possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
directly in cpu_reset() in order to idle the APs before exiting
the kernel and letting the BSP enter the firmware so that processes
like init(8) which still might be running on an AP at that point
don't cause a panic there when it crashes due to the fact it no
longer can be supported by the kernel.
MFC after: 3 days
a fair number of static data structures, making this an unlikely
option to try to change without also changing source code. [1]
Change default cache line size on ia64, sparc64, and sun4v to 128
bytes, as this was what rtld-elf was already using on those
platforms. [2]
Suggested by: bde [1], jhb [2]
MFC after: 2 weeks
CACHE_LINE_SIZE constant. These constants are intended to
over-estimate the cache line size, and be used at compile-time
when a run-time tuning alternative isn't appropriate or
available.
Defaults for all architectures are 64 bytes, except powerpc
where it is 128 bytes (used on G5 systems).
MFC after: 2 weeks
Discussed on: arch@
1) Move the new field (brand_note) to the end of the Brandinfo structure.
2) Add a new flag BI_BRAND_NOTE that indicates that the brand_note pointer
is valid.
3) Use the brand_note field if the flag BI_BRAND_NOTE is set and as old
modules won't have the flag set, so the new field brand_note would be
ignored.
Suggested by: jhb
Reviewed by: jhb
Approved by: kib (mentor)
MFC after: 6 days
supported burst sizes.
- Add support for 64-bit burst sizes (required for SBus GEM).
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
- Failing to register as interrupt controller during attach shouldn't
be fatal so just inform about this instead of panicing.
- Disable rerun of the streaming cache as workaround for a silicon bug
of certain Psycho versions.
- Remove the comment regarding lack of newbus'ified bus_dma(9) as being
able to associate a DMA tag with a device would allow to implement
CDMA flushing/syncing in bus_dmamap_sync(9) but that would totally
kill performance. Given that for devices not behind a PCI-PCI bridge
the host-to-PCI bridges also only do CDMA flushing/syncing based on
interrupts there's no additional disadvantage for polling(4) callbacks
in the case schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.
- Don't panic if the power failure, power management or over-temperature
interrupts doesn't exist as these aren't mandatory and not available
with all controllers (not even Psychos). [1]
- Take advantage of KOBJMETHOD_END.
- Remove some redundant variables.
- Add missing const.
PR: 131371 [1]
- Hook up the streaming buffer (not used by iommu(4) by default, yet)
if available and usable. [1]
- Move the message regarding belated registration as interrupt control
under bootverbose as this isn't something the user should worry about.
Tested by: Michael Moll [1]
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
".note.ABI-tag" section.
The search order of a brand is changed, now first of all the
".note.ABI-tag" is looked through.
Move code which fetch osreldate for ELF binary to check_note() handler.
PR: 118473
Approved by: kib (mentor)
kernel one as the non-faulting flush address in the loader so
we can can change KERNBASE and VM_MIN_KERNEL_ADDRESS if we
ever want to without needing to worry about using a compatible
loader.
- Correctly check for LOADER_DEBUG.
- Add a missing const for page_sizes[].
whole KVA space using one locked 4MB dTLB entry per GB of physical
memory. On Cheetah-class machines only the dt16 can hold locked
entries though, which would be completely consumed for the kernel
TSB on machines with >= 16GB. Therefore limit the KVA space to use
no more than half of the lockable dTLB slots, given that we need
them also for other things.
- Add sanity checks which ensure that we don't exhaust the (lockable)
TLB slots.
firmware versions which wedge when using the OFW test service,
so given that we don't really depend on SUNW,stop-self just nuke
it altogether instead of risking problems.
- At least Fire V880 have a small hardware glitch which causes the
reception of IDR_NACKs for CPUs we actually haven't tried to send
an IPI to, even not as part of the initial try. According to tests
this apparently can be safely ignored though, so just return if
checking for the individual IDR_NACKs indicates no outstanding
dispatch. Serializing the sending of IPIs between MD and MI code
by the combined usage of smp_ipi_mtx makes no difference to this
phenomenon. [1]
- Provide relevant debugging bits already with the initial panic
in case of problems with the IPI dispatch, which would have
allowed to diagnose the above problem without a specially built
kernel.
- In case of cheetah_ipi_selected() base the delay we wait for
other CPUs which also might want to dispatch IPIs on the total
amount of CPUs instead of just the number of CPUs we let this
CPU send IPIs to because in the worst case all CPUs also want
to IPI us at the same time.
Reported and access for extensive tests provided by: Beat Gaetzi [1]
of OFW access semantics, in order to allow future support for real-mode
OF access and flattened device frees. OF client interface modules are
implemented using KOBJ, in a similar way to the PPC PMAP modules.
Because we need Open Firmware to be available before mutexes can be used on
sparc64, changes are also included to allow KOBJ to be used very early in
the boot process by only using the mutex once we know it has been initialized.
Reviewed by: marius, grehan
be fatal so just inform about this instead of panicing.
- Ensure we use the right softc in case the interrupt of a child is
is routed to the companion PBM instead. This hasn't been seen in the
wild so far but given that it's the case for the Schizo interrupts,
handling this situation also for child interrupts as a precaution
seemed a good idea.
- Deal with broken firmware versions which miss child entries in the
ino-bitmap as seen on V880 by belatedly registering as interrupt
controller in schizo_setup_intr(). [1]
- Add missing '\n' when printing the warning regarding Schizo Errata
I-13.
Reported and tested by: Beat Gaetzi [1]
the code for parsing interrupt maps) to PowerPC and reflect their new MI
status by moving them to the shared dev/ofw directory.
This commit also modifies the OFW PCI enumeration procedure on PowerPC to
allow the bus to find non-firmware-enumerated devices that Apple likes to add,
and adds some useful Open Firmware properties (compat and name) to the pnpinfo
string of children on OFW SBus, EBus, PCI, and MacIO links. Because of the
change to PCI enumeration on PowerPC, X has started working again on PPC
machines with Grackle hostbridges.
Reviewed by: marius
Obtained from: sparc64
Sgtty is a programming interface that has been replaced by termios over
the years. In June we already removed <sgtty.h>, which exposes the
ioctl()'s that are implemented by this interface. The importance of this
flag is overrated right now.
module; the ath module now brings in the hal support. Kernel
config files are almost backwards compatible; supplying
device ath_hal
gives you the same chip support that the binary hal did but you
must also include
options AH_SUPPORT_AR5416
to enable the extended format descriptors used by 11n parts.
It is now possible to control the chip support included in a
build by specifying exactly which chips are to be supported
in the config file; consult ath_hal(4) for information.
of the ABI of the currently executing image. Change some places to test
the flags instead of explicit comparing with address of known sysentvec
structures to determine ABI features.
Discussed with: dchagin, imp, jhb, peter
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
and XMITS has to be basically done in the same manner as for
the Sabres, i.e. only for devices behind PCI-PCI-bridges and
after a PIO read on the far side of the farest PCI-PCI-bridge.
Given that the Tomatillo documentation mentions no difference
to the Schizo bridges in this regard and this is also still
part of the procedure described Schizo documentation this
seems about right so adjust accordingly (the unconditional
CDMA flushing/syncing previously done was based on how Linux
behaves).
- Implement CDMA flushing/syncing for Schizo version >= 5,
which requires the workaround described in Schizo Errata I-23.
