On arm64 PCI config memory is expected to be mapped with a non-posted
device type. To handle this use the new bus_map_resource support in
arm64 to map memory with the new VM_MEMATTR_DEVICE_NP attribute. This
memory has already been allocated and activated, it just needs to be
mapped.
Reviewed by: kevans, mmel
Differential Revision: https://reviews.freebsd.org/D30079
Now that the upper layers all go through a layer to tie into these
information functions that translates an sbuf into char * and len. The
current interface suffers issues of what to do in cases of truncation,
etc. Instead, migrate all these functions to using struct sbuf and these
issues go away. The caller is also in charge of any memory allocation
and/or expansion that's needed during this process.
Create a bus_generic_child_{pnpinfo,location} and make it default. It
just returns success. This is for those busses that have no information
for these items. Migrate the now-empty routines to using this as
appropriate.
Document these new interfaces with man pages, and oversight from before.
Reviewed by: jhb, bcr
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D29937
It's a class0 driver that implements some pcib methods and creates
a pci bus as its children.
The "ofw_pci" name will be used by a new driver that will be a subclass
of the pci bus.
No functional changes intended.
Submitted by: Kornel Duleba <mindal@semihalf.com>
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Alstom Group
Differential Revision: https://reviews.freebsd.org/D30226
Name each pcib driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/pcib from kernel; already loaded from kernel
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
tightening constraints on busy as a precursor to lockless page lookup and
should largely be a NOP for these cases.
Reviewed by: alc, kib, markj
Differential Revision: https://reviews.freebsd.org/D22611
There are several mechanisms by which a vm_page reference is held,
preventing the page from being freed back to the page allocator. In
particular, holding the page's object lock is sufficient to prevent the
page from being freed; holding the busy lock or a wiring is sufficent as
well. These references are protected by the page lock, which must
therefore be acquired for many per-page operations. This results in
false sharing since the page locks are external to the vm_page
structures themselves and each lock protects multiple structures.
Transition to using an atomically updated per-page reference counter.
The object's reference is counted using a flag bit in the counter. A
second flag bit is used to atomically block new references via
pmap_extract_and_hold() while removing managed mappings of a page.
Thus, the reference count of a page is guaranteed not to increase if the
page is unbusied, unmapped, and the object's write lock is held. As
a consequence of this, the page lock no longer protects a page's
identity; operations which move pages between objects are now
synchronized solely by the objects' locks.
The vm_page_wire() and vm_page_unwire() KPIs are changed. The former
requires that either the object lock or the busy lock is held. The
latter no longer has a return value and may free the page if it releases
the last reference to that page. vm_page_unwire_noq() behaves the same
as before; the caller is responsible for checking its return value and
freeing or enqueuing the page as appropriate. vm_page_wire_mapped() is
introduced for use in pmap_extract_and_hold(). It fails if the page is
concurrently being unmapped, typically triggering a fallback to the
fault handler. vm_page_wire() no longer requires the page lock and
vm_page_unwire() now internally acquires the page lock when releasing
the last wiring of a page (since the page lock still protects a page's
queue state). In particular, synchronization details are no longer
leaked into the caller.
The change excises the page lock from several frequently executed code
paths. In particular, vm_object_terminate() no longer bounces between
page locks as it releases an object's pages, and direct I/O and
sendfile(SF_NOCACHE) completions no longer require the page lock. In
these latter cases we now get linear scalability in the common scenario
where different threads are operating on different files.
__FreeBSD_version is bumped. The DRM ports have been updated to
accomodate the KPI changes.
Reviewed by: jeff (earlier version)
Tested by: gallatin (earlier version), pho
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20486
These calls are not the same in general: the former will dequeue the
page if it is enqueued, while the latter will just leave it alone. But,
all existing uses of the former apply to unmanaged pages, which are
never enqueued in the first place. No functional change intended.
Reviewed by: kib
MFC after: 1 week
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20470
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
front-end doesn't support SDMA or the latter implements a platform-
specific transfer method instead. While at it, factor out allocation
and freeing of SDMA resources to sdhci_dma_{alloc,free}() in order to
keep the code more readable when adding support for ADMA variants.
o Base the size of the SDMA bounce buffer on MAXPHYS up to the maximum
of 512 KiB instead of using a fixed 4-KiB-buffer. With the default
MAXPHYS of 128 KiB and depending on the controller and medium, this
reduces the number of SDHCI interrupts by a factor of ~16 to ~32 on
sequential reads while an increase of throughput of up to ~84 % was
seen.
