFTDLEN according to
abbreviation of Transmit Descriptor Length in datasheet.
Fixes: d2e72774e5 ("ixgbe/base: support X550")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch adds clearing the pool mappings when configuring default
MAC addresses for the interface. Without this there will be the risk
of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch updates ixgbe_setup_mac_link_sfp_x550a for X550 SFP+.
ixgbe_set_lan_id_multi_port_pcie has been updated to set the MAC
instance(0/1) which is needed when configuring the external PHY,
since X550a has two instances of MGPK. The MAC instance is read
from the EEPROM.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Use the method pointers instead of direct function calls for IOSF
access so that the right functions can be called on X550EM_a,
compared to other devices using the driver.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Break ixgbe_setup_eee_X550 down to better handle a change from if
statements to switch statements needed to add X550em_a KR support.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
When software sends commands to firmware using the host
slave command interface, firmware fails to receive the
command due to a checksum failed error, as the checksum is
not being correctly set by the driver software.
This patch sets command checksum to the default value of
0xFF, as per the datasheet, therefore the checksum won't
be checked by firmware.
Fixes: 86b8fb293f ("ixgbe/base: add sw-firmware sync for resource sharing on X550em_a")
Fixes: 0790adeb56 ("ixgbe/base: support X550em_a device")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
An error code indicating that the PF rejects the MAC address change
should be returned, in case that the PF has already assigned a MAC
for the VF.
Fixes: af75078fec ("first public release")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch adds new phy type and media type to support
SGMII link for X550, and add ixgbe_setup_sgmii to support
SGMII link setup.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
This patch adds two new VF requests of IXGBE_VF_GET_RETA and
IXGBE_VF_GET_RSS_KEY to the mailbox API.
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
Previously, a single VLAN header is treated as inner VLAN,
but generally, a single VLAN header is treated as the outer
VLAN header.
The patch fixes the ether type of a single VLAN type, and
enables configuring inner and outer TPID for double VLAN.
Fixes: 19b16e2f64 ("ethdev: add vlan type when setting ether type")
Signed-off-by: Beilei Xing <beilei.xing@intel.com>
made second cache line access behavior same as IA
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Reviewed-by: Jianbo Liu <jianbo.liu@linaro.org>
ixgbe PMD RX function(s) misses some packet types that are:
- correctly recognised by the underlying HW.
- marked as supported by ixgbe_dev_supported_ptypes_get().
Fixes: 9586ebd358 ("ixgbe: replace some offload flags with packet type")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Tested-by: Olivier Matz <olivier.matz@6wind.com>
When using kernel PF and DPDK VF, when the PF driver finds the link
state changes, up -> down or down -> up, the driver will send a
message to VF by mailbox. This link state change may be
triggered by PHY disconnection/reconnection, user config change
like *ifconfig down/up* or interface parameter, like MTU change.
This patch enables the support of the mailbox interrupt,
so VF driver can receive the message for link up/down.
After VF receives this message, VF port need to be reset to
recover. This needs to be handled by the application so this patch
allows the app to register a reset callback so it can reset the VF port.
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
To be consistent with the naming for ARM NEON implementation,
ixgbe_rxtx_vec.c is renamed to ixgbe_rxtx_vec_sse.c.
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Use ARM NEON intrinsic to implement ixgbe vPMD
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
[style fixes as highlighted by checkpatch.pl]
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
move scalar code which does not use x86 intrinsic functions to new file
"ixgbe_rxtx_vec_common.h", while keeping x86 code in ixgbe_rxtx_vec.c.
This allows the scalar code to to be shared among vector drivers for
different platforms.
Suggested-by: Bruce Richardson <bruce.richardson@intel.com>
Signed-off-by: Jianbo Liu <jianbo.liu@linaro.org>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The current extended ethernet statistics fetching involve doing several
string operations, which causes performance issues if there are lots of
statistics and/or network interfaces. This patch changes the test-pmd
and proc_info applications to use the new xstats API, and removes
deprecated code associated with the old API.
Signed-off-by: Remy Horton <remy.horton@intel.com>
The current extended ethernet statistics fetching involve doing several
string operations, which causes performance issues if there are lots of
statistics and/or network interfaces. This patch changes the ixgbe driver
to use the new API that seperates name string and value queries.
Signed-off-by: Remy Horton <remy.horton@intel.com>
The behavior of PKT_RX_VLAN_PKT was not very well defined, resulting in
PMDs not advertising the same flags in similar conditions.
Following discussion in [1], introduce 2 new flags PKT_RX_VLAN_STRIPPED
and PKT_RX_QINQ_STRIPPED that are better defined:
PKT_RX_VLAN_STRIPPED: a vlan has been stripped by the hardware and its
tci is saved in mbuf->vlan_tci. This can only happen if vlan stripping
is enabled in the RX configuration of the PMD.
For now, the old flag PKT_RX_VLAN_PKT is kept but marked as deprecated.
It should be removed from applications and PMDs in a future revision.
