numam-spdk/doc/vhost_processing.md

Vhost processing

Table of Contents

• @ref vhost_processing_intro
• @ref vhost_processing_qemu
• @ref vhost_processing_init
• @ref vhost_processing_io_path

Introduction

This document is intended to provide an overall high level insight into how Vhost works behind the scenes. It assumes you're already familiar with the basics of virtqueues and vrings from the VIRTIO protocol. Code snippets used in this document might have been simplified for the sake of readability and should not be used as an API or implementation reference.

vhost is a protocol for devices accessible via inter-process communication. It uses the same virtqueue and vring layout for I/O transport as VIRTIO to allow direct mapping to Virtio devices. The initial vhost implementation is a part of the Linux kernel and uses ioctl interface to communicate with userspace applications. What makes it possible for SPDK to expose a vhost device is Vhost-user protocol.

The Vhost-user specification describes the protocol as follows:

[Vhost-user protocol] is aiming to complement the ioctl interface used to
control the vhost implementation in the Linux kernel. It implements the control
plane needed to establish virtqueue sharing with a user space process on the
same host. It uses communication over a Unix domain socket to share file
descriptors in the ancillary data of the message.

The protocol defines 2 sides of the communication, master and slave. Master is
the application that shares its virtqueues, in our case QEMU. Slave is the
consumer of the virtqueues.

In the current implementation QEMU is the Master, and the Slave is intended to
be a software Ethernet switch running in user space, such as Snabbswitch.

Master and slave can be either a client (i.e. connecting) or server (listening)
in the socket communication.

SPDK vhost is a Vhost-user slave server. It exposes Unix domain sockets and allows external applications to connect.

QEMU

One of major Vhost-user use cases is networking (DPDK) or storage (SPDK) offload in QEMU. The following diagram presents how QEMU-based VM communicates with SPDK Vhost-SCSI device.

The irqfd mechanism isn't described in this document, as it KVM/QEMU-specific. Briefly speaking, doing an eventfd_write on the callfd descriptor will directly interrupt the guest because of irqfd.

Device initialization

All initialization and management information is exchanged via the Vhost-user messages. The connection always starts with the feature negotiation. Both the Master and the Slave exposes a list of their implemented features. Most of these features are implementation-related, but also regard e.g. multiqueue support or live migration. A feature will be used only if both sides support it.

After the negotiatiation Vhost-user driver shares its memory, so that the vhost device (SPDK) can access it directly. The memory can be fragmented into multiple physically-discontiguous regions, although Vhost-user specification enforces a limit on their number (currently 8). The driver sends a single message with the following data for each region:

• file descriptor - for mmap
• user address - for memory translations in Vhost-user messages (e.g. translating vring addresses)
• guest address - for buffers addresses translations in vrings (for QEMU this is a physical address inside the guest)
• user offset - positive offset for the mmap
• size

The Master will send new memory regions after each memory change - usually hotplug/hotremove. The previous mappings will be removed.

Drivers may also request a device config, consisting of e.g. disk geometry. Vhost-SCSI drivers, however, don't need implement this functionality as they use common SCSI I/O to inquiry the underlying disk(s).

Afterwards, the driver requests the number of maximum supported queues and starts sending virtqueue data, which consists of:

• unique virtqueue id
• index of the last processed vring descriptor
• vring addresses (from user address space)
• call descriptor (for interrupting the driver after I/O completions)
• kick descriptor (to listen for I/O requests - unused by SPDK)

If multiqueue feature has been negotiated, the driver has to send a specific ENABLE message for each extra queue it wants to be polled. Other queues are polled as soon as they're initialized.

I/O path

The Master sends I/O by allocating proper buffers in shared memory, filling the request data, and putting guest addresses of those buffers into virtqueues.

A Virtio-Block request looks as follows.

struct virtio_blk_req {
        uint32_t type; // READ, WRITE, FLUSH (read-only)
        uint64_t offset; // offset in the disk (read-only)
        struct iovec buffers[]; // scatter-gatter list (read/write)
        uint8_t status; // I/O completion status (write-only)
};

And a Virtio-SCSI request as follows.

struct virtio_scsi_req_cmd {
  struct virtio_scsi_cmd_req *req; // request data (read-only)
  struct iovec read_only_buffers[]; // scatter-gatter list for WRITE I/Os
  struct virtio_scsi_cmd_resp *resp; // response data (write-only)
  struct iovec write_only_buffers[]; // scatter-gatter list for READ I/Os
}

Virtqueue generally consists of an array of descriptors and each I/O needs to be converted into a chain of such descriptors. A descriptor can be either readable or writable, so each I/O request must consist of at least two descriptors (request + response).

struct virtq_desc {
        /* Address (guest-physical). */
        le64 addr;
        /* Length. */
        le32 len;

/* This marks a buffer as continuing via the next field. */
#define VIRTQ_DESC_F_NEXT   1
/* This marks a buffer as device write-only (otherwise device read-only). */
#define VIRTQ_DESC_F_WRITE     2
        /* The flags as indicated above. */
        le16 flags;
        /* Next field if flags & NEXT */
        le16 next;
};

The device after polling this descriptor chain needs to translate and transform it back into the original request struct. It needs to know the request layout up-front, so each device backend (Vhost-Block/SCSI) has its own implementation for polling virtqueues. For each descriptor, the device performs a lookup in the Vhost-user memory region table and goes through a gpa_to_vva translation (guest physical address to vhost virtual address). SPDK enforces the request and response data to be contained within a single memory region. I/O buffers do not have such limitations and SPDK may automatically perform additional iovec splitting and gpa_to_vva translations if required. After forming request structs, SPDK forwards such I/O to the underlying drive and polls for the completion. Once I/O completes, SPDK vhost fills the response buffer with proper data and interrupts the guest by doing an eventfd_write on the call descriptor for proper virtqueue. There are multiple interrupt coalescing features involved, but they won't be discussed in this document.