Rx queue setup function checks configured MTU to make sure that
no oversized packets can be received. But a following call to
set MTU function might make this check irrelevant.
Add a function to check MTU size against Rx buffer size and
additional Rx queue info, including Rx scatter offload.
Fixes: e961cf425e ("net/sfc: support MTU change")
Cc: stable@dpdk.org
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
As stated in the deprecation notice from December 2016,
"the legacy filter API, including rte_eth_dev_filter_supported(),
rte_eth_dev_filter_ctrl() as well as filter types MACVLAN, ETHERTYPE,
FLEXIBLE, SYN, NTUPLE, TUNNEL, FDIR, HASH and L2_TUNNEL, is superseded
by the generic flow API (rte_flow)".
After a long wait of more than two years, the legacy filter API
is marked as deprecated, while still tested with testpmd and
the tep_termination example.
The next step will be to announce a deadline for complete removal.
As preparation of the removal of rte_eth_ctrl.h,
RTE_ETH_FLOW_*, RTE_TUNNEL_TYPE_* and RTE_ETH_HASH_FUNCTION_* definitions
are moved to rte_ethdev.h and rte_flow.h.
Signed-off-by: Thomas Monjalon <thomas@monjalon.net>
Acked-by: Shahaf Shuler <shahafs@mellanox.com>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Acked-by: Jerin Jacob <jerinj@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Hemant Agrawal <hemant.agrawal@nxp.com>
Acked-by: Adrien Mazarguil <adrien.mazarguil@6wind.com>
Acked-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Rx refill in one bulk (which is just 8 descriptors) by default is too
aggressive and makes too many MMIO writes (Rx doorbells) if packet rate
is high. Setting default to 1/8 of Rx descriptors number shows good
performance results. Anyway it is a default value which may be
overridden by Rx configuration provided by application.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Handle VXLAN and GENEVE TSO on EF10 native Tx datapath.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Said message cannot be considered as warning since
the PMD anyway reports available offload capabilities
by means of device info interface. Make this log
message informational and improve its formatting
by placing the text itself on the same line.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
As a result, code duplication will be avoided in the current
TSO implementations (EFX and EF10 native). The future patch to
add support for tunnel TSO will also reuse the new function.
Signed-off-by: Ivan Malov <ivan.malov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Make Tx prepare function able to detect packets with invalid header
size when header linearization is required.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Add descriptor space check to Tx prepare function to inform a caller
that a packet that needs more than maximum Tx descriptors of a queue
can not be sent.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Tx offloads checks should be done in Tx prepare.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Implement tx_prepare callback. The implementation checks for anything
only in RTE debug mode. No checks are done otherwise because EF10
simple datapath ignores Tx offloads.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Implement tx_prepare callback and update Tx burst function accordingly.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Implement generic checks in Tx prepare function and update Tx burst
function accordingly.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Numbers of extra descriptors required for TSO are EF10-specific
in fact. Highlight it in define names.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Move the check inside xmit function to the branch in which
the check is mandatory. It makes case when TSO header is not
fragmented a bit more faster.
Fixes: 6bc985e411 ("net/sfc: support TSO in EF10 Tx datapath")
Cc: stable@dpdk.org
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Move the check inside xmit function to the branch in which
the check is mandatory. It makes case when TSO header is not
fragmented a bit more faster.
Fixes: fec33d5bb3 ("net/sfc: support firmware-assisted TSO")
Cc: stable@dpdk.org
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Phy capabilities are bit offsets in libefx, but was used as bit masks.
Fixes: d23f3a89ab ("net/sfc: support link speed and duplex settings")
Fixes: f82e33afbb ("net/sfc: support link speeds up to 100G")
Cc: stable@dpdk.org
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Rename the macro to make things shorter and more comprehensible. For
both meson and make builds, keep the old macro around for backward
compatibility.
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
The sfc driver was still using RTE_LOGTYPE_PMD which was superseded
by local logging.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Andrew Rybchenko <arybchenko@solarflare.com>
Rather than relying on the target machine architecture, use the
size of a pointer from the compiler to determine if we are 64-bits
or not. This allows correct behaviour when you pass -m32 as a compile
option. It also allows us to use this value repeatedly throughout the
repo rather than continually testing for the sizeof(void*).
Signed-off-by: Bruce Richardson <bruce.richardson@intel.com>
Tested-by: Luca Boccassi <bluca@debian.org>
Acked-by: Luca Boccassi <bluca@debian.org>
Move duplicate macro to increment per-event type stats to
internal header. These stats are NIC family independent and
stored in generic event queue structure.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Include efx_mcdi.h from main internal header efx_impl.h directly
instead of indirect inclusion via family-specific header.
It avoids duplication and fixes Medford and Medford2 cases where
the header inclusion is lost.
