o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
(4 in operation), 4GB ram (3.5 usable) ARM machine.
Support covers device drivers for:
- Serial Peripheral Interface (SPI)
- Chrome Embedded Controller (EC) - SPI-based version
- XHCI and USB 3.0 dual-role device PHY
Also:
- Add support for Exynos5420 in Pad module
- Move power-related functions to separate driver --
Power Management Unit (PMU)
- Enable XHCI for Chromebook1
Special thanks to grehan@ for hardware, and to
hselasky@ for r269139.
that it can connect to switches at speeds other than 1gb.
This requires changing the reference clock speed. Since we still don't
have a general clock API that lets a SoC-independant driver manipulate its
own clocks, this change includes a weak reference to a routine named
cgem_set_ref_clk(). The default implementation is a no-op; SoC-specific
code can provide an implementation that actually changes the speed.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
o Allow setting keymap in FDT, use hardcoded one by default
o Represent fallback keymap as a list rather than directly usable M*N array
Submitted by: Maxim Ignatenko <gelraen.ua@gmail.com>
current RADXA config. Radxa Rock (RR) boards have few types such as
RR (full version), RR Lite and some variants of RR engineering samples.
Add kernel config and FDT file for RR Lite board.
Approved by: stas (mentor)
Adjust the exynos and zedboard dts files to use max-frequency (the
documented standard property) instead of clock-frequency.
Submitted by: Thomas Skibo <ThomasSkibo@sbcglobal.net>
- Don't allow high-speed mode on OMAP4 due to hardware erratum.
- Check the proper bit in the status register when waiting for the
controller to come out of reset.
- Add handling for the "non-removable" fdt property by always returning
"card is present" status.
- Add the non-removable property for the MMC card on a Beaglebone Black.
- Add the non-removable property for Pandaboard as a workaround.
For Pandaboard the card detect pin is handled by the twl6030 fpga device
which gets an interrupt on pin change and then has to query the fpga
for the actual status. We don't have code to do that yet.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
We don't know our ARM security state, so one of them will operate.
- Don't set frequency, since it's unpossible in non-secure state.
Only rely on DTS clock-frequency value or get clock from timer.
Discussed with: ian, cognet
Support covers device drivers for:
- Interrupt Combiner
- gpio/pad, External Interrupts Controller (pad)
- I2C Interface
- Chrome Embedded Controller
- Chrome Keyboard
Also:
- Use new gpio dev class in EHCI driver
- Expand device tree information
