Add support for forced ethernet speed setting.
Currently testpmd tries to configure the Ethernet port in autoneg mode.
It is not possible to set the Ethernet port to a specific speed while
starting testpmd. In some cases capability to configure a forced speed
for the Ethernet port during initialization may be necessary. This patch
tries to add this support.
The patch assumes full duplex setting and does not attempt to change that.
So speeds like 10M, 100M are not configurable using this method.
The command line to configure a forced speed of 10G:
dpdk-testpmd -c 0xff -- -i --eth-link-speed 10000
The command line to configure a forced speed of 50G:
dpdk-testpmd -c 0xff -- -i --eth-link-speed 50000
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
The normal operation of devices with copper phys depends on the
initialization and configuration of the PHY chip. The task of
driving the PHY chip is implemented in some firmware versions.
If firmware supports the phy driver, it will report a capability
flag to driver in probing process. The driver determines whether
to support PF device with copper phys based on the capability bit.
If supported, the driver set a flag indicating that the firmware
takes over the PHY, and then the firmware initializes the PHY.
This patch supports the query of link status and link info, and
existing basic features for PF device with copper phys.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch add support tx_done_cleanup ops, which could support for
the API rte_eth_tx_done_cleanup to free consumed mbufs on Tx ring.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
This patch add support for dumping module EEPROM.
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Rename PKT_RX_EIP_CKSUM_BAD to PKT_RX_OUTER_IP_CKSUM_BAD and
deprecate the original name. The new name is better aligned
with existing PKT_RX_OUTER_* flags, which should help reduce
confusion about its use.
Suggested-by: Ferruh Yigit <ferruh.yigit@intel.com>
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Some Rx/Tx operations like queue setup and release, packet type get, and
Tx done cleanup have been supported on PF device. There are ops
functions directly added.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Configure VF device with RX port. Initialize receive and transmit unit,
set the receive and transmit functions. And support to check the
status of RX and TX descriptors.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Add information get operation for VF device.
RX and TX offload capabilities are same as the PF device.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Generate a random MAC address if none was assigned by PF during
the initialization of VF device. And support to add and remove
MAC address.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Introduce virtual function driver in txgbe PMD,
add simple init and uninit function to probe and remove the device.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
In case error packets are received by the Ethernet interface,
this patch enables receiving packets on the error queue,
printing the error and the error packet.
To enable, use the dev_arg as : fslmc:dpni.1,drv_error_queue=1
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Add support for dev arg ``fslmc:dpni.1,drv_tx_conf=1``
It is optional for dpaa2 to use TX confirmation. DPAA2
can free the transmitted packets. However some use-case
requires the TX confirmation to be explicit.
Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Add basic support for scheduling and shaping on dpaa2
platform.
HW supports 2 level of scheduling and shaping.
However the current patch only support single level.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
"show port cap all|<port_id>" was to display offload configuration of
port(s).
But later two other commands added to show same information in more
accurate way:
show port (port_id) rx_offload configuration
show port (port_id) tx_offload configuration
These new commands can both show port and queue level configuration,
also with their capabilities counterparts easier to see offload
capability and configuration of the port in similar syntax.
So the functionality is duplicated and removing this version, to favor
the new commands.
Another problem with this command is it requires each new offload to be
added into the function to display them, and there were missing offloads
that are not displayed, this requirement for sure will create gaps by
time as new offloads added.
Signed-off-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
Add support for displaying the count of used (filled by hardware
but not yet processed by the driver) descriptors on a receive
queue in order to allow the rte_eth_dev rx_queue_count() API to
be exercised and tested.
Signed-off-by: Lance Richardson <lance.richardson@broadcom.com>
Acked-by: Xiaoyun Li <xiaoyun.li@intel.com>
In order to save DMA entries limited by kernel both for external
memory and hugepage memory, an attempt was made to map physically
contiguous memory in one go. This cannot be done as VFIO IOMMU type1
does not support partially unmapping a previously mapped memory
region while Heap can request for multi page mapping and
partial unmapping.
Hence for going back to old method of mapping/unmapping at
memseg granularity, this commit reverts
commit d1c7c0cdf7ba ("vfio: map contiguous areas in one go")
Also add documentation on what module parameter needs to be used
to increase the per-container dma map limit for VFIO.
Fixes: d1c7c0cdf7ba ("vfio: map contiguous areas in one go")
Cc: stable@dpdk.org
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Acked-by: Anatoly Burakov <anatoly.burakov@intel.com>
Acked-by: David Christensen <drc@linux.vnet.ibm.com>
Start a new release cycle with empty release notes.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: David Marchand <david.marchand@redhat.com>
The build tool pmdinfogen was rewritten in DPDK 21.02,
adding Windows support.
There is a new build-time dependency: pyelftools.
