This patch adds support to
1) enable VF MAC anti spoof.
2) QOS configuration for specified VF.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add functions rte_pmd_bnxt_set_tx_loopback,
rte_pmd_bnxt_set_all_queues_drop_en and
rte_pmd_bnxt_set_vf_mac_addr to configure tx_loopback,
queue_drop and VF MAC address setting in the hardware.
It also adds the necessary functions to send the HWRM commands
to the firmware.
Signed-off-by: Steeven Li <steeven.li@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1) Use hwrm_stat_ctx_query command to query statistics
Using hwrm_stat_ctx_query command will allow polling
the statistics from hardware instead of using the current push
model from the hardware which does a DMA of the stats to the host
at fixed intervals.
2) Use the rx_mbuf_alloc_fail to track mbuf alloc failures.
3) We were wrongly incrementing hwrm_cmd_seq in bnxt_hwrm_stat_clear
and bnxt_hwrm_stat_ctx_alloc functions. This patch fixes that.
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to modify MTU using the set_mtu dev_op.
To support frames > 2k, the PMD creates an aggregator ring.
When a frame greater than 2k is received, it is fragmented
and the resulting fragments are DMA'ed to the aggregator ring.
Now the driver can support jumbo frames upto 9500 bytes.
Signed-off-by: Steeven Li <steeven.li@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to get and reset xstats dev_ops
dev_ops added:
xstats_get, xstats_get_name, xstats_reset
HWRM commands added:
hwrm_port_qstats, hwrm_port_clr_stats
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Add support for udp_tunnel_port_add/del dev_ops to configure a UDP port
for VXLAN and Geneve Tunnel protocols.
The HWRM supports only one global destination port for a tunnel type,
use a reference counter to keep track of its usage.
Cache the configured VXLAN/Geneve ports and use that value to check
if the right UDP port is being freed up.
Skip calling bnxt_hwrm_tunnel_dst_port_alloc if the same UDP port is
being programmed.
Skip calling bnxt_hwrm_tunnel_dst_port_free if no UDP port has been
configured.
Also update tx offload capabilities
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
1) Move the function reset to bnxt_dev_init.
On the same lines, setup, enable and request interrupt to init path.
Memory allocation is also being done in the init path.
2) After a function reset, configure the VFs. Distribute resources
evenly between all functions (PF and VF) for now. In the future, this
should be controllable.
3) The bnxt_vf_info and bnxt_pf_info had lot of duplication. Move the
common items to struct bnxt. And only unique items specific to PF
remain in the struct bnxt_pf_info.
4) Program the firmware to allow certain commands sent by a VF.
Disallowing these will prevent clean VF driver cleanup.
5) Since PF/VF need to allocate resources from a pool in the hardware,
use func_qcaps and func_qcfg to appropriately query the capabilities
and available resources.
6) If a PF is being initialized and no VFs are allocated, explicitly
call func_cfg to allocate the resources.
7) Once resources are requested from the firmware, update local copy
of resource count in struct bnxt only after sending the func_qcfg to
make sure the allocation request in the firmware went through.
The changes in this patch will be used by the subsequent patches
to allow proper initialization of PF/VF instance.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch adds support to get Link notification asynchronously.
The HW sends async notifications on default completion ring. The
PMD processes these notifications and logs a message appropriately.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
This patch fixes segfault encountered during dev_uninit/close routine.
KNI sample app can be used to reproduce the issue.
Fixes: c09f57b49c ("net/bnxt: add start/stop/link update operations")
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Adding code to enable support for NIC Partitioning or NPAR 1.0
As a part of NPAR, we don't allow port settings like speed or flow
control to be changed.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
This requires a group info array in struct bnxt, so add that, we can save
the max size from the func_qcap response, and alloc/free in init/uninit
New HWRM call:
bnxt_hwrm_vnic_alloc:
Allocates a VNIC resource in the hardware.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
In this patch we are adding the bnxt_rx_queue_setup_op() and
bnxt_rx_queue_release_op() functions. These will be tied to the
rx_queue_setup and rx_queue_release dev_ops in a subsequent patch.
