adds probes for mutexes, reader/writer and shared/exclusive locks to
gather contention statistics and other locking information for
dtrace scripts, the lockstat(1M) command and other potential
consumers.
Reviewed by: attilio jhb jb
Approved by: gnn (mentor)
request to arrive. Previously it would end up returning as soon as the
request length stored in the first two bytes had arrived.
Reviewed by: dwmalone
MFC after: 1 week
about removing a few #ifdefs and providing compatibility wrappers and
VOP implementations to get and set an ACL; ZFS does ACL enforcement all
by itself.
Note that the VOPs are ifdefed out for now, so this change should be
a no-op.
Reviewed by: pjd
that the range of versions of NFS handled by the server can
be limited. The nfsd daemon must be restarted after these
sysctl variables are changed, in order for the change to take
effect.
Approved by: kib (mentor)
that it handles the case of a non-exported NFSv4 root correctly.
Also, delete handling for the case where nd_repstat is already
set in nfs_proc(), since that no longer happens.
Approved by: kib (mentor)
o do not attach DLT_IEEE802_11_RADIO unless both tx and rx headers are
present; this is assumed in the capture code paths
o verify the above with asserts in ieee80211_radiotap_{rx,tx}
o add missing checks for active taps before calling ieee80211_radiotap_rx
PCB, simply embed it in the PCB, avoiding additional memory overhead,
memory allocation overhead, and removing one of the few remaining
uses of dtom() in the network stack.
Restore misplaced spx_ctlinput() from an earlier commit.
MFC after: 1 month
severe silicon bugs that can't handle VLAN hardware tagging as well
as status LE writeback bug. The status LE writeback bug is so
critical we can't trust status word of received frame. To accept
frames on Yukon FE+ A0 msk(4) just do minimal check for received
frames and pass them to upper stack. This means msk(4) can pass
corrupted frames to upper layer. You have been warned!
Also I supposed RX_GMF_FL_THR to be 32bits register but Linux
driver treated it as 16bit register so follow their leads. At least
this does not seem to break msk(4) on Yukon FE+.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
Yukon FE+ is fast ethernet controller and uses new descriptor
format. Since I don't have this controller, the support code was
written from guess and various feedback from enthusiastic users.
Thanks to all users who patiently tested my initial patches.
Special thanks to Tanguy Bouzeloc who fixed critical bug of initial
patch.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
The GM_GP_CTRL register may have stale content from previous link
information so clearing it will make hardware update the register
correctly when it established a valid link.
While I'm here remove stale comment.
does not guarantee established link. Also 1000baseT link report for
fast ethernet controller is not valid one so make sure gigabit link
is allowed for this controller.
Whenever we lost link, check whether Rx/Tx MACs were enabled. If both
MAC are not active, do not try to disable it again.
mark controller's capability. Controllers that have jumbo frame
support sets MSK_FLAG_JUMBO, and controllers that does not support
checksum offloading for jumbo frames will set MSK_FLAG_JUMBO_NOCSUM.
For Fast Ethernet controllers it will set MSK_FLAG_FASTETHER and it
would be used in link state handling.
While here, disable Tx checksum offloading if jumbo frame is used
on controllers that does not have Tx checksum offloading capability
for jumbo frame(e.g. Yukon EC Ultra).
FE+ controller. Due to the severe silicon bugs for Yukon FE+,
88E3016 seems to require more workarounds. However I'm not sure
whether the workaround is PHY specific or only applicable to Yukon
FE+. The datasheet for the PHY is publicly available but it lacks
several details for the workaround used in this change. The
workaround information was obtained from Linux. Many thanks to
Yukon FE+ users who helped me add 88E3016 support.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
advertisement register. Some PHYs such as 88E3016 requires NEXT
Page capability to establish valid link. Also set protocol selector
field which is read only but it makes the intention clearer.
is valid only for auto-negotiation case so check the bit if we know
auto-negotiation is active. While I'm here explicitly checks
current speed with speed mask and set IFM_NONE if resolved speed
is unknown.
checks extended status register to see whether the PHY is fast
ethernet or not. This removes a lot of checks for specific PHY
models and it makes easy to add more PHYs to e1000phy(4).