According to Schizo Errata I-13 it's just unusable with
version < 5 though. [1]
- Don't register the Schizo streaming buffer for now until it's
usage is sorted out according to the erratas.
- Register our interrupt filters with the revived INTR_FAST so
they these interrupts can even interrupt filters of device
drivers as necessary.
- Remove the comment regarding lack of newbus'ified bus_dma(9)
as being able to associate a DMA tag with a device would
allow to implement CDMA flushing/syncing in bus_dmamap_sync(9)
but that would totally kill performance. Given that for devices
not behind a PCI-PCI bridge the host-to-PCI bridges also only
do CDMA flushing/syncing based on interrupts there's no
additional disadvantage for polling(4) callbacks in the case
schizo(4) has to do the CDMA flushing/syncing but rather a
general problem.
Reported by: Michael Moll [1]
filters instead of PIL_FAST and allow special filters and handlers
for interrupts which need to be able to interrupt even filters, f.e.
bus error interrupts, to be registered with the revived INTR_FAST
at PIL_FAST.
rerun of the streaming cache for silicon bug workarounds.
- Announce the presence of a streaming cache on attach for
informational purposes.
- For performance reasons don't do unnecessary flushes of the
streaming cache when coherent mappings are synced.
- Fix some minor style issues.
class CPUs. In theory one could also use versions additionally
taking advantage of the prefetch cache with cheetah-class CPUs,
in my worldstone runs these either didn't provide extra speedup
(USIII+) in comparison to the existing spitfire versions or were
even slightly slower (USIIIi) though, so they aren't committed
for now.
The basic problem leading to the VIS-based copy/zero functions
being initially disabled for cheetah-class CPUs was solved by
letting cheetah_init() clear DCR_IFPOE.
while doing the block store workaround so we restore the correct
floating-point registers state in case of nested floating-point
operations resulting from nested interrupts. This allows the
VIS-based block copy/zero functions to be used on machines
requiring this workaround. Alternatively, we could take care of
saving the floating-point registers here, which would be more
inefficiently though and also involves turning off interrupts.
- It turns out that the SCZ_PCI_DMA_SYNC register doesn't work
like the TOMXMS_PCI_DMA_SYNC_PEND one (but more like the
corresponding register in of Hummingbird and Sabre bridges)
and writing the INO of the respective device to it causes a
Safari bus error. However, due to the Schizo errata I-23,
SCZ_PCI_DMA_SYNC can't be used as intended either, so remove
consistent DMA syncing for Schzio bridges for now, which means
that add-on cards with non-"sun4u compliant" (whatever that
means exactly) PCI-PCI-bridges should be avoided until the
proper workaround is implemented. [1]
Reported by: Michael Moll [1]
V9 stack bias so we no longer need to add it in db_backtrace()
and stack_capture() respectively. This also reverts r182018,
which kludged around the resulting unaligned access.
- Sync the sun4v versions of db_trace.c and stack_machdep.c with
the sparc64 ones and fix some style bugs.
MFC after: 3 days
controllers and it seems to work just fine with at least an
add-on SAS3080X. While at it, remove the commented out ncr(4)
as it doesn't even use bus_dma(9), which isn't worth fixing
though as sym(4) already supports a superset of the controllers
driven by ncr(4).
JBus to PCI 2.2 bridges. In theory, this driver should also handle
`XMITS' Fireplane/Safari to PCI-X bridges but due to lack of access
to such hardware, support for these hasn't be fleshed out, yet.
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
to the C99 style. At least, it is easier to read sysent definitions
that way, and search for the actual instances of sigcode etc.
Explicitely initialize sysentvec.sv_maxssiz that was missed in most
sysvecs.
No objection from: jhb
MFC after: 1 month
consists of CPUs running at different speeds, for driving hardclock as
these timers in turn are driven at frequencies as low as 5MHz, resulting
in bad granularity compared to the TICK timers. However, don't employ
the workaround for the BlackBird erratum #1 when using the TICK timer
on machines with cheetah-class CPUs for performance reasons.
Reported by: Florian Smeets
could trigger an error interrupt that we can't actually to do anything
against as soon as enabling the error handlers.
While at it don't bother about writing only to the write-one-to-clear
bits when clearing error bits.
disable interrupts and loop forever with these.
- Hide all MP-related bits in <machine/smp.h> underneath #ifdef SMP.
- Inline ipi_all_but_self(9) and ipi_selected(9). We don't expose any
additional bits but save a few cycles by doing so.
- Remove ipi_all(9), which actually only called panic(9). It can't be
implemented natively anyway and having it removed at least causes
MI users to fail already fail when linking.
Safari- and JBus-based machines. Currently the main purpose of
these drivers is debugging of the resource allocation on nexus(4)
and the register content of these devices though.
the locked entry in it16 slot 0, which typically is occupied by the
PROM, and manually entering locked entries in slots != 0.
Thanks to Hubert Feyrer for donating the Blade 2000 this change was
developed on.
for all three contexts and configure the dt512_1 to hold 4MB pages for
them (e.g. for direct mappings).
This might allow for additional optimization by using the faulting
page sizes provided by AA_DMMU_TAG_ACCESS_EXT for bypassing the page
size walker for the dt512 in the superpage support code.
Submitted by: nwhitehorn (initial patch)
to synchronization needed after stores to internal ASIs in order
to make side-effects visible. This mainly requires the MEMBAR #Sync
after such stores to be replaced with a FLUSH. We use KERNBASE as
the address to FLUSH as it is guaranteed to not trap. Actually,
the USII synchronization rules also already require a FLUSH in
pretty much all of the cases changed.
We're also hitting an additional USIII synchronization rule which
requires stores to AA_IMMU_SFSR to be immediately followed by a DONE,
FLUSH or RETRY. Doing so triggers a RED state exception though so
leave the MEMBAR #Sync. Linux apparently also has gotten away with
doing the same for quite some time now, apart from the fact that
it's not clear to me why we need to clear the valid bit from the
SFSR in the first place.
Reviewed by: nwhitehorn
the ncr53c9x.c core where it actually belongs so future front-ends
don't need to add it.
o Use the correct OFW property when looking for the initiator ID of the
SBus device.
o Don't specify an alignment when creating the parent DMA tag for
SUNW,fas; their DMA engine doesn't require an alignment constraint
and it's no inherited by the child DMA tags anyway (which probably
is a bug though).
o Drop the superfluous sc_maxsync and use sc_minsync instead. The
former apparently was added due to a confusion with the maximum
frequency used in cam(4), which basically corresponds to the
inverse of minimum sync period.
o Merge ncr53c9x.c from NetBSD:
1.116: NCRDMA_SETUP() should be called before NCR_SET_COUNT() and
NCRCMD_DMA command in ncr53c9x_select().