This patch also updates the drivers. For PKT_RX_VLAN_PKT:
- e1000, enic, i40e, mlx5, nfp, vmxnet3: done, PKT_RX_VLAN_PKT already
had the same meaning than PKT_RX_VLAN_STRIPPED, minor update is
required.
- fm10k: done, PKT_RX_VLAN_PKT already had the same meaning than
PKT_RX_VLAN_STRIPPED, and vlan stripping is always enabled on fm10k.
- ixgbe: modification done (vector and normal), the old flag was set
when a vlan was recognized, even if vlan stripping was disabled.
- the other drivers do not support vlan stripping.
For PKT_RX_QINQ_PKT, it was only supported on i40e, and the behavior was
already correct, so we can reuse the same bit value for
PKT_RX_QINQ_STRIPPED.
[1] http://dpdk.org/ml/archives/dev/2016-April/037837.html,
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Removed comparison against $CC in Makefiles as
in cross-compiling mode CC can be a different string
instead of string "gcc"
Suggested-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
Some architectures (ex: Power8) have a cache line size of 128 bytes,
so the drivers should not expect that prefetching the second part of
the mbuf with rte_prefetch0(&m->cacheline1) is valid.
This commit add helpers that can be used by drivers to prefetch the
rx or tx part of the mbuf, whatever the cache line size.
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Reviewed-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Many drivers provide their own implementation of rte_mbuf_raw_alloc(),
duplicating the code. Introduce a new public function in rte_mbuf to
allocate a raw mbuf (uninitialized).
Signed-off-by: Olivier Matz <olivier.matz@6wind.com>
Fix issue reported by Coverity.
Coverity ID 13193: Bad bit shift operation (BAD_SHIFT)
large_shift: In expression 1 << pool, left shifting by more than 31 bits
has undefined behavior. The shift amount, pool, is at least 32.
This patch is a rework of register addr selection logic and mask
computation to made it more readable and avoid bit overflow when 32 bit
value is shifted over its size for pool > 31.
Fixes: fe3a45fd41 ("ixgbe: add VMDq support")
Signed-off-by: Tomasz Kulasek <tomaszx.kulasek@intel.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The masking for the RX/TX enable bit was incorrect in the rx and tx
queue stop functions. Instead of using "& MASK" it used "| MASK" which
would always return true. This error was found by converity scan.
CID 13215 : Wrong operator used (CONSTANT_EXPRESSION_RESULT)
operator_confusion: txdctl | 33554432 is always 1/true regardless of the
values of its operand. This occurs as the logical second operand of
'&&'.
CID 13216 : Wrong operator used (CONSTANT_EXPRESSION_RESULT)
operator_confusion: rxdctl | 33554432 is always 1/true regardless of the
values of its operand. This occurs as the logical second operand of
'&&'.
Coverity issue: 13215
Coverity issue: 13216
Fixes: 029fd06d40 ("ixgbe: queue start and stop")
Signed-off-by: Piotr Azarewicz <piotrx.t.azarewicz@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Run ixgbe driver through checkpatch and fix the issues highlighted
Fix line spacing, some bad indentation, and in a couple
of cases use short circuit (already there) return to lessen indentation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Applied with four additional fixes for issues highlighted by checkpatch
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Some statistics were deprecated since release 2.1 (49f386542a).
The last deprecated counter to be used was imcasts.
The VF loopback statistics are also removed as they are used only
in igb and duplicated in extended statistics.
The new counters should be added to extended statistics.
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Acked-by: Remy Horton <remy.horton@intel.com>
VxLAN & NVGRE are supported by x550. As we know HW can parse
the packet and tell SW the type info. For VxLAN & NVGRE packets
there's some change. HW will not tell SW the info of the outer
header but the inner header instead. But we always take the
info as it's for the outer header. So the packet type info is
not right when x550 receives VxLAN & NVGRE packets.
As x550 only supports IPv4 VxLAN & NVGRE packets, we can tell
the outer header of VxLAN is IPv4 + UDP, and the outer header
of NVGRE is IPv4 only. What we don't know is if there's
optional field in the outer IPv4 header.
This patch implement the support of packet type for VxLAN &
NVGRE. And it fixes the wrong packet type issue either.
BTW:
It doesn't fix any existing commit as although it resolve an
issue it's more like a new feature but not a fix.
Reported-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
This patch redesigns the API to set the link speed/s configuration
of an ethernet port. Specifically:
- it allows to define a set of advertised speeds for
auto-negociation.
- it allows to disable link auto-negociation (single fixed speed).
- default: auto-negociate all supported speeds.
A flag autoneg in struct rte_eth_link indicates if link speed was a
result of auto-negociation or was fixed by configuration.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Tested-by: Nelio Laranjeiro <nelio.laranjeiro@6wind.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Tested-by: Beilei Xing <beilei.xing@intel.com>
Tested-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
The speed capabilities of a device can be retrieved with
rte_eth_dev_info_get().
The new field speed_capa is initialized in the drivers without
taking care of device characteristics in this patch.