While I'm here remove setting mii_anegticks as it is set with
mii_phy_add_media().
ReleaseLockOwner operations analagous to what is already
in place for SetClientID and SetClientIDConfirm. These are
the five NFSv4 operations that do not use file handle(s),
so the checks are done using the NFSv4 root export entries
in /etc/exports.
Approved by: kib (mentor)
Remove PAGE_SIZE alignment used in Rx buffer DMA tag creation. The
alignment restriction was used in old local jumbo allocator and
nfe(4) switched to UMA backed page allocator for jumbo frame.
This change should fix jumbo buffer allocation failure.
Reported by: Pascal Braun ( pascal.braun <> continum dot net )
to it for the client side reply. Hopefully this fixes the
problem with using the new krpc for arm for the experimental
nfs client.
Approved by: kib (mentor)
where a client is not allowed NFSv4 access correctly. This
restriction is specified in the "V4: ..." line(s) in
/etc/exports.
Approved by: kib (mentor)
on platforms with strict alignment requirements. In particular, this fixes the
problems with the new RPC transport on the arm platform.
Note: this adds yet another copy of nfs_realign(). I will attempt to refactor
after NFS_LEGACYRPC is removed.
Submitted by: sam
sleep waiting for conditions when the lock may be granted.
To prevent lf_setlock() from accessing possibly freed memory, add reference
counting to the struct lockf_entry. Bump refcount around the sleep.
Make lf_free_lock() return non-zero when structure was freed, and use
this after the sleep to return EINTR to the caller. The error code might
need a clarification, but we cannot return success to usermode, since
the lock is not owned anymore.
Reviewed by: dfr
Tested by: pho
MFC after: 1 month
is acquired. In the lf_purgelocks(), assert that vnode is doomed and set
*statep to NULL before clearing ls_pending list. Otherwise, we allow for
the thread executing lf_advlockasync() to put new pending entry after
state->ls_lock is dropped in lf_purgelocks().
Reviewed by: dfr
Tested by: pho
MFC after: 1 month
In the original MPSAFE TTY code, I changed the behaviour by returning
EBUSY. I thought this made more sense, because it's basically a race to
see who gets the TTY first.
It turns out this is not a good change, because it also causes EBUSY to
be returned when another process is closing the TTY. This can happen
during startup, when /etc/rc (or one of its children) is still busy
draining its data and /sbin/init is attempting to open the TTY to spawn
a getty.
Reported by: bz
Tested by: bz
case of a kerberized mount without a host based principal
name. This will only work for mounts being done by a user
other than root. Support for a host based principal name
will not work until proposed changes to the rpcsec_gss part
of the krpc are committed. It now builds for "options KGSSAPI".
Approved by: kib (mentor)
vimage options along with all the defines made things really hard to
read and get right; thus add comments for the #else/#endif cases.
Discussed with: zec
to optionally have overlapping unit numbers if attached in different
vnets.
At this stage if_loop is the only clonable ifnet class that has been
extended to allow for such overlapping allocation of unit numbers, i.e.
in each vnet it is possible to have a lo0 interface. Other clonable ifnet
classes remain to operate with traditional semantics, i.e. each instance
of a clonable ifnet will be assigned a globally unique unit number,
regardless in which vnet such an ifnet becomes instantiated.
While here, garbage collect unused _lo_list field in struct vnet_net,
as well as improve indentation for #defines in sys/net/vnet.h.
The layout of struct vnet_net has changed, therefore bump
__FreeBSD_version.
This change has no functional impact on nooptions VIMAGE kernel builds.
Reviewed by: bz, brooks
Approved by: julian (mentor)
be named "udp_inpcb" to avoid a naming conflict with tcp[1].
