numam-spdk/doc/nvmf.md

NVMe over Fabrics Target

@sa @ref nvme_fabrics_host

NVMe-oF Target Getting Started Guide

The NVMe over Fabrics target is a user space application that presents block devices over the network using RDMA. It requires an RDMA-capable NIC with its corresponding OFED software package installed to run. The target should work on all flavors of RDMA, but it is currently tested against Mellanox NICs (RoCEv2) and Chelsio NICs (iWARP).

The NVMe over Fabrics specification defines subsystems that can be exported over the network. SPDK has chosen to call the software that exports these subsystems a "target", which is the term used for iSCSI. The specification refers to the "client" that connects to the target as a "host". Many people will also refer to the host as an "initiator", which is the equivalent thing in iSCSI parlance. SPDK will try to stick to the terms "target" and "host" to match the specification.

There will be both a target and a host implemented in the Linux kernel, and these are available today as a set of patches against the kernel 4.8 release candidate. All of the testing against th SPDK target has been against the proposed Linux kernel host. This means that for at least the host machine, the kernel will need to be a release candidate until the code is actually merged. For the system running the SPDK target, however, you can run any modern flavor of Linux as required by your NIC vendor's OFED distribution.

If you want to kill the application using signal, make sure use the SIGTERM, then the application will release all the share memory resource before exit, the SIGKILL will make the share memory resource have no chance to be released by application, you may need to release the resource manually.

Prerequisites

This guide starts by assuming that you can already build the standard SPDK distribution on your platform. By default, the NVMe over Fabrics target is not built. To build nvmf_tgt there are some additional dependencies.

Fedora:

dnf install libibverbs-devel librdmacm-devel

Ubuntu:

apt-get install libibverbs-dev librdmacm-dev

Then build SPDK with RDMA enabled, either by editing CONFIG to enable CONFIG_RDMA or enabling it on the make command line:

make CONFIG_RDMA=y <other config parameters>

Once built, the binary will be in app/nvmf_tgt.

Prerequisites for InfiniBand/RDMA Verbs

Before starting our NVMe-oF target we must load the InfiniBand and RDMA modules that allow userspace processes to use InfiniBand/RDMA verbs directly.

modprobe ib_cm
modprobe ib_core
modprobe ib_ucm
modprobe ib_umad
modprobe ib_uverbs
modprobe iw_cm
modprobe rdma_cm
modprobe rdma_ucm

Prerequisites for RDMA NICs

Before starting our NVMe-oF target we must detect RDMA NICs and assign them IP addresses.

Mellanox ConnectX-3 RDMA NICs

modprobe mlx4_core
modprobe mlx4_ib
modprobe mlx4_en

Mellanox ConnectX-4 RDMA NICs

modprobe mlx5_core
modprobe mlx5_ib

Assigning IP addresses to RDMA NICs

ifconfig eth1 192.168.100.8 netmask 255.255.255.0 up
ifconfig eth2 192.168.100.9 netmask 255.255.255.0 up

Configuring NVMe over Fabrics Target

A nvmf_tgt-specific configuration file is used to configure the NVMe over Fabrics target. This file's primary purpose is to define subsystems. A fully documented example configuration file is located at etc/spdk/nvmf.conf.in.

You should make a copy of the example configuration file, modify it to suit your environment, and then run the nvmf_tgt application and pass it the configuration file using the -c option. Right now, the target requires elevated privileges (root) to run.

app/nvmf_tgt/nvmf_tgt -c /path/to/nvmf.conf

Configuring NVMe over Fabrics Host

Both the Linux kernel and SPDK implemented NVMe over Fabrics host. Users who want to test nvmf_tgt with kernel based host should upgrade to Linux kernel 4.8 or later, or can use Linux distributions Fedora or Ubuntu with Linux 4.8 kernel or later. A client tool nvme-cli is recommended to connect/disconect with NVMe over Fabrics target subsystems. Before connecting to remote subsystems, users should verify nvme-rdma driver is loaded.

Discovery:

nvme discover -t rdma -a 192.168.100.8 -s 4420

Connect:

nvme connect -t rdma -n "nqn.2016-06.io.spdk:cnode1" -a 192.168.100.8 -s 4420

Disconnect:

nvme disconnect -n "nqn.2016-06.io.spdk:cnode1"

Assigning CPU Cores to the NVMe over Fabrics Target

SPDK uses the DPDK Environment Abstraction Layer to gain access to hardware resources such as huge memory pages and CPU core(s). DPDK EAL provides functions to assign threads to specific cores. To ensure the SPDK NVMe-oF target has the best performance, configure the RNICs and NVMe devices to be located on the same NUMA node. The following parameters in the configuration file are used to configure SPDK NVMe-oF target:

ReactorMask: A hexadecimal bit mask of the CPU cores that SPDK is allowed to execute work items on. The ReactorMask is located in the [Global] section of the configuration file. For example, to assign lcores 24,25,26 and 27 to NVMe-oF work items, set the ReactorMask to:

ReactorMask 0xF000000

Subsystem configuration: the [Subsystem] section in the configuration file is used to configure subysystems for the NVMe-oF target.

[Nvme]
TransportID "trtype:PCIe traddr:0000:02:00.0" Nvme0
TransportID "trtype:PCIe traddr:0000:82:00.0" Nvme1

[Subsystem1]
NQN nqn.2016-06.io.spdk:cnode1
Listen RDMA 192.168.100.8:4420
AllowAnyHost No
Host nqn.2016-06.io.spdk:init
SN SPDK00000000000001
Namespace Nvme0n1 1

[Subsystem2]
NQN nqn.2016-06.io.spdk:cnode2
Listen RDMA 192.168.100.9:4420
AllowAnyHost Yes
SN SPDK00000000000002
Namespace Nvme1n1 1

SPDK spreads the execution of requests for a single subsystem across all available cores in a round-robin manner.

Emulating an NVMe controller

The SPDK NVMe-oF target provides the capability to emulate an NVMe controller using a virtual controller. Using virtual controllers allows storage software developers to run the NVMe-oF target on a system that does not have NVMe devices. You can configure a virtual controller in the configuration file as follows:

Create malloc LUNs: See @ref bdev_getting_started for details on creating Malloc block devices.

Create a virtual controller: Any bdev may be presented as a namespace. For example, to create a virtual controller with two namespaces backed by the malloc LUNs named Malloc0 and Malloc1 and made available as NSID 1 and 2:

# Virtual controller
[Subsystem2]
  NQN nqn.2016-06.io.spdk:cnode2
  Listen RDMA 192.168.2.21:4420
  AllowAnyHost No
  Host nqn.2016-06.io.spdk:init
  SN SPDK00000000000001
  Namespace Malloc0 1
  Namespace Malloc1 2