Fixes: f0f93a7adfee ("buildtools: use Python pmdinfogen")
Fixes: 6b19edcb663c ("build: enable pmdinfogen for Windows")
Signed-off-by: Dmitry Kozlyuk <dmitry.kozliuk@gmail.com>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
python-pyelftools is not packaged for RHEL/CentOS with
the exception of RHEL7 EPEL.
Add command to install it with pip.
Fixes: f0f93a7adfee ("buildtools: use Python pmdinfogen")
Signed-off-by: Kevin Traynor <ktraynor@redhat.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The tool dpdk-hugepages.py, added in DPDK 20.11,
is referenced in the guides instead of more complicate commands.
The original Linux commands are kept in linux_gsg/sys_reqs.rst
and nics/build_and_test.rst.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
replace testpmd with dpdk-testpmd in all commands
because on compilation through meson, dpdk-testpmd is the default
application name.
Signed-off-by: Sarosh Arif <sarosh.arif@emumba.com>
Acked-by: Bruce Richardson <bruce.richardson@intel.com>
The zero value in flow MARK action is reported in Rx datapath
as tagged with zero FDIR ID. Once packet is marked in flow engine
it will be always reported as tagged. For metadata only the zero
value means there is "no metadata" in the packet and the metadata
flag is not set for the case.
Fixes: 3ceeed9f7855 ("doc: update flow mark action in mlx5 guide")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
There is an 82599 errata that UDP frames with a zero checksum are
incorrectly marked as checksum invalid by the hardware. This was
leading to misleading PKT_RX_L4_CKSUM_BAD flag.
This patch changes the bad UDP checksum to PKT_RX_L4_CKSUM_UNKNOWN,
so the software application will then have to recompute the checksum
itself if needed.
Bugzilla ID: 629
Fixes: af75078fece3 ("first public release")
Cc: stable@dpdk.org
Reported-by: Paolo Valerio <pvalerio@redhat.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Konstantin Ananyev <konstantin.ananyev@intel.com>
Tested-by: Paolo Valerio <pvalerio@redhat.com>
The "rte_telemetry_init()" function is for use by "rte_eal_init()" and
should not be part of the public API. Mark it as internal only.
Fixes: 6dd571fd07c3 ("telemetry: introduce new functionality")
Cc: stable@dpdk.org
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
The guide for using the crypto perf graphing script had some incorrect
indentation, unnecessary blank lines, and a missing argument in one of
the usage examples. These are corrected in this patch.
Fixes: f400e0b82bf1 ("app/crypto-perf: add script to graph perf results")
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
Add release note for the new crypto perf graphing script.
Fixes: f400e0b82bf1 ("app/crypto-perf: add script to graph perf results")
Signed-off-by: Ciara Power <ciara.power@intel.com>
Acked-by: Adam Dybkowski <adamx.dybkowski@intel.com>
This sets the correct minimal requirements for these features:
- Buffer Split offload is supported/verified on ConnectX-5
- Tx scheduling requires ConnectX-6DX and depends on firmware version
Fixes: cb7b0c24c835 ("doc: update hardware offloads support in mlx5 guide")
Cc: stable@dpdk.org
Signed-off-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Reviewed-by: Asaf Penso <asafp@nvidia.com>
Verbs cannot be used to configure newly introduced miniCQE formats for
Flow Tag and L3/L4 Header compression. Support for these formats has
been added to the DevX configuration only. And the RX queue descriptor
has been updated with the CQE compression format information only as
well. But the datapath relies on this info no matter which method is
used for Rx queues configuration. Set proper CQE compression format
information in the Verbs configuration to fix the miniCQE parsing logic.
Fixes: 54c2d46b160f ("net/mlx5: support flow tag and packet header miniCQEs")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Added more information of shared action on
how to update, query, and the benefits.
Signed-off-by: Xiaoyu Min <jackmin@nvidia.com>
Acked-by: Ori Kam <orika@nvidia.com>
Reviewed-by: Asaf Penso <asafp@nvidia.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Add documentation to support i40e PMD on Windows.
Update the release notes and features list for the same.
Signed-off-by: Pallavi Kadam <pallavi.kadam@intel.com>
Reviewed-by: Ranjit Menon <ranjit.menon@intel.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Here fixes the Kunpeng introduction address link with hns3.rst
Fixes: 565829db8b8f ("net/hns3: add build and doc infrastructure")
Cc: stable@dpdk.org
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Document FEC in NIC features, add information about FEC and add
implementation related support.
Fixes: b7ccfb09da95 ("ethdev: introduce FEC API")
Fixes: 9bf2ea8dbc65 ("net/hns3: support FEC")
Fixes: 62aafe035896 ("net/cxgbe: support configuring link FEC")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Currently, X722 firmware doesn't support to add more than
one mirror rule in one VSI.
Signed-off-by: Lingyu Liu <lingyu.liu@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
