The admin-configured vNIC settings (i.e. via CIMC or UCSM) now include
Geneve offload. Use that setting to decide whether to enable or
disable Geneve offload and remove the devarg 'geneve-opt'.
Also, the firmware now allows the driver to change the Geneve port
number. So extend udp_tunnel_port_{add,del} to accept Geneve port, in
addition to VXLAN.
Fixes: 93fb21fdbe23 ("net/enic: enable overlay offload for VXLAN and GENEVE")
Cc: stable@dpdk.org
Signed-off-by: John Daley <johndale@cisco.com>
Reviewed-by: Hyong Youb Kim <hyonkim@cisco.com>
This patch adds more description for hns3 PMD document, that is:
'Sample Application Notes', 'Statistics','Performance tuning'.
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
After creating a connection tracking context, it can be used between
two ports. For each port, the flow for one direction traffic will
be created.
The context can only be shared between the owner port and the peer
port that was specified when being created. Only the owner port
could update the context or query it in current implementation.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Allocating a CT from the management pools and creating the DR actions
for both directions by default.
If there is no available connection tracking action, a new pool will
be created with a fixed size bulk allocation. Right now, all the
resources are controlled by the linked list.
The ASO connection tracking context associated with these actions
need to be updated via WQE before using for steering.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Based on the capacity, 3 registers could be used. Due to the register
allocation, only the one REG_C_3 for meter color could be reused
right now.
Then in the same flow, no more than one ASO action can be supported.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
During startup, the ASO connection tracking offload capability could
be queried via HCA_CAP_QUERY command. If the HW doesn't support ASO
CT, the value would be 0 by default. The following initialization
should be skipped and the creation of the CT object should return
a failure directly.
The following CT creation should also check this capability. With
the old driver, the pre-processing macro should be used in order to
make the compiling pass.
Signed-off-by: Bing Zhao <bingz@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
MLX5 PMD supports the following integrity filters for outer and
inner network headers:
- l3_ok
- l4_ok
- ipv4_csum_ok
- l4_csum_ok
`level` values 0 and 1 reference outer headers.
`level` > 1 reference inner headers.
Flow rule items supplied by application must explicitly specify
network headers referred by integrity item. For example:
flow create 0 ingress
pattern
integrity level is 0 value mask l3_ok value spec l3_ok /
eth / ipv6 / end …
or
flow create 0 ingress
pattern
integrity level is 0 value mask l4_ok value spec 0 /
eth / ipv4 proto is udp / end …
Signed-off-by: Gregory Etelson <getelson@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Existing API supports counter action to count traffic of a single flow.
The user can share the count action among different flows using the
shared flag and the same counter ID in the count action configuration.
Recent patch [1] introduced the indirect action API.
Using this API, an action can be created as indirect, unattached to any
flow rule.
Multiple flows can then be created using the same indirect action.
The new API also supports query operation of an indirect action.
The new API is more efficient because the driver gets it's own handler
for the count action instead of managing a mapping between the user ID
to the driver handle.
Support create, query and destroy indirect action operations for flow
count action.
Application will use the indirect action query operation to query this
count action.
In the meantime the old sharing mechanism (with the sharing flag)
continues to be supported, and the user can choose the way he wants to
share the counter.
The new indirect action API is only supported in DevX, so sharing
counter action in Verbs can only be done through the old mechanism.
[1] https://mails.dpdk.org/archives/dev/2020-July/174110.html
Signed-off-by: Michael Baum <michaelba@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
All rights reserved by Beijing Wangxun Technology Co., Ltd.
Part of the code references Intel.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Currently meter algorithms only supports bytes units for meter profiles.
Using ASO feature, the driver can support metering in per packet units.
Add support for packet units in meter profiles.
Signed-off-by: Li Zhang <lizh@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
Currently ASO meter must be followed by policy table, so this adds
the support that connecting meter and policy table.
There are several cases to be considered:
1. For non-termination policy, connect meter to the default policy
table.
2. For non-RSS termination policy case, simply get the policy
table id and connect meter to it.
3. For RSS termination policy case, need to split the flow due
to RSS info in policy, and translate each sub-flow using that RSS,
then create the sub policy table to be connected.
4. In termination policy case, if there's no actions to modify the
packet before meter, no need to use set_tag to save meter id in
register. Only add a new flow in drop table using the same match
criteria as suf-flow, to save cache miss.
Signed-off-by: Shun Hao <shunh@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
This patch added examples for runtime config options, to help user
how to use this.