Correctness is still guaranteed by checks in efx_check.h which
require EFSYS_OPT_MCDI for corresponding families and do not
allow to enable the option if no family requires it.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
If event queue timers are not supported, enc_evq_timer_quantum_ns and
enc_evq_timer_max_us should be set to 0. Make sure that division by 0
does not happen in libefx, if public function efx_ev_usecs_to_ticks()
is used in this case.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Add EFX_FAMILY_IS_EF10() which may be used as synonym of any EF10-based
NIC family (i.e. Huntigton, Medford or Medford2 at the time of addition).
Suggested-by: Andy Moreton <amoreton@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Add EFX_OPTS_EF10() which may be used as synonym of any EF10-based
NIC (i.e. Huntigton, Medford or Medford2 at the time of addition).
Suggested-by: Andy Moreton <amoreton@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Riverhead requires Rx buffer size to be specified in INIT_RXQ.
If the parameter is not supported (e.g. on EF10 family adapters),
zero must be used on INIT_RXQ.
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Supports the firmware update mechanism described in SF-121352-AN.
Signed-off-by: Richard Houldsworth <rhouldsworth@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The recently added NO_CONT_EV mode is recommended for when looking for
maximum throughput on 100G links as it allows the firmware to operate
more efficiently. The biggest benefit is when using scatter and jumbo
frames, but it is also necessary to achieve line rate in other cases.
Support for NO_CONT_EV when scatter is disabled is simple - the main
datapath change is to always read the packet length from the prefix,
not the event. This requires storing a flag with the event queue so
the event handler knows NO_CONT_EV mode is in use.
Supporting NO_CONT_EV with scatter would require an API change.
(Now the ee_flags field in efx_evq_t is used on the datapath, move it
next to other fields which are also read on the datapath to try to avoid
reading an additional cache line.)
Signed-off-by: Mark Spender <mspender@solarflare.com>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The macros are deprecated and are not used anymore, so they can
be deleted.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Symbols for maximum and minimum number of Tx, Rx and event descriptors
are deprecated. They are not used anymore, so they can be deleted.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Use of the macro for calculating a Rx queue size is deprecated. Replace
it with a call to a function that uses descriptor size specified for
every NIC.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Use of the macro for calculating a Rx queue size is deprecated. Replace
it with a call to a function that uses descriptor size specified for
every NIC.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Use of the macro for calculating a Tx queue size is deprecated. Replace
it with a call to a function that uses descriptor size specified for
every NIC.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Functions efx_*q_nbufs return the number of a queue buffers by dividing
the queue size by page size. If minimum size of a queue is smaller than
one page, we still need the page and number of buffers should not be 0.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
For consistency with the size of Tx descriptors, the size of event
descriptors should be a part of NIC config, not a macro that is
common for all NIC families. Also, add a max number of EvQ buffers
define which is needed to initialize an MCDI buffer at compile time.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
For consistency with the size of Tx descriptors, the size of Rx
descriptors should be a part of NIC config, not a macro that is
common for all NIC families.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Size of Tx descriptor is different on Riverhead. So, the size
should be a part of NIC config, not a macro that is common for
all NIC families.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The change is needed for the functions that accept const efx_nic_t
pointer and have to get efx_nic_cfg_t.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The define EFX_TXQ_MAX_BUFS is used only by EF10 family implementation.
Since the macro is not used by any drivers, it does not require
exposed libefx interface.
Make the define EF10-specific.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
The macro EFX_RXQ_DC_NDESCS() is used only by Siena implementation.
Since the macro is not used by any drivers, it does not require
exposed libefx interface.
Make the macro Siena-specific.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Now we have min/max limits in NIC config, so we can do check against
min/max in a generic place instead of NIC family specific functions.
Check that the descriptors number is a power of 2 is also can be
made common. It removes code duplication and makes NIC family
specific functions a bit shorter.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Now we have min/max limits in NIC config, so we can do check against
min/max in a generic place instead of NIC family specific functions.
Check that the descriptors number is a power of 2 is also can be
made common. It removes code duplication and makes NIC family
specific functions a bit shorter.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Now we have min/max limits in NIC config, so we can do check against
min/max in a generic place instead of NIC family specific functions.
Check that the descriptors number is a power of 2 is also can be made
common. It removes code duplication and makes NIC family
specific functions a bit shorter.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Descriptor limits are not common for all NIC families. Use the variables
from NIC configuration instead of deprecated defines.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Descriptor limits are not common for all NIC families. Use the variables
from NIC configuration instead of deprecated defines.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
Min limit is not common for all NIC families. Use the variable from
NIC configuration instead of deprecated define.
Signed-off-by: Igor Romanov <igor.romanov@oktetlabs.ru>
Signed-off-by: Andrew Rybchenko <arybchenko@solarflare.com>