For consistency rename the uma zone for TCP from "inpcb" to "tcp_inpcb".
Found by: rwatson [1]
Discussed with: rwatson
So far the udp_tun_func_t had been (ab)using inp_ppcb for udp in kernel
tunneling callbacks. Move that into the udpcb and add a field for flags
there to be used by upcoming changes instead of sticking udp only flags
into in_pcb flags2.
Bump __FreeBSD_version for ports to detect it and because of vnet* struct
size changes.
Submitted by: jhb (7.x version)
Reviewed by: rwatson
kernel option.
This also permits tuning of the option per virtual network stack, as
well as separately per inet, inet6.
The kernel option is left for a transition period, marked deprecated,
and will be removed soon.
Initially requested by: phk (1 year 1 day ago)
MFC after: 4 weeks
Cryptodev uses UIO structure do get data from userspace and pass it to
cryptographic engines. Initially UIO size is equal to size of data passed to
engine, but if UIO is prepared for hash calculation an additional small space
is created to hold result of operation.
While creating space for the result, UIO I/O vector size is correctly
extended, but uio_resid field in UIO structure is not modified.
As bus_dma code uses uio_resid field to determine size of UIO DMA mapping,
resulting mapping hasn't correct size. This leads to a crash if all the
following conditions are met:
1. Hardware cryptographic accelerator writes result of hash operation
using DMA.
2. Size of input data is less or equal than (n * PAGE_SIZE),
3. Size of input data plus size of hash result is grather than
(n * PAGE_SIZE, where n is the same as in point 2.
This patch fixes this problem by adding size of the extenstion to uio_resid
field in UIO structure.
Submitted by: Piotr Ziecik kosmo ! semihalf dot com
Reviewed by: philip
Obtained from: Semihalf
write fault or while wiring a mapping that must support write access.
In general, this change should reduce the number of traps that occur for
the purpose of setting the modified bit. More specifically, this change
should prevent traps while holding locks in a sysctl handler. See
kern/kern_sysctl.c revisions 1.168 and 1.195 (svn r192160) for further
details.
Tested by: gonzo
the code will build when "options KGSSAPI" is specified
without requiring the proposed changes that add host based
initiator principal support. It will not handle the case where
the client uses a host based initiator principal until those
changes are committed. The code that uses those changes is
#ifdef'd notyet until the krpc rpcsec_changes are committed.
Approved by: kib (mentor)
because struct vnet_net holds the rt_tables[][] for MRT and array size
is compile time dependent. If you had ROUTETABLES set to >1 after
r192011 V_loif was pointing into nonsense leading to strange results
or even panics for some people.
Reviewed by: mz
for reassigning ifnets from one vnet to another.
if_vmove() works by calling a restricted subset of actions normally
executed by if_detach() on an ifnet in the current vnet, and then
switches to the target vnet and executes an appropriate subset of
if_attach() actions there.
if_attach() and if_detach() have become wrapper functions around
if_attach_internal() and if_detach_internal(), where the later
variants have an additional argument, a flag indicating whether a
full attach or detach sequence is to be executed, or only a
restricted subset suitable for moving an ifnet from one vnet to
another. Hence, if_vmove() will not call if_detach() and if_attach()
directly, but will call the if_detach_internal() and
if_attach_internal() variants instead, with the vmove flag set.
While here, staticize ifnet_setbyindex() since it is not referenced
from outside of sys/net/if.c.
Also rename ifccnt field in struct vimage to ifcnt, and do some minor
whitespace garbage collection where appropriate.
This change should have no functional impact on nooptions VIMAGE kernel
builds.
Reviewed by: bz, rwatson, brooks?
Approved by: julian (mentor)
use the newer nmount() style arguments, as is used by mount_nfs.c.
This prepares the kernel code for the use of a mount_nfs.c with
changes for the experimental client integrated into it.
Approved by: kib (mentor)
only if prepping the adapter failed.
Slight adjustment to comments.
Fix a bug whereby downing the interface didn't preven it from
processing packets.