1.125: free allocated resources on detach.
o Static'ize ncr53c9x_action(), ncr53c9x_init() and ncr53c9x_reset()
as these are not required outside of ncr53c9x.c.
o In ncr53c9x_attach() don't leak the device mutex in case attaching
fails.
o Register an asynchronous notification handler so in case cam(4)
reports a lost device we can cancel outstanding commands and
restore the default parameters for the target in question.
o For FAS366 correctly support 16-bit target IDs and let it know
that we use 32-bit transfers.
o Overhaul the negotiation of transfer settings. This includes
distinguishing between current and goal transfer settings of the
target so we can renegotiate their goal settings when necessary
and correcting the order in which tagged, wide and synchronous
transfers are negotiated.
o If we are requesting sense, force a renegotiation if we are
currently using anything different from asynchronous at 8 bit
as the target might have lost our transfer negotiations.
o In case of an XPT_RESET_BUS just directly call ncr53c9x_init()
instead of issuing a NCRCMD_RSTSCSI, which in turn will issue an
interrupt that is treated as an unexpected SCSI bus reset by
ncr53c9x_intr() and thus calls ncr53c9x_init(). Remove the now
no longer used ncr53c9x_scsi_reset().
o Correct an off-by-one error when setting cpi->max_lun.
o In replace printf(9) with device_printf(9) calls where appropriate
and in ncr53c9x_action() remove some unnecessarily verbose messages.
o In ncr53c9x_sched() use TAILQ_FOREACH() instead of reimplementing
it and consolidate two tagging-related target info checks into one.
o In ncr53c9x_done() set the CAM status to CAM_SCSI_STATUS_ERROR when
appropriate, respect CAM_DIS_AUTOSENSE and teach it to return SCSI
status information.
o In ncr53c9x_dequeue() ensure the tags are cleared.
o Use ulmin() instead of min() where appropriate.
o In ncr53c9x_msgout() consistently use the reset label.
o When we're interrupted during a data phase and the DMA engine is
still active, don't panic but reset the core and the DMA engine as
this should be sufficient. Also, the typical problem for triggering
this was the lack of renegotiation when requesting sense.
o Correctly handle DEVICE RESETs.
o Adapt the locking of esp(4) to MPSAFE cam(4). This includes moving
the calls of lsi64854_attach() to the bus front-ends so it can pass
the esp(4) mutex to bus_dma_tag_create(9).
o Change the LSI64854 driver to not create a DMA tag and map for the
Ethernet channel as le(4) will handle these on its own as well as
sync and unload the DMA maps for the SCSI and parallel port channel
after a DMA transfer.
o Cam(4)'ify some NetBSD-centric comments.
o Use bus_{read,write}_*(9) instead of bus_space_{read,write}_*(9)
and take advantage of rman_get_rid(9) in order to save some softc
members.
Reviewed by: scottl
MFC after: 1 month
table. This is required in order to set obp-control-relinquished
within the PROM, allowing to safely read the OFW translations node.
Without this, f.e. a `ofwdump -ap` triggers a fatal reset error or
worse things on machines based on USIII and beyond.
In theory this should allow to remove touching %tba in cpu_setregs(),
in practice we seem to currently face a chicken and egg problem when
doing so however.
to 43 bits so update TD_PA_BITS accordingly. For the most part this
increase is transparent to the existing code except for when reading
the physical address from ASI_{D,I}TLB_DATA_ACCESS_REG, which we
only do in the loader and which was already adjusted in r182478, or
from the OFW translations node.
While at it, ensure we are only taking valid OFW mapping entries
into account.
frequencies (and having different cache sizes) so use the STICK
(System TICK) timer, which was introduced due to this and is
driven by the same frequency across all CPUs, instead of the
TICK timer, whose frequency varies with the CPU clock, to drive
hardclock. We try to use the STICK counter with all CPUs that are
USIII or beyond, even when not necessary due to identical CPUs,
as we can can also avoid the workaround for the BlackBird erratum
#1 there. Unfortunately, using the STICK counter currently causes
a hang with USIIIi MP machines for reasons unknown, so we still
use the TICK timer there (which is okay as they can only consist
of identical CPUs).
- Given that we only (try to) synchronize the (S)TICK timers of APs
with the BSP during startup, we could end up spinning forever in
DELAY(9) if that function is migrated to another CPU while we're
spinning due to clock drift afterwards, so pin to the CPU in order
to avoid migration. Unfortunately, pinning doesn't work at the
point DELAY(9) is required by the low-level console drivers, yet,
so switch to a function pointer, which is updated accordingly, for
implementing DELAY(9). For USIII and beyond, this would also allow
to easily use the STICK counter instead of the TICK one here,
there's no benefit in doing so however.
While at it, use cpu_spinwait(9) for spinning in the delay-
functions. This currently is a NOP though.
- Don't set the TICK timer of the BSP to 0 during at startup as
there's no need to do so.
- Implement cpu_est_clockrate().
- Unfortunately, USIIIi-based machines don't provide a timecounter
device besides the STICK and TICK counters (well, in theory the
Tomatillo bridges have a performance counter that can be (ab)used
as timecounter by configuring it to count bus cycles, though unlike
the performance counter of Schizo bridges, the Tomatillo one is
broken and counts Sun knows what in this mode). This means that
we've to use a (S)TICK counter for timecounting, which has the old
problem of not being in sync across CPUs, so provide an additional
timecounter function which binds itself to the BSP but has an
adequate low priority.
sizes (and running at different frequencies) so move the cacheinfo
to the PCPU data. While at it, remove some redundant and/or unused
members from struct cacheinfo.
- In sparc64_init don't assume the first CPU node we find in the OFW
device tree is the BSP.
in order to avoid the invasive probes done by identify-routines of
ISA drivers, which may access unassigned addresses or those of
unrelated devices and thus in turn can trigger master/target aborts
as revealed by r182108 and ahc(4). I think that this is also the
cause of the hang previously seen on B100 blades during boot.
Bypassing isa_probe_children(9) also avoids adding ISA hints, which
just can be wrong for sparc64.
Reported by: gavin
in the kernel and copying it out, causing a panic when faulting on a
nofault entry. Handle this case gracefully by letting the kernel copy
functions return EFAULT instead. As such this change addresses the
same problem as r154721 does for i386.
MFC after: 3 days
In syscall, always make a copy of parameters from trapframe, this
becauses some syscalls using set_mcontext can sneakily change
parameters and later when those syscalls references parameters,
they will wrongly use register values in mcontext_t.
PR: 72998
MFC after: 3 days
the latency based on the Min_Gnt register so use the algorithm found
in OpenSolaris as they probably know how to interpret the value Sun
puts into these registers (previously, the latency calculated for
66MHz was most likely wrong) and for bridges additionally set up the
secondary latency register. Also set up the bridge control register
the way it's done in OpenSolaris. As the latency register don't apply
to PCI-Express and the bridge control setup wasn't tested on sun4v
(besides most likely not being needed), expand the #ifndef SUN4V
accordingly.
MFC after: 3 days
- Provide module dependency information.
- Static'ize ebus_release_resource() in order to match prototype.
- Remove outdated and/or obsolete comments.
- Fix whitespace bugs.
MFC after: 3 days
on the presence of fhc(4) instead; we by far don't support all of
the functionality provide by the clock board but in general it's
an integral part of FireHose-based systems which shouldn't be
possible to omit.
ukbd(4) does and that emulation was enabled by default, all three of
them work together with kbdmux(4) out of the box just fine.
- Fix some whitespace bugs.
MFC after: 3 days
The last half year I've been working on a replacement TTY layer for the
FreeBSD kernel. The new TTY layer was designed to improve the following:
- Improved driver model:
The old TTY layer has a driver model that is not abstract enough to
make it friendly to use. A good example is the output path, where the
device drivers directly access the output buffers. This means that an
in-kernel PPP implementation must always convert network buffers into
TTY buffers.
