When the ENA_FLAG_DEVICE_RUNNING flag is disabled, the AENQ handlers
aren't executed. To fix that, the watchdog timestamp should be updated
just before enabling the watchdog.
Timer service was always being enabled, even if the device wasn't up
before the reset. That shouldn't happen, as the timer service is being
executed only for working interface.
Differential Revision: https://reviews.freebsd.org/D21932
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
As the pmamp_change_attr() is public on arm64 since r351131, it can be
used on the arm64 to map memory range as with the write combined
attribute.
It requires the driver to use generic VM_MEMATTR_WRITE_COMBINING flag
instead of the x86 specific PAT_WRITE_COMBINING.
Differential Revision: https://reviews.freebsd.org/D21931
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Altough in the comment above the pmap_change_attr() it was mentioned
that VA could be in KV or DMAP memory space. However,
pmap_change_attr_locked() was accepting only the values inside the DMAP
memory range.
To fix that, the condition check was changed so also the va inside the
KV memory range would be accepted.
The sample use case that wasn't supported is the PCI Device that has the
BAR which should me mapped with the Write Combine attribute - for
example BAR2 of the ENA network controller on the A1 instances on AWS.
Tested on A1 AWS instance and changed ENA BAR2 mapped resource to be
write-combined memory region.
Differential Revision: https://reviews.freebsd.org/D22055
MFC after: 2 weeks
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
There was a couple issues with GDB machdep code for PPC/PPC64, the main ones being:
- wrong register sizes being returned
- pcb_context index was wrong (this affects all PPC variants)
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D22201
In some scenarios, the 4K trapstk may overflow, corrupting tmpstk.
This was observed during remote debugging, with the following steps:
At remote host (R):
- enter kdb during boot
- switch to gdb backend
At local host (L):
- attach gdb to R
- try to read an invalid memory position
At R:
- a DSI trap occurs and kdb restarts (all this occurs on trapstk)
- while printing the stacktrace, trapstk overflows and corrupts tmpstk
Reviewed by: jhibbits
Differential Revision: https://reviews.freebsd.org/D22200
First, SCL low timeout is set to 25 milliseconds by default as opposed
to 1 millisecond before. The new value is based on the SMBus
specification. The timeout can be changed on a per bus basis using
dev.iicbb.N.scl_low_timeout sysctl.
The driver uses DELAY to wait for high SCL up to 1 millisecond, then it
switches to pause_sbt(SBT_1MS) for the rest of the timeout.
While here I made a number of other changes. 'udelay' that's used for
timing clock and data signals is now calculated based on the requested
bus frequency (dev.iicbus.N.frequency) instead of being hardcoded to 10
microseconds. The calculations are done in such a fashion that the
default bus frequency of 100000 is converted to udelay of 10 us. This
is for backward compatibility. The actual frequency will be less than a
quarter (I think) of the requested frequency.
Also, I added detection of stuck low SCL in a few places. Previously,
the code would just carry on after the SCL low timeout and that might
potentially lead to misinterpreted bits.
Finally, I fixed several style issues near the code that I changed.
Many more are still remaining.
Tested by accessing HTU21 temperature and humidity sensor in this setup:
superio0: <Nuvoton NCT5104D/NCT6102D/NCT6106D (rev. B+)> at port 0x2e-0x2f on isa0
gpio1: <Nuvoton GPIO controller> at GPIO ldn 0x07 on superio0
pcib0: allocated type 4 (0x220-0x226) for rid 0 of gpio1
gpiobus1: <GPIO bus> on gpio1
gpioiic0: <GPIO I2C bit-banging driver> at pins 14-15 on gpiobus1
gpioiic0: SCL pin: 14, SDA pin: 15
iicbb0: <I2C bit-banging driver> on gpioiic0
iicbus0: <Philips I2C bus> on iicbb0 master-only
iic0: <I2C generic I/O> on iicbus0
Discussed with: ian, imp
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D22109
From Jake:
The iflib stack failed to release all of the memory allocated under
M_IFLIB during device detach.