Front-ends for broken controllers that only support an SDMA buffer
boundary of a specific size may set SDHCI_QUIRK_BROKEN_SDMA_BOUNDARY
and supply a size via struct sdhci_slot. According to Linux, only
Qualcomm MSM-type SDHCI controllers are affected by this, though.
Requested by: Shreyank Amartya (unconditional bump to 512 KiB)
o Introduce a SDHCI_DEPEND macro for specifying the dependency of the
front-end modules on the sdhci(4) one and bump the module version
of sdhci(4) to 2 via an also newly introduced SDHCI_VERSION in order
to ensure that all components are in sync WRT struct sdhci_slot.
o In sdhci(4):
- Make pointers const were applicable,
- replace a few device_printf(9) calls with slot_printf() for
consistency, and
- sync some local functions with their prototypes WRT static.
Fix the build of the GENERIC-MMCCAM kernel config after the sdhci_xenon
driver was commited.
While here correct sdhci_fdt and tegra_sdhci, even with MMCCAM they do
need to depend on sdhci(4)
Reported by: Reshetnikov Dmitriy <genserg@hotmail.com>
Approved by: re (kib)
Sponsored by: Rubicon Communications, LLC ("NetGate")
error in the function hypercall_memfree(), where the wrong arena was being
passed to kmem_free().
Introduce a per-page flag, VPO_KMEM_EXEC, to mark physical pages that are
mapped in kmem with execute permissions. Use this flag to determine which
arena the kmem virtual addresses are returned to.
Eliminate UMA_SLAB_KRWX. The introduction of VPO_KMEM_EXEC makes it
redundant.
Update the nearby comment for UMA_SLAB_KERNEL.
Reviewed by: kib, markj
Discussed with: jeff
Approved by: re (marius)
Differential Revision: https://reviews.freebsd.org/D16845
This is an amalgam of a patch by Doug Ambrisko to
generalize uart_acpi_find_device, imp moving the
ACPI table to uart_dev_ns8250.c and advice by jhb
to work around a bug in the EPYC 3151 BIOS
(the BIOS incorrectly marks the serial ports as
disabled)
Reviewed by: imp
MFC after: 8 weeks
Differential Revision: https://reviews.freebsd.org/D16432
Change OF_getencprop_alloc semantics to be combination of malloc and
OF_getencprop and return size of the property, not number of elements
allocated.
For the use cases where number of elements is preferred introduce
OF_getencprop_alloc_multi helper function that copies semantics
of OF_getencprop_alloc prior to this change.
This is to make OF_getencprop_alloc and OF_getencprop_alloc_multi
function signatures consistent with OF_getencprop_alloc and
OF_getencprop_alloc_multi.
Functionality-wise this patch is mostly rename of OF_getencprop_alloc
to OF_getencprop_alloc_multi except two calls in ofw_bus_setup_iinfo
where 1 was used as a block size.
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
Make vm_wait() take the vm_object argument which specifies the domain
set to wait for the min condition pass. If there is no object
associated with the wait, use curthread' policy domainset. The
mechanics of the wait in vm_wait() and vm_wait_domain() is supplied by
the new helper vm_wait_doms(), which directly takes the bitmask of the
domains to wait for passing min condition.
Eliminate pagedaemon_wait(). vm_domain_clear() handles the same
operations.
Eliminate VM_WAIT and VM_WAITPFAULT macros, the direct functions calls
are enough.
Eliminate several control state variables from vm_domain, unneeded
after the vm_wait() conversion.
Scetched and reviewed by: jeff
Tested by: pho
Sponsored by: The FreeBSD Foundation, Mellanox Technologies
Differential revision: https://reviews.freebsd.org/D14384
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
files that can use the default value.
It used to be required that the low-order bits of KERNVIRTADDR matched
the low-order bits of the physical load address for all arm platforms.
That hasn't been a requirement for armv6 platforms since FreeBSD 10.
There is no longer any relationship between load addr and KERNVIRTADDR
except that both must be aligned to a 2 MiB boundary.
This change makes the default KERNVIRTADDR value 0xc0000000, and removes the
options from all the platforms that can use the default value. The default
is now defined in vmparam.h, and that file is now included in a few new
places that reference KERNVIRTADDR, since it may not come in via the
forced-include of opt_global.h on the compile command line.
Transition all boards that support arm cortex CPUs to armv7. This
leaves two armv6 kernels in the tree. RPI-B, which uses the BCM2835
which has a ARM1176 core, and VERSATILEPB, which is a qemu board setup
around the time RPI-B went in. Copy std.armv6 to std.armv7, even
though that duplicates a lot of stuff. More work needs to be done to
sort out the duplication.
Differential Revision: https://reviews.freebsd.org/D12027