If a PPP implementation would be built on top of the new TTY layer
(still needs a hooks layer, though), it would allow the PPP
implementation to directly hand the data to the TTY driver.
- Improved hotplugging:
With the old TTY layer, it isn't entirely safe to destroy TTY's from
the system. This implementation has a two-step destructing design,
where the driver first abandons the TTY. After all threads have left
the TTY, the TTY layer calls a routine in the driver, which can be
used to free resources (unit numbers, etc).
The pts(4) driver also implements this feature, which means
posix_openpt() will now return PTY's that are created on the fly.
- Improved performance:
One of the major improvements is the per-TTY mutex, which is expected
to improve scalability when compared to the old Giant locking.
Another change is the unbuffered copying to userspace, which is both
used on TTY device nodes and PTY masters.
Upgrading should be quite straightforward. Unlike previous versions,
existing kernel configuration files do not need to be changed, except
when they reference device drivers that are listed in UPDATING.
Obtained from: //depot/projects/mpsafetty/...
Approved by: philip (ex-mentor)
Discussed: on the lists, at BSDCan, at the DevSummit
Sponsored by: Snow B.V., the Netherlands
dcons(4) fixed by: kan
virtualization work done by Marko Zec (zec@).
This is the first in a series of commits over the course
of the next few weeks.
Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.
We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.
Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch
no particular reason for them to be implemented in assembler and
having them in C allows easier extension as well as using more C
macros and {d,i}tlb_slot_max rather than hard-coding magic (and
actually spitfire-only) values.
- Fix the compilation of pmap_print_tte().
- Change pmap_print_tlb() to use ldxa() rather than re-rolling it
inline as well as TLB_DAR_SLOT and {d,i}tlb_slot_max rather than
hardcoding magic (and actually spitfire-only) values.
- While at it, suffix the above mentioned functions with "_sun4u" to
underline they're architecture-specific.
- Use __FBSDID and macros instead of magic values in locore.S.
- Remove unused includes and smp_stack in locore.S.
As clearly mentioned on the mailing lists, there is a list of drivers
that have not been ported to the MPSAFE TTY layer yet. Remove them from
the kernel configuration files. This means people can now still use
these drivers if they explicitly put them in their kernel configuration
file, which is good.
People should keep in mind that after August 10, these drivers will not
work anymore. Even though owners of the hardware are capable of getting
these drivers working again, I will see if I can at least get them to a
compilable state (if time permits).
into a single "__asm"-statement as GCC doesn't guarantee their
consecutive output even when using consecutive "__asm __volatile"-
statement for them. Remove the otherwise unnecessary "__volatile". [1]
- The inline assembler instructions used here alter the condition
codes so add them to the clobber list accordingly.
- The inline assembler instructions used here uses output operands
before all input operands are consumed so add appropriate modifiers.
Pointed out by: bde [1]
MFC after: 2 weeks
that modify condition codes (the carry bit, in this case). Without
"__volatile", the compiler might add the inline assembler instructions
between unrelated code which also uses condition codes, modifying the
latter.
This prevents the TCP pseudo header checksum calculation done in
tcp_output() from having effects on other conditions when compiled
with GCC 4.2.1 at "-O2" and "options INET6" left out. [1]
Reported & tested by: Boris Kochergin [1]
MFC after: 3 days
Now that st_rdev is being automatically generated by the kernel, there
is no need to define static major/minor numbers for the iodev and
memdev. We still need the minor numbers for the memdev, however, to
distinguish between /dev/mem and /dev/kmem.
Approved by: philip (mentor)
for UPA it should have fulfilled its purpose by now and Fireplane-
and JBus-based machines are way to messy in organization to implement
something equivalent.
- Fix a bunch of style(9) bugs.
counter-timer timecounter so the associated SYSCTL nodes don't clash on
machines having multiple U2P and U2S bridges as well as establishing a
clear mapping between these bridges and their timecounter device.
- Don't bother setting up a "nice" name for the IOMMU, just use the name
returned by device_get_nameunit(9), too.
- Fix some minor style(9) bugs.
- Use __FBSDID in counter.c
MFC after: 1 week
infrastructure. Its only consumer ever was sio(4) and thus was
unused on sparc64 since removing the last traces of sio(4) in
sparc64 configuration files in favor for uart(4) over three
years ago. If similar functionality is required again it should
be brought back as an MD intr_pending() which works for all
busses by using for example interrupt controller hooks.
from idle over the next tick.
- Add a new MD routine, cpu_wake_idle() to wakeup idle threads who are
suspended in cpu specific states. This function can fail and cause the
scheduler to fall back to another mechanism (ipi).
- Implement support for mwait in cpu_idle() on i386/amd64 machines that
support it. mwait is a higher performance way to synchronize cpus
as compared to hlt & ipis.
- Allow selecting the idle routine by name via sysctl machdep.idle. This
replaces machdep.cpu_idle_hlt. Only idle routines supported by the
current machine are permitted.
Sponsored by: Nokia
don't send and EOI which works like on amd64/i386 and blocks all
interrupts on the relevant interrupt controller.
o Replace the post_filter and post_inthread hooks registered when
creating the interrupt events with just ic_clear as on sparc64 we
don't need to do any disable->EOI->enable dance to unblock all but
the relevant interrupt while running the filter or handler; just
not clearing the interrupt already has the same effect.
o Merge from amd64/i386:
- Split the intr_table_lock into an sx lock used for most things,
and a spin lock to protect intrcnt_index.
- Add support for binding interrupts to CPUs, including for the
bus_bind_intr(9) interface, a assign_cpu hook and initially
shuffling interrupts arround in a round-robin fashion.
Reviewed by: jhb
MFC after: 1 month
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
have separate configuration spaces so by definition they implement
different PCI domains. Thus change psycho(4) to use PCI domains
instead of reenumerating all PCI busses so they have globally unique
bus numbers and drop support for reenumerating busses in the OFW PCI
code.
According to CVS history reenumeration was also required in order to
get some E450 to boot but given that no other open source kernel
changes the PCI bus numbers assigned by the firmware I believe the
real problem was that the old code used the bus number as the device
number for the PCI busses and unlike most of the other machines the
firmwares of the problematic ones don't use disjoint PCI bus numbers
across the host-PCI-bridges.
MFC after: 1 month
lookup hard interrupt events by number. Ignore the irq# for soft intrs.
- Add support to cpuset for binding hardware interrupts. This has the
side effect of binding any ithread associated with the hard interrupt.
As per restrictions imposed by MD code we can only bind interrupts to
a single cpu presently. Interrupts can be 'unbound' by binding them
to all cpus.
Reviewed by: jhb
Sponsored by: Nokia
allows all the INTR_FILTER #ifdef's to be removed from the MD interrupt
code.
- Rename the intr_event 'eoi', 'disable', and 'enable' hooks to
'post_filter', 'pre_ithread', and 'post_ithread' to be less x86-centric.
Also, add a comment describe what the MI code expects them to do.
- On amd64, i386, and powerpc this is effectively a NOP.
- On arm, don't bother masking the interrupt unless the ithread is
scheduled in the non-INTR_FILTER case to match what INTR_FILTER did.
Also, don't bother unmasking the interrupt in the post_filter case if
we never masked it. The INTR_FILTER case had been doing this by having
arm_unmask_irq for the post_filter (formerly 'eoi') hook.
- On ia64, stray interrupts are now masked for the non-INTR_FILTER case.