Fixes: a124f9e9591b ("net/hns3: add runtime config to select IO burst function")
Fixes: 70791213242e ("net/hns3: support masking device capability")
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Fix up the suffix of the PCI ID to be consistent with the code.
Fixes: 979f2bae0714 ("doc: improve multiport PF in nfp guide")
Cc: stable@dpdk.org
Signed-off-by: Chaoyong He <chaoyong.he@corigine.com>
Signed-off-by: Heinrich Kuhn <heinrich.kuhn@netronome.com>
Fix typos in the names of kernel drivers based on UIO,
and make sure the generic term for the interface is UIO in capitals.
Fixes: 3a78b2f73206 ("doc: add virtio crypto PMD guide")
Fixes: 3cc4d996fa75 ("doc: update VFIO usage in qat crypto guide")
Fixes: 39922c470e3c ("doc: add known uio_pci_generic issue for i40e")
Fixes: 86fa6c57a175 ("doc: add known igb_uio issue for i40e")
Fixes: beff6d8e8e2e ("net/netvsc: add documentation")
Cc: stable@dpdk.org
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Meter statistics are each policer action each counter.
Totally 4 counters per each meter.
It causes cache missed
and lead to data forwarding performance low.
To optimize it, support pass counter for green
and drop counter for red.
Totally two counters per each meter.
Also use the global drop statistics for
all meter drop action.
Limitations as below:
1. It does not support yellow counter and return 0.
2. All the meter colors with drop action will be
counted only by the global drop statistics.
3. Red color must be with drop action.
Signed-off-by: Li Zhang <lizh@nvidia.com>
Acked-by: Matan Azrad <matan@nvidia.com>
The patch 'net/hns3: rename Rx burst function' changed `simple'
Rx function name from 'scalar' to 'scalar simple', but doc
ignored that.
This patch fixed it.
Fixes: aa5baf47e1a3 ("net/hns3: rename Rx burst function")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The i40evf PMD will be deprecated, iavf will be the only VF driver for
Intel 700 serial (i40e) NIC family.
To reach this, there will be 2 steps:
Step 1: iavf will be the default VF driver, while i40evf still can be
selected by devarg: "driver=i40evf".
This is covered by this patch, which include:
1) add all 700 serial NIC VF device ID into iavf PMD
2) skip probe if devargs contain "driver=i40evf" in iavf
3) continue probe if devargs contain "driver=i40evf" in i40evf
Step 2: i40evf and related devarg are removed, this will happen at DPDK
21.11
Between step 1 and step 2, no new feature will be added into i40evf
except bug fix.
Signed-off-by: Robin Zhang <robinx.zhang@intel.com>
Acked-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Ferruh Yigit <ferruh.yigit@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
This patch supports runtime config of mask device capability, it was
used to mask the capability which queried from firmware.
The device argument key is "dev_caps_mask" which takes hexadecimal
bitmask where each bit represents whether mask corresponding capability.
Its main purpose is to debug and avoid problems.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
This patch fixes HiSilicon copyright syntax.
According to the suggestion of our legal department,
to standardize the copyright license of our code to
avoid potential copyright risks, we make a unified
modification to the "Hisilicon", which was nonstandard,
in the main modules we maintain.
We change it to "HiSilicon", which is consistent with
the terms used on the following official website:
https://www.hisilicon.com/en/terms-of-use.
Fixes: 565829db8b8f ("net/hns3: add build and doc infrastructure")
Cc: stable@dpdk.org
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
The speed capability of the device can be reported to the upper-layer app
in rte_eth_dev_info_get API. In this API, the speed capability is derived
from the 'supported_speed', which is the speed capability actually
supported by the NIC. The value of the 'supported_speed' is obtained
once in the probe stage and may be updated in the scheduled task to deal
with the change of the transmission interface.
Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Previous implementations support dump all the flows. Add new arg
rte_flow in rte_flow_dev_dump to dump one flow.
Signed-off-by: Haifei Luo <haifeil@nvidia.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Ori Kam <orika@nvidia.com>
Updates the documentation for push/pop VLAN support. In E-Switch
mode, push VLAN on ingress traffic and pop VLAN in egress traffic
are both support.
Signed-off-by: Dong Zhou <dongzhou@nvidia.com>
Reviewed-by: Asaf Penso <asafp@nvidia.com>
Currently, PF driver will report lsc when it detects the link status
change, it's not a generic implementation.
We refactor PF lsc event report by following scheme:
1. PF driver marks RTE_PCI_DRV_INTR_LSC in rte_pci_driver by default.
2. In the init stage, PF driver will detect whether firmware supports
lsc interrupt or not, driver will clear RTE_ETH_DEV_INTR_LSC flag if
firmware doesn't support lsc interrupt.