Submitted by: Navdeep Parhar
MFC after: 1 week
writes upon close when a write delegation is held by the client.
This should be safe to do, now that nfsv4 Close operations are
delayed until ncl_inactive() is called for the vnode.
Approved by: kib (mentor)
- controller reset/firmware loading.
- controller level tracing and tracing of capi messages of applications
running with different user credentials.
Reviewed by: rwatson
MFC after: 2 weeks
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
When enabled all TTY input queue buffers are zeroed when flushing or
closing the TTY. Because TTY input queues are also used to store filled
in passwords, this may be an interesting switch to enable for security
minded people.
1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.
Obtained from: Navdeep Parhar
MFC after: 10 days
and down more cleanly. This addresses a problem where if we have the
link flap during boot the driver would lock up the system.
Reviewed by: jhb
MFC after: 1 week
the behaviour alredy present with the further malloc() call in
devctl_notify().
This fixes a bug in the CAM layer where the camisr handler finished to
call camperiphfree() (and subsequently destroy_dev() resulting in a new
dev notify) while the xpt lock is held.
PR: kern/130330
Tested by: Riccardo Torrini <riccardo dot torrini at esaote dot com>
thread. Multiple RAID events in quick succession can cause an additional
bus rescan to be scheduled before an earlier scan has completed. In this
case the driver was attempting to use the same CCB storage for two requests.
PR: kern/130330
Reviewed by: Riccardo Torrini riccardo.torrini | esaote com
MFC after: 1 week
access windows. This eliminates hangs on systems which are configured to use
interleaved mode: prior to this fix we were simply cutting ourselves from
access to the main memory in this case.
Obtained from: Freescale, Semihalf
last year or two's work on routing:
- Combine iproute initialization and flowtable lookup blocks, eliminating
unnecessary tests for known-zero'd iproute fields.
- Add a comment indicating (a) why the route entry returned by the
flowtable is considered stable and (b) that the flowtable lookup must
occur after the setup of the mbuf flow ID.
- Assert the inpcb lock before any use of inpcb fields.
Reviewed by: kmacy
o Header file cleanup.
o bus_dma(9) conversion.
- Removed all consumers of vtophys(9) and converted to use
bus_dma(9).
- 64bit DMA support was disabled because DP83821 is not capable
of handling the DMA request. 64bit DMA request on DP83820
requires different descriptor structures and it's hard to
dynamically change descriptor format at run time so I disabled
it. Note, this is the same behavior as previous one but
previously nge(4) didn't explicitly disable 64bit mode on
DP83820.
- Added Tx/Rx descriptor ring alignment requirements(8 bytes
alignment).
- Limit maximum number of Tx DMA segments to 16. In fact,
controller does not seem to have limitations on number of Tx
DMA segments but 16 should be enough for most cases and
m_collapse(9) will handle highly fragmented frames without
consuming a lot of CPU cycles.
- Added Rx buffer alignment requirements(8 bytes alignment). This
means driver should fixup received frames to align on 16bits
boundary on strict-alignment architectures.
- Nuked driver private data structure in descriptor ring.
- Added endianness support code in Tx/Rx descriptor access.
o Prefer faster memory mapped register access to I/O mapped access.
Added fall-back mechanism to use alternative register access.
The hardware supports both memory and I/O mapped access.
o Added suspend/resume methods but it wasn't tested as controller I
have does not support PCI PME.
o Removed swap argument in nge_read_eeprom() since endianness
should be handled after reading EEPROM.
o Implemented experimental 802.3x full-duplex flow-control. ATM
it was commented out but will be activated after we have generic
flow-control framework in mii(4) layer.
o Rearranged promiscuous mode settings and simplified logic.
o Always disable Rx filter prior to changing Rx filter functions as
indicated in DP83820/DP83821 datasheet.
o Added an explicit DELAY in timeout loop of nge_reset().