They were already masked in the INTR_FILTER case.
- On sparc64, use the a NULL pre_ithread hook and use intr_enable_eoi() for
both the 'post_filter' and 'post_ithread' hooks to match what the
non-INTR_FILTER code did.
- On sun4v, retire the ithread wrapper hack by using an appropriate
'post_ithread' hook instead (it's what 'post_ithread'/'enable' was
designed to do even in 5.x).
Glanced at by: piso
Reviewed by: marius
Requested by: marius [1], [5]
Tested on: amd64, i386, arm, sparc64
to detect (or load) kernel NLM support in rpc.lockd. Remove the '-k'
option to rpc.lockd and make kernel NLM the default. A user can still
force the use of the old user NLM by building a kernel without NFSLOCKD
and/or removing the nfslockd.ko module.
these days, so de-generalize the acquire_timer/release_timer api
to just deal with speakers.
The new (optional) MD functions are:
timer_spkr_acquire()
timer_spkr_release()
and
timer_spkr_setfreq()
the last of which configures the timer to generate a tone of a given
frequency, in Hz instead of 1/1193182th of seconds.
Drop entirely timer2 on pc98, it is not used anywhere at all.
Move sysbeep() to kern/tty_cons.c and use the timer_spkr*() if
they exist, and do nothing otherwise.
Remove prototypes and empty acquire-/release-timer() and sysbeep()
functions from the non-beeping archs.
This eliminate the need for the speaker driver to know about
i8254frequency at all. In theory this makes the speaker driver MI,
contingent on the timer_spkr_*() functions existing but the driver
does not know this yet and still attaches to the ISA bus.
Syscons is more tricky, in one function, sc_tone(), it knows the hz
and things are just fine.
In the other function, sc_bell() it seems to get the period from
the KDMKTONE ioctl in terms if 1/1193182th second, so we hardcode
the 1193182 and leave it at that. It's probably not important.
Change a few other sysbeep() uses which obviously knew that the
argument was in terms of i8254 frequency, and leave alone those
that look like people thought sysbeep() took frequency in hertz.
This eliminates the knowledge of i8254_freq from all but the actual
clock.c code and the prof_machdep.c on amd64 and i386, where I think
it would be smart to ask for help from the timecounters anyway [TBD].
- Always include the ie_disable and ie_eoi methods in 'struct intr_event'
and collapse down to one intr_event_create() routine. The disable and
eoi hooks simply aren't used currently in the !INTR_FILTER case.
- Expand 'disab' to 'disable' in a few places.
- Use function casts for arm and i386:intr_eoi_src() instead of wrapper
routines since to trim one extra indirection.
Compiled on: {arm,amd64,i386,ia64,ppc,sparc64} x {FILTER, !FILTER}
Tested on: {amd64,i386} x {FILTER, !FILTER}
after each SYSINIT() macro invocation. This makes a number of
lightweight C parsers much happier with the FreeBSD kernel
source, including cflow's prcc and lxr.
MFC after: 1 month
Discussed with: imp, rink
- Add a new intr_event method ie_assign_cpu() that is invoked when the MI
code wishes to bind an interrupt source to an individual CPU. The MD
code may reject the binding with an error. If an assign_cpu function
is not provided, then the kernel assumes the platform does not support
binding interrupts to CPUs and fails all requests to do so.
- Bind ithreads to CPUs on their next execution loop once an interrupt
event is bound to a CPU. Only shared ithreads are bound. We currently
leave private ithreads for drivers using filters + ithreads in the
INTR_FILTER case unbound.
- A new intr_event_bind() routine is used to bind an interrupt event to
a CPU.
- Implement binding on amd64 and i386 by way of the existing pic_assign_cpu
PIC method.
- For x86, provide a 'intr_bind(IRQ, cpu)' wrapper routine that looks up
an interrupt source and binds its interrupt event to the specified CPU.
MI code can currently (ab)use this by doing:
intr_bind(rman_get_start(irq_res), cpu);
however, I plan to add a truly MI interface (probably a bus_bind_intr(9))
where the implementation in the x86 nexus(4) driver would end up calling
intr_bind() internally.
Requested by: kmacy, gallatin, jeff
Tested on: {amd64, i386} x {regular, INTR_FILTER}
While the KSE project was quite successful in bringing threading to
FreeBSD, the M:N approach taken by the kse library was never developed
to its full potential. Backwards compatibility will be provided via
libmap.conf for dynamically linked binaries and static binaries will
be broken.
tree structure that encodes the level of cache sharing and other
properties.
- Provide several convenience functions for creating one and two level
cpu trees as well as a default flat topology. The system now always
has some topology.
- On i386 and amd64 create a seperate level in the hierarchy for HTT
and multi-core cpus. This will allow the scheduler to intelligently
load balance non-uniform cores. Presently we don't detect what level
of the cache hierarchy is shared at each level in the topology.
- Add a mechanism for testing common topologies that have more information
than the MD code is able to provide via the kern.smp.topology tunable.
This should be considered a debugging tool only and not a stable api.
Sponsored by: Nokia
sectors so the geometry of large IDE disks has to be adjusted. This
corresponds to what the OpenSolaris dad(7D) driver does except that
the latter only tweaks sectors and effectively limits the mediasize
to 128GB so the cylinders and heads fields won't ever overflow. Not
limiting the mediasize is a compromise between allowing to use Sun
disk label as far as possible and being able to use the entire disk
with another disk label.
This allows to use the full capacity of large IDE disks if they were
not labeled under (Open)Solaris (in both ways of the meaning).
MFC after: 2 weeks
for that argument. This will allow DDB to detect the broad category of
reason why the debugger has been entered, which it can use for the
purposes of deciding which DDB script to run.
Assign approximate why values to all current consumers of the
kdb_enter() interface.
- Introduce per-architecture stack_machdep.c to hold stack_save(9).
- Introduce per-architecture machine/stack.h to capture any common
definitions required between db_trace.c and stack_machdep.c.
- Add new kernel option "options STACK"; we will build in stack(9) if it is
defined, or also if "options DDB" is defined to provide compatibility
with existing users of stack(9).
Add new stack_save_td(9) function, which allows the capture of a stacktrace
of another thread rather than the current thread, which the existing
stack_save(9) was limited to. It requires that the thread be neither
swapped out nor running, which is the responsibility of the consumer to
enforce.
Update stack(9) man page.
Build tested: amd64, arm, i386, ia64, powerpc, sparc64, sun4v
Runtime tested: amd64 (rwatson), arm (cognet), i386 (rwatson)
is required by the X.Org PCI domains code and additionally needs
a workaround for Hummingbird and Sabre bridges as these don't
allow their config headers to be read at any width, which is an
unusual behavior.
- In psycho(4) take advantage of DEFINE_CLASS_0 and use more
appropriate types for some softc members.
MFC after: 3 days
Currently, Giant is not too much contented so that it is ok to treact it
like any other mutexes.
Please don't forget to update your own custom config kernel files.