3. PF driver will report lsc event only when dev_conf.intr_conf.lsc is
set.
Note: If the firmware supports lsc interrupt, we also keep periodic
polling to deal with the interrupt loss.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, VF driver periodically obtains link status from PF kernel
driver, and reports lsc event when detects link status change. Because
the period is 1 second, it's probably too late to report especially
in such as bonding scenario.
To solve this problem we use the following scheme:
1. PF kernel driver support immediate push link status to all VFs when
it detects the link status changes.
2. VF driver will detect PF kernel driver whether support push link
status in device init stage by sending request link info mailbox
message to PF, PF then tell VF the push capability by extend
HNS3_MBX_LINK_STAT_CHANGE mailbox message.
3. VF driver marks RTE_PCI_DRV_INTR_LSC in rte_pci_driver by default,
when it detects PF doesn't support push link status then it will clear
RTE_ETH_DEV_INTR_LSC flag.
So if PF kernel driver supports push link status to VF, then VF driver
will have RTE_ETH_DEV_INTR_LSC capability.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Action port_id was not supported until now.
In this patch the action port_id supports passing from input
port PF to output port which is one of input port respective VF
Signed-off-by: Smadar Fuks <smadarf@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add support for NVGRE encap as a sample action
and validate it.
Signed-off-by: Salem Sol <salems@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Add support for VXLAN encap as a sample action
and validate it.
Signed-off-by: Salem Sol <salems@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Kernel driver 2.13.10 is removed, so update recommended matching list
for i40e.
Cc: stable@dpdk.org
Signed-off-by: Robin Zhang <robinx.zhang@intel.com>
Acked-by: Beilei Xing <beilei.xing@intel.com>
Disable loading of external DDP package as it is not
supported on Windows.
Signed-off-by: Pallavi Kadam <pallavi.kadam@intel.com>
Reviewed-by: Ranjit Menon <ranjit.menon@intel.com>
Acked-by: Jie Zhou <jizh@microsoft.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
- Add Intel ice PMD support on Windows.
- Remove #include sys/ioctl header file as it is not needed.
- Replace x86intrin.h with rte_vect.h to avoid __m_prefetchw conflicting
types.
- Replace POSIX usleep() API with rte API.
- Add a new macro for the access() API as the original function
has been deprecated on Windows.
- Add extra cflags '-fno-asynchronous-unwind-tables'
to avoid MinGW build error:
Error: invalid register for .seh_savexmm
- Add documentation to support ice PMD on Windows.
Update the release notes and features list for the same.
Signed-off-by: Pallavi Kadam <pallavi.kadam@intel.com>
Reviewed-by: Ranjit Menon <ranjit.menon@intel.com>
Acked-by: Jie Zhou <jizh@microsoft.com>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
PMDs use RTE_LIBRTE_<PMD_NAME>_DEBUG_RX|TX as build option to wrap
data path debug code. As .config has been removed since the meson build,
It is not friendly for new DPDK users to notice those debug options.
The patch introduces below build options for data path debug, so PMD
can choose to reuse them to avoid maintain their own.
- RTE_ETHDEV_DEBUG_RX
- RTE_ETHDEV_DEBUG_TX
All the build options are documented at programming guide
"3.1 Driver Option", so users can easily find them.
The original undocumented RTE_LIBRTE_ETHDEV_DEBUG will alias to
both RTE_ETHDEV_DEBUG_RX and RTE_ETHDEV_DEBUG_TX for backward
compatibility.
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Acked-by: Thomas Monjalon <thomas@monjalon.net>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Modification of the 802.1Q Tag Identifier, VXLAN Network
Identifier or GENEVE Network Identifier is not supported.
Reject attempt to modify these fields via the MODIFY_FIELD
action and document this mlx5 driver limitation.
Fixes: 641dbe4fb053 ("net/mlx5: support modify field flow action")
Cc: stable@dpdk.org
Signed-off-by: Alexander Kozyrev <akozyrev@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
To probe representors from different kernel bonding PFs, had to specify
2 separate devargs like this:
-a 03:00.0,representor=pf0vf[0-3] -a 03:00.0,representor=pf1vf[0-3]
This patch supports range or list of PF section in devargs, so the
alternative short devargs of above is:
-a 03:00.0,representor=pf[0-1]vf[0-3]
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
To probe representor on 2nd PF of kernel bonding device, had to specify
PF1 BDF in devarg:
<PF1_BDF>,representor=0
When closing bonding device, all representors had to be closed together
and this implies all representors have to use primary PF of bonding
device. So after probing representor port on 2nd PF, when locating new
probed device using device argument, the filter used 2nd PF as PCI
address and failed to locate new device.