o Added a sysctl variable dev.nge.%d.int_holdoff to control
interrupt moderation. Valid ranges are 1 to 255(default 1) in
units of 100us. The actual delivery of interrupt would be delayed
based on the sysctl value. The interface has to be brought down
and up again before a change takes effect. With proper tuning
value, users do not need to resort to polling(4) anymore.
o Added ALTQ(4) support.
o Added missing IFCAP_VLAN_HWCSUM as nge(4) can offload Tx/Rx
checksum calculation on VLAN tagged frames as well as VLAN tag
insertion/stripping. Also add IFCAP_VLAN_MTU capability as nge(4)
can handle VLAN tagged oversized frames.
o Fixed media header length for VLAN.
o Rearranged nge_detach routine such that it's now used for general
clean-up routine.
o Enabled MWI.
o Accessing EEPROM takes very long time so read 6 bytes ethernet
address with one call instead of 3 separate accesses.
o Don't set if_mtu in device attach, it's already set in
ether_ifattach().
o Don't do any special things for TBI interface. Remove TBI
specific media handling in the driver and have gentbi(4) handle
it. Add glue code to read/write TBI PHY registers in miibus
method. This change removes a lot of PHY handling code in driver
and now its functionality is handled by mii(4).
o Alignment fixup code is now applied only for strict-alignment
architectures. Previously the code was applied for all
architectures except i386. With this change amd64 will get
instant Rx performance boost.
o When driver fails to allocate a new mbuf, update if_qdrops so
users can see what was wrong in Rx path.
o Added a workaround for a hardware bug which resulted in short
VLAN tagged frames(e.g. ARP) was rejected as if runt frame was
received. With this workaround nge(4) now accepts the short VLAN
tagged frame and nge(4) can take full advantage of hardware VLAN
tag stripping. I have no idea how this bug wasn't known so far,
without the workaround nge(4) may never work on VLAN
environments.
o Fixed Rx checksum offload logic such that it now honors active
interface capability configured with ifconfig(8).
o In nge_start()/nge_txencap(), always leave at least one free
descriptor as indicated in datasheet. Without this the hardware
would be confused with ring descriptor structure(e.g. no clue
for the end of descriptor ring).
o Removed dead-code that checks interrupts on PHY hardware. The
code was designed to detect link state changes but it was
disabled as driving nge_tick clock would break auto-negotiation
timer. This code is no longer needed as nge(4) now uses mii(4)
and link state change handling is done with mii callback.
o Rearranged ethernet address programming logic such that it works
on strict-alignment architectures.
o Added IFCAP_VLAN_HWTAGGING/IFCAP_VLAN_HWCSUM handler in
nge_ioctl() such that the functionality is configurable with
ifconfig(8). DP83820/DP83821 can do checksum offload for VLAN
tagged frames so enable Tx/Rx checksum offload for VLAN
interfaces.
o Simplified IFCAP_POLLING selection logic in nge_ioctl().
o Fixed module unload panic when bpf listeners are active.
o Tx/Rx descriptor ring address uses 64bit DMA address for
readability. High address part of DMA would be 0 as nge(4)
disabled 64bit DMA transfers so it's ok for DP83821.
o Removed volatile keyword in softc as bus_dmamap_sync(9) should
take care of this.
o Removed extra driver private structures in descriptor ring. These
extra elements are not part of descriptor structure. Embedding
private driver structure into descriptor ring is not good idea
as its size may be different on 32bit/64bit architectures.
o Added miibus_linkchg method handler to catch link state changes.
o Removed unneeded nge_ifmedia in softc. All TBI access is handled
in gentbi(4). There is no difference between TBI and non-TBI case
now.
o Removed "gigabit link up" message handling in nge_tick. Link
state change notification is already performed by mii(4) and
checking link state by accessing PHY registers in periodic timer
handler of driver is wrong. All link state and speed/duplex
monitoring should be handled in PHY driver.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Added hardware MAC statistics counter, users canget current MAC
statistics from dev.nge.%d.stats sysctl node(%d is unit number of
a device).