Approved by: cognet, marcel (maintainers of arches where option is
not enabled at the moment)
include the ithread scheduling step. Without this, a preemption might
occur in between the interrupt getting masked and the ithread getting
scheduled. Since the interrupt handler runs in the context of curthread,
the scheudler might see it as having a such a low priority on a busy system
that it doesn't get to run for a _long_ time, leaving the interrupt stranded
in a disabled state. The only way that the preemption can happen is by
a fast/filter handler triggering a schduling event earlier in the handler,
so this problem can only happen for cases where an interrupt is being
shared by both a fast/filter handler and an ithread handler. Unfortunately,
it seems to be common for this sharing to happen with network and USB
devices, for example. This fixes many of the mysterious TCP session
timeouts and NIC watchdogs that were being reported. Many thanks to Sam
Lefler for getting to the bottom of this problem.
Reviewed by: jhb, jeff, silby
This has the following benefits:
- allows to use the AT keyboard maps in share/syscons/keymaps with
sunkbd(4),
- allows to use kbdmux(4) with sunkbd(4),
- allows Sun RS232 keyboards to be configured and used the same
way as Sun USB keyboards driven by ukbd(4) (which also does AT
keyboard emulation) with X.Org, putting an end to the problem
of native support for the former in X.Org being broken over and
over again.
MFC after: 3 days
First, a file is mmap(2)ed and then mlock(2)ed. Later, it is truncated.
Under "normal" circumstances, i.e., when the file is not mlock(2)ed, the
pages beyond the EOF are unmapped and freed. However, when the file is
mlock(2)ed, the pages beyond the EOF are unmapped but not freed because
they have a non-zero wire count. This can be a mistake. Specifically,
it is a mistake if the sole reason why the pages are wired is because of
wired, managed mappings. Previously, unmapping the pages destroys these
wired, managed mappings, but does not reduce the pages' wire count.
Consequently, when the file is unmapped, the pages are not unwired
because the wired mapping has been destroyed. Moreover, when the vm
object is finally destroyed, the pages are leaked because they are still
wired. The fix is to reduce the pages' wired count by the number of
wired, managed mappings destroyed. To do this, I introduce a new pmap
function pmap_page_wired_mappings() that returns the number of managed
mappings to the given physical page that are wired, and I use this
function in vm_object_page_remove().
Reviewed by: tegge
MFC after: 6 weeks
communicate that it relates to (is called by) thread_alloc()
o Add cpu_thread_free() which is called from thread_free()
to counter-act cpu_thread_alloc().
i386: Have cpu_thread_free() call cpu_thread_clean() to
preserve behaviour.
ia64: Have cpu_thread_free() call mtx_destroy() for the
mutex initialized in cpu_thread_alloc().
PR: ia64/118024
silent NULL pointer dereference in the i386 and sparc64 pmap_pinit()
when the kmem_alloc_nofault() failed to allocate address space. Both
functions now return error instead of panicing or dereferencing NULL.
As consequence, vmspace_exec() and vmspace_unshare() returns the errno
int. struct vmspace arg was added to vm_forkproc() to avoid dealing
with failed allocation when most of the fork1() job is already done.
The kernel stack for the thread is now set up in the thread_alloc(),
that itself may return NULL. Also, allocation of the first process
thread is performed in the fork1() to properly deal with stack
allocation failure. proc_linkup() is separated into proc_linkup()
called from fork1(), and proc_linkup0(), that is used to set up the
kernel process (was known as swapper).
In collaboration with: Peter Holm
Reviewed by: jhb
Blade 1500/SX1500 boards have inherited the firmware bug of the
AX1105 mainboards to not include an interrupt map entry for the
parallel port controller (for the AX1105 the heuristic code for
E450s probably erroneously kicks in and guesses an interrupt).
- Take advantage of bus_generic_setup_intr(9).
- Fix some whitespace bugs.
in the way we implement handling of relocations.
As for the kernel part this fixes the loading of lots of modules,
which failed to load due to unresolvable symbols when built after
the GCC 4.2.0 import. This wasn't due to a change in GCC itself
though but one of several changes in configuration done along the
import. Specfically, HAVE_AS_REGISTER_PSEUDO_OP, which causes GCC
to denote global registers used for scratch purposes and in turn
GAS uses R_SPARC_OLO10 relocations for, is now defined.
While at it replace some more ELF_R_TYPE which should have been
ELF64_R_TYPE_ID but didn't cause problems so far.
- Sync a sanity check between kernel and rtld(1) and change it to be
maintenance free regarding the type used for the lookup table.
- Sprinkle const on lookup tables.
- Use __FBSDID.
Reported and tested by: yongari
MFC after: 5 days
a consequence of sparc64/sparc64/vm_machdep.c revision 1.76. It occurs
when uma_small_free() frees a page. The solution has two parts: (1) Mark
pages allocated with VM_ALLOC_NOOBJ as PG_UNMANAGED. (2) Defer the lock
assertion in pmap_page_is_mapped() until after PG_UNMANAGED is tested.
This is safe because both PG_UNMANAGED and PG_FICTITIOUS are immutable
flags, i.e., they do not change state between the time that a page is
allocated and freed.
Approved by: re (kensmith)
PR: 116794
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
33MHz for calculating the latency timer values for its children.
Inspired by NetBSD doing the same and Linux as well as OpenSolaris
using a similar approach.
While at it rename a variable and change its type to be more
appropriate fuer values of PCI properties so the variable can be
more easily reused.
- Initialize the cache line size register of PCI devices to a
legal value; the cache line size is limited to 64 bytes by the
Fireplane/Safari, JBus and UPA interconnection busses. Setting
it to an unsupported value caused bad performance at least with
GEM as it causes them to not do cache line bursts and to not
issue cache line commands on the PCI bus.
Approved by: re (kensmith)
MFC after: 1 week
ways:
(1) Cached pages are no longer kept in the object's resident page
splay tree and memq. Instead, they are kept in a separate per-object
splay tree of cached pages. However, access to this new per-object
splay tree is synchronized by the _free_ page queues lock, not to be
confused with the heavily contended page queues lock. Consequently, a
cached page can be reclaimed by vm_page_alloc(9) without acquiring the
object's lock or the page queues lock.
This solves a problem independently reported by tegge@ and Isilon.
Specifically, they observed the page daemon consuming a great deal of
CPU time because of pages bouncing back and forth between the cache
queue (PQ_CACHE) and the inactive queue (PQ_INACTIVE). The source of
this problem turned out to be a deadlock avoidance strategy employed
when selecting a cached page to reclaim in vm_page_select_cache().
However, the root cause was really that reclaiming a cached page
required the acquisition of an object lock while the page queues lock
was already held. Thus, this change addresses the problem at its
root, by eliminating the need to acquire the object's lock.
Moreover, keeping cached pages in the object's primary splay tree and
memq was, in effect, optimizing for the uncommon case. Cached pages
are reclaimed far, far more often than they are reactivated. Instead,
this change makes reclamation cheaper, especially in terms of
synchronization overhead, and reactivation more expensive, because
reactivated pages will have to be reentered into the object's primary
splay tree and memq.
(2) Cached pages are now stored alongside free pages in the physical
memory allocator's buddy queues, increasing the likelihood that large
allocations of contiguous physical memory (i.e., superpages) will
succeed.
Finally, as a result of this change long-standing restrictions on when
and where a cached page can be reclaimed and returned by
vm_page_alloc(9) are eliminated. Specifically, calls to
vm_page_alloc(9) specifying VM_ALLOC_INTERRUPT can now reclaim and
return a formerly cached page. Consequently, a call to malloc(9)
specifying M_NOWAIT is less likely to fail.