In these functions we allocate/free memory for the RX queues.
This still requires support to create a RX ring in the ASIC which
will be completed in a future commit. Each Rx queue created via the
rx_queue_setup dev_op will have an associated Rx ring in the hardware.
The Rx logic in the hardware picks a Rx ring for each Rx frame received
by the hardware depending on the properties like RSS, MAC and VLAN
settings configured in the hardware. These packets in the end arrive
on the Rx queue corresponding to the Rx ring in the hardware.
We are also adding some functions like bnxt_mq_rx_configure()
bnxt_free_rx_mbufs() and bnxt_free_rxq_stats() which will be used in
subsequent patches.
We are also adding hwrm_vnic_rss_cfg_* structures, which will be used
in subsequent patches to enable RSS configuration.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add the L2 filter structure and the alloc/init/free functions for
dealing with them.
A filter is used to identify traffic that contains a matching set of
parameters like unicast or broadcast MAC address or a VLAN tag amongst
other things which then allows the ASIC to direct the incoming traffic
to an appropriate VNIC or Rx ring.
New HWRM calls:
bnxt_hwrm_clear_filter:
Free a L2 filter.
bnxt_hwrm_set_filter
Allocate an An L2 filter or a L2 context.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Structures, macros, and functions for working with completion rings
in the driver.
Completion Ring is used by the Ethernet controller to provide the
status of transmitted & received packets, report errors, report
status changes to the host software, and inter-function forwarding
requests. In addition to the generic ring features, a completion ring
can have a statistics context that has statistics periodically DMAed
to host memory, along with a consumer index.
bnxt_handle_async_event() handles completions not related to a specific
transmit or receive ring such as link status changes which arrive on
the default completion ring.
Other physical or virtual functions on the same device may send an HWRM
command forward request. In this case, we will pass it through
unvalidated. In the future, we will be able to have the PF monitor and
control VF access to the HWRM interface if needed.
New HWRM Calls:
bnxt_hwrm_exec_fwd_resp:
Execute an encapsulated command and forward the response.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Add functions to allocate, initialize, and free vnics.
A VNIC represents a virtual interface. It is a resource in the RX path
of the chip and is used to setup various target actions such as RSS,
MAC filtering etc. for the physical function in use.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
The dev_configure_op function calls bnxt_set_hwrm_link_config() to
setup the PHY. This calls the new bnxt_parse_eth_link_*() functions
to translate from the DPDK macro values to those used by HWRM calls,
then calls bnxt_hwrm_port_phy_cfg() to issue the HWRM call.
New HWRM calls:
bnxt_hwrm_port_phy_cfg:
This command configures the PHY device for the port.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Gets device info from the bp structure filled in the init() function.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Move init() cleanup into uninit() function
Fix .dev_private_size
New HWRM calls:
bnxt_hwrm_func_driver_register:
This command is used by the function driver to register
its information with the HWRM.
bnxt_hwrm_func_driver_unregister:
This command is used by the function driver to unregister
with the HWRM.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
Start adding support to use the HWRM API.
Hardware Resource Manager or HWRM in short, is a set of API provided
by the firmware running in the ASIC to manage the various resources.
Initial commit just performs necessary HWRM queries for init, then
fails as before.
Now that struct bnxt is non-zero size, we can set dev_private_size
correctly.
The used HWRM calls so far:
bnxt_hwrm_func_qcaps:
This command returns capabilities of a function.
bnxt_hwrm_ver_get:
This function is called by a driver to determine the HWRM
interface version supported by the HWRM firmware, the
version of HWRM firmware implementation, the name of HWRM
firmware, the versions of other embedded firmwares, and
the names of other embedded firmwares, etc. Gets the
firmware version and interface specifications. Returns
an error if the firmware on the device is not supported
by the driver and ensures the response space is large
enough for the largest possible response.
bnxt_hwrm_queue_qportcfg:
This function is called by a driver to query queue
configuration of a port.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Stephen Hurd <stephen.hurd@broadcom.com>
Reviewed-by: David Christensen <david.christensen@broadcom.com>