o Removed unused macros, NGE_LASTDESC, NGE_MODE, NGE_OWNDESC,
NGE_RXBYTES.
o Increased number of Tx/Rx descriptors from 128 to 256. From my
experience on gigabit ethernet controllers, number of descriptors
should be 256 or higher to get an optimal performance on gigabit
link.
o Increased jumbo frame length to 9022 bytes to cope with other
gigabit ethernet drivers. Experimentation shows no problems with
9022 bytes.
o Removed unused member variables in softc.
o Switched from bus_space_{read|write}_4 to bus_{read|write}_4.
o Added support for WOL.
lock sysid to be used for non-nlm remote locking. This is required
for the experimental nfsv4 server, so that it can acquire byte
range locks correctly on behalf of nfsv4 clients.
Reviewed by: dfr
Approved by: kib (mentor)
route is also being deleted, the link-layer address table
(arp or nd6) will flush those L2 llinfo entries that match
the removed prefix.
Reviewed by: kmacy
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
when it runs out of clientids is reboot. I had replaced cpu_reboot()
with printf(), since cpu_reboot() doesn't exist for sparc64.
This change replaces the printf() with panic(), so the reboot
would occur for this highly unlikely occurrence.
Approved by: kib (mentor)
o Convert K&R function definitions to ANSI
o Eliminate spaces/tabs that should have been deleted as part of the de__P
efforts
o Use struct thread * in preference to d_thread_t *.
bug referencing a destroyed lock within TX callbacks during device
detach.
Submitted by: hps (original version)
Tested by: Lucius Windschuh <lwindschuh at googlemail.com>
shared uses of a resource are recorded on a sub-list hanging off
a main resource object on a main resource list;
without this change a shared resource (e.g. irq) is reported only
once by devinfo -r/-u;
with this change the resource is reported for each driver that
allocates it (which is even more than what vmstat -i -a reports).
Approved by: jhb (mentor)
Args argument is a pointer to the structure located in user space in
which the socketcall arguments are packed. The structure must be
copied to the kernel instead of direct dereferencing.
Approved by: kib (mentor)
MFC after: 1 week
net.inet.ip.fw.one_pass is a classic ip_input.c variable and is used in
the pfil and bridge code as well. As ipfw is loadable we need to always
provide it. That is the reason why it lives in struct vnet_inet and
not in struct vnet_ipfw.
machine check code. Disable it by default for now.
- When computing the mask of bits that determines a non-restartable event
during a machine check exception, or-in the overflow flag rather than
replacing the other flags.
PR: i386/134586 [2]
Submitted by: Andi Kleen andi-fbsd firstfloor.org
the NFSv4 Close operations until ncl_inactive(). This is
necessary so that the Open StateIDs are available for doing
I/O on mmap'd files after VOP_CLOSE(). I also changed some
indentation for the nfscl_getclose() function.
Approved by: kib (mentor)
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
register 0x52, not ctrl1. This appears to be a mistake in the bcm
reverse engineering page, and has been corrected there. Tracing
through the code, this is more in keeping with the "documented"
register. Sephe thinks it looks interesting and may be worth
fixing. :)
Submitted by: ddkprog at yahoo com
Reviewed by: Sepherosa Ziehau
affinity for the interrupt thread, and requesting that underlying
hardware direct interrupts to the CPU. For software interrupt
threads, implement a no-op interrupt event binder that returns
success, so that the interrupt management code will just set the
ithread's affinity and succeed.
Reviewed by: jhb
MFC after: 1 week
These sysctls don't need any form of locking. At least cp_times is used
by powerd very often, which means I get 50% less calls to non-MPSAFE
sysctls on my system. The other 50% is consumed by dev.cpu.0.freq, but
this seems to need Giant for Newbus.
-- A routing socket message is not generated when an IPv6 address is
either inserted or deleted from an interface. The missing routing
message problem was discovered by Randall Stewart and Michael Tuxen
during SCTP testing.