Discussed with: many over the course of the summer, including jeff@,
Justin Husted @ Isilon, peter@, tegge@
Tested by: an earlier version by kris@
Approved by: re (kensmith)
- p_sflag was mostly protected by PROC_LOCK rather than the PROC_SLOCK or
previously the sched_lock. These bugs have existed for some time.
- Allow swapout to try each thread in a process individually and then
swapin the whole process if any of these fail. This allows us to move
most scheduler related swap flags into td_flags.
- Keep ki_sflag for backwards compat but change all in source tools to
use the new and more correct location of P_INMEM.
Reported by: pho
Reviewed by: attilio, kib
Approved by: re (kensmith)
of pages don't sum to anywhere near the total number of pages on amd64.
This is for the most part because uma_small_alloc() pages have never been
counted as wired pages, like their kmem_malloc() brethren. They should
be. This changes fixes that.
It is no longer necessary for the page queues lock to be held to free
pages allocated by uma_small_alloc(). I removed the acquisition and
release of the page queues lock from uma_small_free() on amd64 and ia64
weeks ago. This patch updates the other architectures that have
uma_small_alloc() and uma_small_free().
Approved by: re (kensmith)
with the INTR_FILTER-enabled MI code. Basically this consists of
registering an interrupt controller (of which there can be multiple
and optionally different ones either per host-to-foo bridge or shared
amongst host-to-foo bridges in any one machine) along with an interrupt
vector as specific argument for all the interrupt vectors used by a
given host-to-foo bridge (roughly similar to registering interrupt
sources on amd64 and i386), providing functions to enable, clear and
disable the interrupts of the children beneath the bridge.
This also includes:
- No longer entering a critical section in tl0_intr() and tl1_intr()
for executing interrupt handlers but rather let the handlers enter
it themselves so in the case of intr_event_handle() we don't enter
a nested critical section.
- Adding infrastructure for binding delivery of interrupt vectors to
specific CPUs which later on can be interfaced with the code from
amd64/i386 for binding interrupts to specific CPUs.
- Getting rid of the wrapper hack introduced along the lines of the
API changes for INTR_FILTER which as a side-effect caused interrupts
associated with ithread handlers only to get the elevated priority
of those associated with filters ("fast handlers") (this removes the
hack also in the non-INTR_FILTER case).
- Disabling (by not clearing) an interrupt in the interrupt controller
until all associated handlers have been executed, which is crucial
for the typical locking strategy of NIC drivers in order to work
correctly in case of shared interrupts. This was a more or less
theoretical problem on sparc64 though, as shared interrupts are
rather uncommon there except for the on-board SCCs and UARTs.
Note that due to the behavior of at least of some of the interrupt
controllers used on sparc64 an enable+EOI instead of a disable+EOI
approach (as implied by the INTR_FILTER MI code and implemented on
other architectures) is used as the latter can cause lost interrupts
or in the worst case interrupt starvation.
o Correct a typo in sbus_alloc_resource() which caused (pass-through)
allocations to only work down to the grandchildren of the bus, which
wasn't a real problem so far as we don't support any devices which are
great-grandchildren or greater of a U2S bridge, yet.
o In fhc(4) use bus_{read,write}_4() instead of bus_space_{read,write}_4()
in order to get rid of sc_bh and sc_bt in the fhc_softc. Also get rid
of some other unneeded members in fhc_softc.
Reviewed by: marcel (earlier version)
Approved by: re (kensmith)
instead of per IOMMU, so we no longer need to program all of them
identically in systems having multiple IOMMUs. This continues the
rototilling of the nexus(4) done about 5 months ago, which amongst
others changed nexus(4) and the drivers for host-to-foo bridges
to provide bus_get_dma_tag methods, allowing to handle DMA tags in
a hierarchical way and to link them with devices.
This still doesn't move the silicon bug workarounds for Sabre (and
in the uncommitted schizo(4) for Tomatillo) bridges into special
bus_dma_tag_create() and bus_dmamap_sync() methods though, as w/o
fully newbus'ified bus_dma_tag_create() and bus_dma_tag_destroy()
this still requires too much hackery, i.e. per-child parent DMA
tags in the parent driver.
- Let the host-to-foo drivers supply the maximum physical address
of the IOMMU accompanying the bridges. Previously iommu(4) hard-
coded an upper limit of 16GB, which actually only applies to the
IOMMUs of the Hummingbird and Sabre bridges. The Psycho variants
as well as the U2S in fact can can translate to up to 2TB, i.e.
translate to 41-bit physical addresses. According to the recently
available Tomatillo documentation these bridges even translate to
43-bit physical addresses and hints at the Schizo bridges doing
43 bits as well.
This fixes the issue the FreeBSD 6.0 todo list item "Max RAM on
sparc64" was refering to and pretty much obsoletes the lack of
support for bounce buffers on sparc64.
Thanks to Nathan Whitehorn for pointing me at the Tomatillo manual.
Approved by: re (kensmith)
print a one line error message. Add some comments on not being able to
trust the day of week field (I'll act on these comments in a follow up
commit).
Approved by: re
MFC after: 3 weeks
new code and third party modules which try to depend on it.
- Initialize sched_lock in sched_4bsd.c.
- Declare sched_lock in sparc64 pmap.c and assert that we're compiling
with SCHED_4BSD to prevent accidental crashes from running ULE. This
is the sole remaining file outside of the scheduler that uses the
global sched_lock.
Approved by: re
allowing the driver for the host-PCI-bridge to indicate that
reenumeration of the PCI busses isn't supported by returning
-1 instead of a valid PCI bus number. This is needed in order
support both Tomatillo, which don't support reenumeration and
thus are apparently intended to be used for independently
numbered PCI domains only, and Psycho bridges, whose busses
need to be reenumerated on at least some E450, without the
#ifndef currently used for sun4v in order to support multiple
independently PCI domains. The actual allocation/incrementation
of the PCI bus numbers is now done in psycho(4), though it
no longer establish a mapping between bus numbers and device
nodes like ofw_pci_alloc_busno() did as that functionality
wasn't used (but can easily brought back if really needed).
The now no longer used sys/sparc64/pci/ofw_pci.c is also
removed from sys/conf/files.sun4v as ofw_pci_alloc_busno()
wasn't used there in the first place.
- In ofw_pci_default_{adjust_busrange,intr_pending}() sanity
check that the device has a parent before passing it on.
- Make psycho_softcs static to sys/sparc64/pci/psycho.c as
it's not used outside of that module.
- In sys/sparc64/pci/ofw_pcib_subr.c remove the superfluous
inclusion of opt_global.h and correct the debug output for
adjusting the subordinate bus number.
instead of using the PCI bus number, like it's already done for
sun4v in order to deal properly with independently numbered PCI
domains which can't be reenumerated (in the case of sun4u f.e.
Tomatillo bridges). For machines where we need to reenumerate
all PCI busses this change obviously introduces the theoretical
cosmetic problem that the device number of the PCI bus no longer
equals to its PCI bus number. In practice this doesn't happen
as both are assigned linearly and in parallel.
handlers as filter/"fast" handlers so shutdown_nice() can
acquire the process lock.
- Use bus_{read,write}_8() instead of bus_space_{read,write}_8()
in order to get rid of sc_bushandle and sc_bustag in the softc.
- Remove the banal and outdated comment above sbus_filter_stub().
allowing it to be a filter/"fast" handler. Locking the interrupt
handlers with a spin lock is mainly a requirement in schizo(4)
but as we ought to register the spin lock anyway it should not
hurt to take advantage of it in psycho(4).