Conflict happened by using current representor devargs:
- Use PCI BDF to specify representor owner PF
- Use PCI BDF to locate probed representor device.
- PMD uses primary PCI BDF as PCI device.
To resolve such conflicts, new representor syntax is introduced here:
<primary BDF>,representor=pfXvfY
All representors must use primary PF as owner PCI device, PMD internally
locate owner PCI address by checking representor "pfX" part. To EAL, all
representors are registered to primary PCI device, the 2nd PF is hidden
to EAL, thus all search should be consistent.
Same to VF representor, HPF (host PF on BlueField) uses same syntax to
probe, example: representor=pf1vf[0-3,-1]
This patch also adds pf index into kernel bonding representor port name:
<BDF>_<ib_name>_representor_pf<X>vf<Y>
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
This patch adds support for SF representor. Similar to VF representor,
switch port name of SF representor in phys_port_name sysfs key is
"pf<x>sf<y>".
Device representor argument is "representors=sf[list]", list member
could be mix of instance and range. Example:
representors=sf[0,2,4,8-12,-1]
To probe VF representor and SF representor, need to separate into 2
devices:
-a <BDF>,representor=vf[list] -a <BDF>,representor=sf[list]
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Add device arguments to support runtime options.
And use these configuration to control the link setup flow, to adapt to
different NIC's construction. Use firmware version to control the impact
of firmware update. And fix some left bugs.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Since rte_flow is the only API for filtering operations,
the legacy driver interface filter_ctrl was too much complicated
for the simple task of getting the struct rte_flow_ops.
The filter type RTE_ETH_FILTER_GENERIC and
the filter operarion RTE_ETH_FILTER_GET are removed.
The new driver callback flow_ops_get replaces filter_ctrl.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Acked-by: Haiyue Wang <haiyue.wang@intel.com>
Acked-by: Rosen Xu <rosen.xu@intel.com>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Reviewed-by: Andrew Rybchenko <andrew.rybchenko@oktetlabs.ru>
Reviewed-by: Ferruh Yigit <ferruh.yigit@intel.com>
Updates the documentation for supported sample actions in the NIC Rx
and E-Switch steering flow.
Signed-off-by: Jiawei Wang <jiaweiw@nvidia.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@nvidia.com>
Add support for rte_flow_item_raw to parse custom L2 and L3 protocols.
Signed-off-by: Satheesh Paul <psatheesh@marvell.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Add support for query Rx descriptor status in hns3 driver. Check the
descriptor specified and provide the status information of the
corresponding descriptor.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Add support for query Tx descriptor status in hns3 driver. Check the
descriptor specified and provide the status information of the
corresponding descriptor.
Signed-off-by: Hongbo Zheng <zhenghongbo3@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
Currently, the driver support multiple IO burst function and auto
selection of the most appropriate function based on offload
configuration.
Most applications such as l2fwd/l3fwd don't provide the means to
change offload configuration, so it will use the auto selection's io
burst function.
This patch support runtime config to select io burst function, which
add two config: rx_func_hint and tx_func_hint, both could assign
vec/sve/simple/common.
The driver will use the following rules to select io burst func:
a. if hint equal vec and meet the vec Rx/Tx usage condition then use the
neon function.
b. if hint equal sve and meet the sve Rx/Tx usage condition then use the
sve function.
c. if hint equal simple and meet the simple Rx/Tx usage condition then
use the simple function.
d. if hint equal common then use the common function.
e. if hint not set then:
e.1. if meet the vec Rx/Tx usage condition then use the neon function.
e.2. if meet the simple Rx/Tx usage condition then use the simple
function.
e.3. else use the common function.
Note: the sve Rx/Tx usage condition based on the vec Rx/Tx usage
condition and runtime environment (which must support SVE).
In the previous versions, driver will preferred use the sve function
when meet the sve Rx/Tx usage condition, but in this case driver could
get better performance if use the neon function.
Signed-off-by: Chengwen Feng <fengchengwen@huawei.com>
Signed-off-by: Min Hu (Connor) <humin29@huawei.com>
When link goes down, disable the port's Rx path to drop the incoming
traffic closer to the wire, instead of accepting them in for further
Rx processing, only to eventually drop them at the port's RxQs. This
prevents unnecessary congestion in the Rx path. The port's Rx path
will be re-enabled once the link up event is received in the firmware
event queue.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