-- Previously when an IPv6 address is configured on an interface, if the
prefix length is /128, then a host route is instaleld in the kernel
for this address. But this host route is not deleted when that IPv6
address is removed from the interface.
-- Routes to the link-local all-nodes multicast address and the
interface-local all-nodes multicast address are not removed when
the last IPv6 address is removed from an interface.
Reviewed by: bz, gnn
- In bce_rx_intr(), use BUS_DMASYNC_POSTREAD instead of
BUS_DMASYNC_POSTWRITE, as we want to "read" from the
rx page chain pages.
- Document why we need to do PREWRITE after we have updated
the rx page chain pages.
- In bce_intr(), use BUS_DMASYNC_POSTREAD and
BUS_DMASYNC_PREREAD when before and after CPU "reading"
the status block.
- Adjust some nearby style mismatches/etc.
Pointed out by: yongari
Approved by: davidch (no objection) but bugs are mine :)
# Note: The driver doesn't support either these PHY types, so this is
# effectively a nop.
Submitted by: "ddk"
Obtained from: http://paradox.lissyara.su/bwi.diff
made LINT happy this does the proper looping over all vnets as we are
only called `globally' and not once per vnet instance.
Reported by: zec [1]
Missed by: bz [1] in r192264
Reviewed by: zec
believe it was a BCM4319. However, it is the a/b/g variation of the
BCM4318. The chip itself is labelled BCM4318EKFBG, and the board is
BCM94318MKABG.
Paradox's patch includes the type of 802.11 wireless for each card,
but changes all the names (I don't think the latter is quite right).
Import that part of the patch, but keep the current set of BCM names
(with a minor tweak for the 4306 ones). I'll need to verify them via
some other means.
Obtained from: http://paradox.lissyara.su/bwi.diff (partially)
Provide a more descriptive comment.
Eliminate dead code. The page cannot possibly have PG_ZERO set.
Eliminate unnecessary blank lines.
Reviewed by: tegge
experimental nfsv4 server. It was setting the a_id argument
to a fixed value, but that wasn't sufficient for FreeBSD8.
Instead, set l_pid and l_sysid to 0 plus set the F_REMOTE
flag to indicate that these fields are used to check for
same lock owner. Since, for NFSv4, a lockowner is a ClientID plus
an up to 1024byte name, it can't be put in l_sysid easily.
I also renamed the p variable to td, since it's a thread ptr.
Approved by: kib (mentor)
nfsrv_dolocallocks can be changed via sysctl. I also added some non-empty
descriptor strings and reformatted some overly long lines.
Approved by: kib (mentor)
This makes siginfo output look a lot better when pressing it the first
time when in sh(1), for example:
$ load: 0.00 cmd: sh 1945 [ttyin] 3.94r 0.00u 0.00s 0% 1960k
load: 0.00 cmd: sh 1945 [ttyin] 4.19r 0.00u 0.00s 0% 1960k
will now become:
$
load: 0.00 cmd: sh 1945 [ttyin] 3.94r 0.00u 0.00s 0% 1960k
load: 0.00 cmd: sh 1945 [ttyin] 4.19r 0.00u 0.00s 0% 1960k
- Only pick up PROC_LOCK once, which means we can drop the PGRP_LOCK
right after picking up PROC_LOCK for the first time.
- Print the process real time, making it consistent with tools like
time(1).
- Use `p' and `td' to reference the process/thread we are going to
print. Only use pick-variables inside the loops. We already did this
for the threads, but not the processes.
SOCK_NONBLOCK flags, that allow to save fcntl() calls.
Implement a variation of the socket() syscall which takes a flags
in addition to the type argument.
Approved by: kib (mentor)
MFC after: 1 month
Temporarily use 0 for pid member as the FreeBSD does not cache remote
UNIX domain socket peer pid.
PR: kern/102956
Reviewed by: rwatson
Approved by: kib (mentor)
MFC after: 1 month