be compiled. Old tty ioctls are still used (possibly ifdef'ed) in at
least the following programs in the src tree:
atc des ee fontedit gdb gdbserver lock ntp perl5 tcsh telnet top vttest
rp.c:
Unremoved used variables so that the support for old ioctls actually
compiles.
Not tested at runtime by: bde
ACPI_NO_SEMAPHORES, ASR_MEASURE_PERFORMANCE, AST_DEBUG, ATAPI_DEBUG,
ATA_DEBUG, BKTR_ALLOC_PAGES, BROOKTREE_ALLOC_PAGES, CAPABILITIES,
COMPAT_SUNOS, CV_DEBUG, MAXFILES, METEOR_TEST_VIDEO, NDEVFSINO,
NDEVFSOVERFLOW, NETGRAPH_BRIDGE, NETSMB, NETSMBCRYPTO, PFIL_HOOKS,
SIMOS, SMBFS, VESA_DEBUG, VGA_DEBUG.
Start using #! to comment out negative options and ## to comment out
broken options.
atapi-all.c:
Fixed rotted bits that were hiding under ATAPI_DEBUG.
atapi-cd.c:
#include "opt_ata.h" so that ACD_DEBUG is actually visible.
ata/atapi-tape.c
#include "opt_ata.h" so that AST_DEBUG is actually visible.
In order of importance:
+ each cluster now uses private data structures (filtering and
local address tables) so you can treat them as fully independent
switches. This part of the work was supported by:
Cisco Systems, Inc. - NSITE lab, RTP, NC.
+ cleaned up the handling of configuration, so the system will behave
much better when real or pseudo devices are dynamically attached
or detached. It should also not panic anymore on systems with large
number of devices, closing a few existings PRs on the topic.
+ while at it, add support for VLAN. This means that a FreeBSD box
can now work as a real VLAN switch, with trunk interfaces etc.
As an example:
ifconfig vlan0 vlan 3 vlandev dc0
ifconfig vlan1 vlan 4 vlandev dc0
net.link.ether.bridge_cfg="vlan0:3,dc1:3,vlan1:4,dc1:4"
uses dc0 as a trunk interface, and dc1 and dc3 as ports on vlans 3 and 4
You get the idea...
NOTA BENE: by default bridge_cfg is initialised to "" so even if
you enable bridging, no packets will be bridged until you set the
list of interfaces on which you want this to happen.
+ large restructuring of the code, moving private vars and types from
bridge.h to bridge.c.
+ added a lot of comments to the code to explain how to use it.
This escaped because DEVICE_POLLING is disabled in LINT being
not compatible with SMP. In fact, it is only a runtime problem,
so if we could recognize that we are building a LINT kernel
we could as well disable the check for SMP being defined.
Reported-by: Joe Clarke
- missing whitespace
- strange version of warn() built out of warnx() + strerror(). Just use
warn().
- conversion of just one of the two perror()'s to warn*()
Actually use _warn() instead of _warn(), to keep up with namespace-
unpollution for warn().
and disable telnet and friends in favour of ssh/sshd/scp.
Pull out a few NIC drivers from the config file to make the
image fit into a 1.44 image again. I have left "lnc" in as that is
emulated by vmware so this can be booted there.
Finish it by adding kerberos5/lib/libvers to the build-tools list.
(I didn't notice it before because I tested my fix in a -DNOCLEAN
environment, and static libc.a was already in ${WORLDTMP}/usr/lib,
and libvers's make-print-version build tool used it for linking.)
Spotted by: John Indra <maverick@office.naver.co.id>
Move group_from_gid to grp.h
Remove from stdlib.h
Make the prototypes match the code
Fix rm and mv to include new files.
NetBSD has these defined in those files, and others too that I've not
done.
Approved by: terminal room kabal
Reviewed by: jhb, phk
boot sequence.
The new pmap.c is based on NetBSD's newer pmap.c (for the mpc6xx processors)
which is 70% faster than the older code that the original pmap.c was based
on. It has also been based on the framework established by jake's initial
sparc64 pmap.c.
There is no change to how far the kernel gets (it makes it to the mountroot
prompt in psim) but the new pmap code is a lot cleaner.
Obtained from: NetBSD (pmap code)
volumes are available, instead of getting stuck in a loop calling
getvol(). Normally restore in 'x' or 'i' modes will ask for a new
(earlier) volume when the current inode number on the tape is greater
than the last inode to be restored, since there can be no further
inodes of interest on that volume. However we don't want to change
volumes in this case either if the user explicitly said that there
are no more tapes, or if we are looking at the first volume.
When no more volumes are available but there are still inodes that
we have not found, we now just fall through to the code that prints
out a list of any missing files, so the restore completes normally.
Also simplify the logic a bit by always returning to the start of
the main for(;;) loop whenever the volume has changed.
This should completely fix the "Changing volumes on pipe input" bug
that is often observed when restoring dumps of active filesystems.
PR: bin/4176, bin/34604, misc/34675
break scheduling because negative priorities were most fixed up by
converting kg_pri_user back to the correct type.
Fixed some style bugs in previous commit (non-terminated sentence fragments
and regressions in comments).
SMP we'd like as much feedback as possible from users about possible
locking problems as early as possible.
To negate most of the performance impact I've also enabled
WITNESS_SKIPSPIN. I've done this as we've been running WITNESS
over the spinlock code for a while without incident and it goes a
long way to making the performance problems of WITNESS much more
bearable.
Users who should be running current should know about turning WITNESS
off for performance reasons.
That said and done, WITNESS could/should be made into a tuneable,
but we'll leave that as an excersize to those that want to disable
it without a kernel recompile.
descriptors. This simplifies code for jumbo frames.
- Cleaned up coding conventions to make code more unix-like.
- Cleaned up code in if_em_fxhw.c and if_em_phy.c.
Added relevant comments.
MFC after: 1 week
support for managing both streaming caches on psycho pairs).
Use explicit bus space accesses instead of mapping the device memory into
kva.
Move DVMA allocation to the map creation/dma memory allocation functions.