Specifically, the ifmp_ring, the ift_ifdi Tx DMA info, and the ifr_ifdi Rx
DMA info were not being released.
Release this memory so that iflib won't leak memory when a device
detaches.
Since we're freeing the ift_ifdi pointer during iflib_txq_destroy we
need to call this only after iflib_dma_free in iflib_tx_structures_free.
Additionally, also ensure that we destroy the callout mutex associated
with each Tx queue when we free it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: erj@, gallatin@
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D22157
Using cam_sim_alloc_dev() allows to properly set sim_dev field so that
sdiob(4) can attach to the CAM device that represents SDIO card.
The same change for SDHCI driver happened in r348800.
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D22192
This is in preparation for adding the corresponding support to iwm(4).
Version 46 is the latest but contains unrecognized TLVs, so use version
43 for now.
Obtained from: linux-firmware
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Arm64 allows us to create execute only mappings. To make sure userspace is
unable to accidentally execute kernel code set the user execute never
bit in the kernel page tables.
MFC after: 1 week
Sponsored by: DARPA, AFRL
r351049 bogusly deleted these lines from files.amd64 but failed to add them to
files.x86. Since this works on i386, add them to files.x86 rather than just
adding them back to files.amd64.
PR: 240734
Reported by: Michael Pro
Summary:
ARM64 currently treats all data abort exceptions as page faults. This
can cause infinite loops on non-page fault faults, such as alignment faults.
Since kernel-side alignment faults should be avoided, this adds support directly
to the el0 fault handler, instead of the data_abort() handler.
Test Plan: Tested on rpi3, with a misaligned ldm test.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D22133
I limited potentially infinite timings by 960 us based on a footnote on
page 38 of Maxim Integrated Application Note 937, Book of iButton
Standards: "In order not to mask interrupt signalling by other devices
on the 1–Wire bus, tRSTL + tR should always be less than 960 us."
MFC after: 3 weeks
Previously we used the minimal value of 1 us and it was really tight.
Application Note 3829 has a table describing recommended t_rec values
for various bus voltages, temperature conditions and numbers of slave
devices. The new value decreases the maximum possible data rate from
16.3 Kbit/s to 13.3 Kbit/s, but it allows for up to four slaves on a
3.3V bus (under room temperature).
References:
- Maxim Integrated Application Note 3829
Determining the Recovery Time for Multiple-Slave 1-Wire(R) Networks
- Maxim Integrated Application Note 937
Book of iButton Standards
Discussed with: imp (D22108)
MFC after: 3 weeks
We may want to mask exceptions when in userspace. This was previously
impossible as threads are created with all exceptions unmasked and
signals expected userspace to mask any. Fix these by copying the
mask state on thread creation and allow exceptions to be masked on
signal return, as long as they don't change.
Sponsored by: DARPA, AFRL
To allow consistent values to be used in both the kernel and userspace
create a function for these to be read from the kernel. They use a newly
created macro with the name of the ID register to read. For now there is
redundant information in the user_regs array as it still holds the CRm and
Op2 values, however this will be fixed in a later change.
This will be used by ptrace to allow hardware breakpoints in userspace.
Sponsored by: DARPA, AFRL
These instructions are used to access the registers described in armreg.h,
and will be used in a future change to create a per-register identification
macro.
Sponsored by: DARPA, AFRL
The debug monitor register state is now stored in a struct and updated
when required. Currently there is only a kernel state, however a
per-process state will be added in a future change.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22128
Previously we would call data_abort on all data and instruction aborts
however this is incorrect for most abort types. Move to use an array
of function pointers to allow for more handlers to be easily added.
Reviewed by: jhibbits
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D22170
Because of the previous naming scheme the old ID_AA64PFR0_EL1 macro
collided with a potential macro for the register of the same name. To fix
this collision rename these macros.