When the capabilities of a driver are accurate, the table in
overview.rst must be filled.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
The speed numbers ETH_LINK_SPEED_ are renamed ETH_SPEED_NUM_.
The prefix ETH_LINK_SPEED_ is kept for AUTONEG and will be used
for bit flags in next patch.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Some duplex values are replaced from 0 to half-duplex when link is down.
Some drivers are still using their own constants for duplex modes.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Define and use ETH_LINK_UP and ETH_LINK_DOWN where appropriate.
Signed-off-by: Marc Sune <marcdevel@gmail.com>
Signed-off-by: Thomas Monjalon <thomas.monjalon@6wind.com>
Silence a compiler warning that this variable may be used uninitialized.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
Tell the compiler to use an unsigned constant for the config shifts.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Panu Matilainen <pmatilai@redhat.com>
Acked-by: Helin Zhang <helin.zhang@intel.com>
The lower 16 bits of EICR register are used for queue interrupts,
dpdk framework take over the first bit for other interrupts like
LSC, so there're only 15 bits left for queue interrupts mapping.
This patch adds a check for the num of interrupt queues at
dev_start.
Signed-off-by: Wang Xiao W <xiao.w.wang@intel.com>
Acked-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
When starting testpmd with multiple queues on a ixgbe VF
port, it failed with this printing, "nb_rxq(4) is greater
than max_rx_queues(1)".
The root cause is the VF doesn't get the right max rx queue
number from PF and it uses the default value 1.
VF max rx queue number is set by PF through mailbox messages.
The message for this setting only supports version 1.1. As
message version is updated to 1.2, VF cannot parse the rx queue
number setting message correctly.
This patch raise a specific base code update for this issue.
Fixes: 72dec9e37a ("ixgbe: support multicast promiscuous mode on VF")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
l2 tunnel and e-tag are not supported on the new x550em_a NICs, due
to missing checks for that mac type in the code.
This patch adds in the necessary conditional checks to enable the features
for x550em_a.
Fixes: 22e77d4501 ("ixgbe: support L2 tunnel operations")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
An issue is found on x550em NICs: ieee1588 is not working, the time is
always reported as 0.
The root cause is that the timer is only supported by the driver for x550,
switch statement entries are missing for x550em_x and x550em_a. This patch
adds those missing entries.
Fixes: a7740dc130 ("ixgbe: support new devices and MAC types")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
icc (icc (ICC) 16.0.1 20151021) is generating following compile error:
CC ixgbe_rxtx.o
.../drivers/net/ixgbe/ixgbe_rxtx.c(153): error #3656: variable
"free" may be used before its value is set
(nb_free > 0 && m->pool != free[0]->pool)) {
^
Indeed this is a false positive and code is correct.
"nb_free" check prevents the free[] access before its value set.
Disabling this icc warning (#3656) for file ixgbe_rxtx.c.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Ixgbe HW supports 128 TX queues. However, the full 128 queues are only
available in VT and DCB mode. In normal default "none" mode (VT/DCB off)
the maximum number of available queues is only 64.
The driver doesn't check the mode when reporting the available
number of queues, allowing more that 64 queues to be used in all cases.
If a queue no. >=64 is used in default mode, the TX packets will be dropped
silently.
This change adds a check to forbid using a queue number larger than 64
during device configuration (in default mode), so that the problem is
reported as early as possible.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
Internal variable containing the number of TX queues for a device,
was being incorrectly assigned the number of RX queues, instead of TX.
Fixes: 27b609cbd1 ("ethdev: move the multi-queue mode check to specific drivers")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Acked-by: John McNamara <john.mcnamara@intel.com>
There's an issue reported. In the scenario DPDK PF + DPDK VF,
if the VF port is closed, PF port cannot receive packets.
I found at that time the promicuous mode is disabled on the PF
port. But it should be enabled.
When VF port is closed, it will send a message to its PF port to
reset it. During this, PF port will also reset its own
promicuous mode. Which promiscuous mode should be set depends on
the parameter stored in the device data. In the function
set_rx_mode, the pointer of device data points to the wrong
address. So, the promiscuous mode is wrong.
Fixes: 00e30184da ("ixgbe: add PF support")
Signed-off-by: Wenzhuo Lu <wenzhuo.lu@intel.com>
Reported-by: Bernard Iremonger <bernard.iremonger@intel.com>
Acked-by: Jingjing Wu <jingjing.wu@intel.com>
Current vector RX can't always set the packet_type properly.
To be more specific:
a) it never sets RTE_PTYPE_L2_ETHER
b) it doesn't handle tunnel ipv4/ipv6 case correctly.
c) it doesn't check is IXGBE_RXDADV_PKTTYPE_ETQF set or not.
While a) is pretty easy to fix, b) and c) are not that straightforward
in terms of SIMD ops (specially b).
So far I wasn't able to make vRX support packet_type properly without
noticeable performance loss.
So for now, just remove that functionality from vector RX and
update dev_supported_ptypes_get().
Fixes: 3962541758 ("mbuf: redefine packet type")
Signed-off-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Acked-by: Cunming Liang <cunming.liang@intel.com>