- Pass both a driver_filter_t and a driver_intr_t argument to
psycho_set_intr(), allowing to get rid of the FAST interrupt
flag hack.
- Don't register the over-temperature interrupt handler as filter/
"fast" handler so shutdown_nice() can acquire the process lock.
- Use bus_{read,write}_8() instead of bus_space_{read,write}_8()
in order to get rid of sc_bushandle and sc_bustag in the softc.
- Correct the debug output for adjusting the subordinate bus number.
- Remove the banal and outdated above psycho_filter_stub().
- Fix some white space nits.
These CPUs use an enhanced layout of the interrupt vector dispatch
and dispatch status registers in order to allow sending IPIs to
multiple targets simultaneously. Thus support for these CPUs was
put in a newly added cheetah_ipi_selected(). This is intended to
be pointed to by cpu_ipi_selected, which now is a function pointer,
in order to avoid cpu_impl checks once booted. Alternatively it
can point to spitfire_ipi_selected(), which was renamed from
cpu_ipi_selected(). Consequently cpu_ipi_send() was also renamed
to spitfire_ipi_send() (there's no need for a cheetah equivalent
of this so far). Initialization of the cpu_ipi_selected pointer
and other requirements is done in mp_init(), which was renamed
from mp_tramp_alloc(), as cpu_mp_start() isn't called on UP
systems while cpu_ipi_selected() is. As a side-effect this allows
to make mp_tramp static to sys/sparc64/sparc64/mp_machdep.c.
For the sake of avoiding #ifdef SMP and for keeping the history in
place cheetah_ipi_selected() and spitfire_ipi_{selected,send}()
where not put into/moved to sys/sparc64/sparc64/{cheetah,spitfire}.c
- Add some CTASSERTs and KASSERTs ensuring that MAXCPU doesn't
exceed the data types we use to store the CPU bit fields or the
number of USIII and greater CPUs supported by the current
cheetah_ipi_selected() implementation (which for JBus-CPUs is
only 4; that should be fine though as according to OpenSolaris
there are no sun4u machines with more than 4 JBus-CPUs).
- In cpu_mp_start() don't enumerate and start more than MAXCPU CPUs
as we can't handle more than that.
- In cpu_mp_start() check for upa-portid vs. portid depending on
cpu_impl for consistency with nexus(4).
- In spitfire_ipi_selected() add KASSERTs ensuring that a CPU isn't
told to IPI itself as sun4u CPUs just can't do that.
- In spitfire_ipi_send() do a MEMBAR #Sync after writing the
interrupt vector data as we want to make sure the payload was
actually written before we trigger the dispatch.
- In spitfire_ipi_send() also verify IDR_BUSY when checking whether
the dispatch was successful as it has to be cleared for this to
be the case.
- Remove some redundant variables.
RTC function of a National Semiconductor PC87317/PC97317. This
consists of using the century register the same way Solaris does
for compatibility reasons. Once there is a MD power(4) we'd also
want to interface the APC (Advanced Power Control) functionality
of the same chip function with it.
- Use a macro for the device description and take advantage of
ISA_PNP_PROBE() setting the device description.
- Use the generated typedefs for the prototypes of the device
interface functions.
reasons outlined in the comment removed along with it, because the
OFW hostid has no real meaning for FreeBSD and mainly so the OFW
hostid is not confused with the FreeBSD hostid.
more exposure. The current state of SCTP implementation is
considered to be ready for 32-bit platforms, but still need some
work/testing on 64-bit platforms.
Approved by: re (kensmith)
Discussed with: rrs
making the relevant files standard. This avoids duplication and
makes it easier to override/disable unwanted schemes. Since ARM
doesn't have a DEFAULTS configuration file, leave the source
files for the BSD and MBR partitioning schemes in files.arm for
now.
caches with data caches after writing to memory. This typically
is required to make breakpoints work on ia64 and powerpc. For
those architectures the function is implemented.
- Use sched_throw() rather than replicating the same cpu_throw() code for
each architecture. This also allows the scheduler to use any locking it
may want to.
- Use the thread_lock() rather than sched_lock when preempting.
- The scheduler lock is not required to synchronize release_aps.
Tested by: kris, current@
Tested on: i386, amd64, ULE, 4BSD, libthr, libkse, PREEMPTION, etc.
Discussed with: kris, attilio, kmacy, jhb, julian, bde (small parts each)
- Rename PCPU_LAZY_INC into PCPU_INC
- Add the PCPU_ADD interface which just does an add on the pcpu member
given a specific value.
Note that for most architectures PCPU_INC and PCPU_ADD are not safe.
This is a point that needs some discussions/work in the next days.
Reviewed by: alc, bde
Approved by: jeff (mentor)
Probabilly, a general approach is not the better solution here, so we should
solve the sched_lock protection problems separately.
Requested by: alc
Approved by: jeff (mentor)
handler is wrapped in a couple of functions - a filter wrapper and an
ithread wrapper. In this case (and just in this case), the filter
wrapper could ask the system to schedule the ithread and mask the
interrupt source if the wrapped handler is composed of just an ithread
handler: modify the "old" interrupt code to make it support
this situation, while the "new" interrupt code is already ok.
Discussed with: jhb
used to return PAGE_SIZE without respect to restrictions of a DMA tag.
This affected all of the busdma load functions that use
_bus_dmamap_loader_buffer() as their back-end.
Reviewed by: scottl
Note on dcons:
To enable dcons in kernel, put the following lines in /boot/loader.conf.
You may also want to enable dcons in /etc/ttys.
boot_multicons="YES"
#Force dcons to be the high-level console if a firewire bus presents.
#hw.firewire.dcons_crom.force_console=1
FireWire/dcons support in loader will come shortly.
(i386/amd64 only)
same way it was enabled for Linux binares in linuxulator.
This allows binaries built with -pie. Many ports auto-detect -fPIE support
in GCC 4.2 and build binaries FreeBSD was unable to run.
referenced outside of mp_machdep.c
- Replace a magic 14 with the newly added IDC_ITID_SHIFT macro.
- Remove the global mp_boot_mid variable as it's not really necessary
and just replacing it with PCPU_GET(mid) doesn't have any impact on
performance once booted.
- Replace PCPU_GET(cpuid) with the curcpu shortcut.
- Replace hardcoded function names in panic strings etc with __func__
so they don't need to be updated when renaming the function.
- Use register_t instead of u_long for variables used to hold the
return value of intr_disable() so we don't need to apply any
knowledge about the actual width of that value here.
- Improve the wording of some comments.
- Fix several style(9) bugs.
- Use __FBSDID in identcpu.c.
- Remove #ifndef SUN4V around global cpu_impl variable; it doesn't
hurt on sun4v for now and once setPQL2() is gone sun4v can stop
sharing identcpu.c with sparc64, making the reminder of this file
also sparc64-only again. [1]
Submitted by: kmacy [1]
iommureg.h (which already began to bitrot) and iommuvar.h from the
sun4v source and adjust some of the source which is shared between
sparc64 and sun4v as appropriate.
vmcnts. This can be used to abstract away pcpu details but also changes
to use atomics for all counters now. This means sched lock is no longer
responsible for protecting counts in the switch routines.
Contributed by: Attilio Rao <attilio@FreeBSD.org>