Sponsored by: DARPA, AFRL
The previous code came from OpenSolaris, which in my understanding require
allocation size to be known to free memory. To store that size previous
code allocated additional 8 byte header. But I have noticed that zlib
with present settings allocates 64KB context buffers for each call, that
could be efficiently cached by UMA, but addition of those 8 bytes makes
them fall back to physical RAM allocations, that cause huge overhead and
lock congestion on small blocks. Since FreeBSD's free() does not have
the size argument, switching to it solves the problem, increasing write
speed to ZVOLs with 4KB block size and GZIP compression on my 40-threads
test system from ~60MB/s to ~600MB/s.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
flag and use the same system.
This enables further fault locking improvements by allowing more faults to
proceed with a shared lock.
Reviewed by: kib
Tested by: pho
Differential Revision: https://reviews.freebsd.org/D22116
Certain consumers still need to guarantee a stable reference so we can not
switch entirely to atomics yet. Exclusive lock holders can still modify
and examine the refcount without using the ref api.
Reviewed by: kib
Tested by: pho
Sponsored by: Netflix, Intel
Differential Revision: https://reviews.freebsd.org/D21598
Recent changes to busy/valid/dirty have enabled page based synchronization
and the object lock is no longer required in many cases.
Reviewed by: kib
Sponsored by: Netflix, Intel
Differential Revision: https://reviews.freebsd.org/D21597
Declare retry in the function scope.
Rename it to retry as there is a timeout function which was
causing to code to compile.
Reported by: jhibbits
MFC after: 1 month
X-MFC-WITH: r354089
and IPv6. With IPv6 we may call if_addmulti() in context of processing
of an incoming packet. Usually this is interrupt context. While most
of the NIC drivers are able to reprogram multicast filters without
sleeping, some of them can't. An example is e1000 family of drivers.
With iflib conversion the problem was somewhat hidden. Iflib processes
packets in private taskqueue, so going to sleep doesn't trigger an
assertion. However, the sleep would block operation of the driver and
following incoming packets would fill the ring and eventually would
start being dropped. Enabling epoch for the full time of a packet
processing again started to trigger assertions for e1000.
Fix this problem once and for all using a general taskqueue to call
if_ioctl() method in all cases when if_addmulti() is called in a
non sleeping context. Note that nobody cares about returned value.
Reviewed by: hselasky, kib
Differential Revision: https://reviews.freebsd.org/D22154
Epoch itself doesn't rely on the counter and it is provided
merely for sleeping subsystems to check it.
- In functions that sleep use THREAD_CAN_SLEEP() to assert
correctness. With EPOCH_TRACE compiled print epoch info.
- _sleep() was a wrong place to put the assertion for epoch,
right place is sleepq_add(), as there ways to call the
latter bypassing _sleep().
- Do not increase td_no_sleeping in non-preemptible epochs.
The critical section would trigger all possible safeguards,
no sleeping counter is extraneous.
Reviewed by: kib
After r353292, netmap generic adapter on if_vlan interfaces panics on
asserting the NET_EPOCH. In more detail, this happens when
nm_os_generic_xmit_frame() is called, that is in the generic txsync
routine.
Fix the issue by entering the NET_EPOCH during the generic txsync.
We amortize the cost of entering/exiting over a whole batch of
transmissions.
PR: 241489
Reported by: Aleksandr Fedorov <aleksandr.fedorov@itglobal.com>
This patch modifies the zfs_ioc_snapshot_list_next() ioctl to enable it
to take input parameters that alter the way looping through the list of
snapshots is performed. The idea here is to restrict functions that
throw away some of the snapshots returned by the ioctl to a range of
snapshots that these functions actually use. This improves efficiency
and execution speed for some rollback and send operations.
Reviewed-by: Tom Caputi <tcaputi@datto.com>
Reviewed-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Signed-off-by: Alek Pinchuk <apinchuk@datto.com>
Closes#8077zfsonlinux/zfs@4c0883fb4a
MFC after: 2 weeks
