The on-chip SD slots do not have PCI BARs corresponding to them, so
this has to be handled in the custom SoC memory allocation.
Provide memory resource for rids corresponding to BAR 0 and 1 in
the custom allocation code.
The XLP on-chip devices have PCI configuration headers, but some of the
devices need custom resource allocation code.
- devices with no MEM/IO BARs with registers in PCIe extended reg
space have to be handled in memory resource allocation
- devices without INTPIN/INTLINE in PCI header can be supported
by having these faked with a shadow register.
- Some devices does not allow 8/16 bit access to the register space,
he default bus space cannot be used for these.
Subclass pci and override attach and resource allocation methods to
take care of this.
Remove earlier code which did this partially.
Temporarily revert an upstream commit. This change caused regressions for
too many laptop users. Especially, automatic repair for broken _BIF caused
strange reference counting issues and kernal panics. This reverts:
c995fed15a
SCTP will only do IPv4 UDP checksum calculation as defined by the host
policy. When tunneling SCTP always calculates the inner checksum already
so not doing the outer UDP can save cycles.
While here virtualize the variable.
Requested by: tuexen
MFC after: 2 weeks
The flash commands and responses are little-endian and have to be
byte swapped on big-endian systems. However the raw read of data
need not be swapped.
Make the cfi_read and cfi_write do the swapping, and provide a
cfi_read_raw which does not byte swap for reading data from
flash.
loaded and unloaded, also have sdt.ko register callbacks with kern_sdt.c
that will be called when a newly loaded KLD module adds more probes or
a module with probes is unloaded.
This fixes two issues: first, if a module with SDT probes was loaded after
sdt.ko was loaded, those new probes would not be available in DTrace.
Second, if a module with SDT probes was unloaded while sdt.ko was loaded,
the kernel would panic the next time DTrace had cause to try and do
anything with the no-longer-existent probes.
This makes it possible to create SDT probes in KLD modules, although there
are still two caveats: first, any SDT probes in a KLD module must be part
of a DTrace provider that is defined in that module. At present DTrace
only destroys probes when the provider is destroyed, so you can still
panic the system if a KLD module creates new probes in a provider from a
different module(including the kernel) and then unload the the first module.
Second, the system will panic if you unload a module containing SDT probes
while there is an active D script that has enabled those probes.
MFC after: 1 month
too many laptop users. Especially, automatic repair for broken _BIF caused
strange reference counting issues and kernal panics. This reverts:
c995fed15a
Move XLP PCI UART device to sys/mips/nlm/dev/ directory. Other
drivers for the XLP SoC devices will be added here as well.
Update uart_cpu_xlp.c and uart_pci_xlp.c use macros for uart port,
speed and IO frequency.
for the same object. This can happen when object is a dependency of the
dlopen()ed dso. When called several times, we waste time due to unneeded
processing, and memory, because obj->vertab is allocated anew on each
iteration.
Reviewed by: kan
MFC after: 2 weeks
Features:
- network driver for the four 10G interfaces and two management ports
on XLP 8xx.
- Support 4xx and 3xx variants of the processor.
- Source code and firmware building for the 16 mips32r2 micro-code engines
in the Network Accelerator.
- Basic initialization code for Packet ordering Engine.
Submitted by: Prabhath Raman (prabhath at netlogicmicro com)
[refactored and fixed up for style by jchandra]
On XLP evaluation platform, the board information is stored
in an I2C eeprom and the network block configuration is available
from a CPLD connected to the GBU (NOR flash bus). Add support
for both of these.
Support for the Security and RSA blocks on XLP SoC. Even though
the XLP supports many more algorithms, only the ones supported
in OCF have been added.
Submitted by: Venkatesh J. V. (venkatesh at netlogicmicro com)
Add a Simple polled driver iicoc for the OpenCores I2C controller. This
is used in Netlogic XLP processors.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
The earlier version of the driver is sys/mips/rmi/dev/iic/ds1374u.c
Convert all references to ds1374u to ds1374, and use DEVMETHOD_END.
Also update the license header as Netlogic is now Broadcom.
- XLP supports hardware swap for PCIe IO/MEM accesses. Since we
are in big-endian mode, enable hardware swap and use the normal
bus space.
- move some printfs to bootverbose, and remove others.
- fix SoC device resource allocation code
- Do not use '|' while updating PCIE_BRIDGE_MSI_ADDRL
- some style fixes
In collaboration with: Venkatesh J. V. (venkatesh at netlogicmicro com)
Because the code lacks all the GNU extensions to printf() format stuff,
the compiler doesn't helpfully tell us that I messed up in a previous
commit.
Pointy hat to: adrian, who likely only cares about this because he's the
only one who bothers flipping on net80211 debugging.
uses of the page queues mutex with a new rwlock that protects the page
table and the PV lists. This reduces system time during a parallel
buildworld by 35%.
Reviewed by: alc
within the BAW.
This regression was introduced in ane earlier commit by me to fix the
BAW seqno allocation-but-not-insertion-into-BAW race. Since it was only
ever using the to-be allocated sequence number, any frame retries
with the first frame in the BAW still in the software queue would
have constantly failed, as ni_txseqs[tid] would always be outside
the BAW.
TODO:
* Extract out the mostly common code here in the agg and non-agg ADDBA
case and stuff it into a single function.
PR: kern/166357
pam_exec(8) now accepts a new option "return_prog_exit_status". When
set, the program exit status is used as the pam_exec return code. It
allows the program to tell why the step failed (eg. user unknown).
However, if it exits with a code not allowed by the calling PAM service
module function (see $PAM_SM_FUNC below), a warning is logged and
PAM_SERVICE_ERR is returned.
The following changes are related to this new feature but they apply no
matter if the "return_prog_exit_status" option is set or not.
The environment passed to the program is extended:
o $PAM_SM_FUNC contains the name of the PAM service module function
(eg. pam_sm_authenticate).
o All valid PAM return codes' numerical values are available
through variables named after the return code name. For instance,
$PAM_SUCCESS, $PAM_USER_UNKNOWN or $PAM_PERM_DENIED.
pam_exec return code better reflects what went on:
o If the program exits with !0, the return code is now
PAM_PERM_DENIED, not PAM_SYSTEM_ERR.
o If the program fails because of a signal (WIFSIGNALED) or doesn't
terminate normally (!WIFEXITED), the return code is now
PAM_SERVICE_ERR, not PAM_SYSTEM_ERR.
o If a syscall in pam_exec fails, the return code remains
PAM_SYSTEM_ERR.
waitpid(2) is called in a loop. If it returns because of EINTR, do it
again. Before, it would return PAM_SYSTEM_ERR without waiting for the
child to exit.
Several log messages now include the PAM service module function name.
The man page is updated accordingly.
Reviewed by: gleb@, des@
Sponsored by: Yakaz (http://www.yakaz.com)
MFC after: 2 weeks
Function acquired reader lock if needed.
Assert check for reader or writer lock (RA_LOCKED / RA_UNLOCKED)
- While here, add knlist_init_mtx.9 to MLINKS and fix some style(9) issues
Reviewed by: glebius
Approved by: ae(mentor)
MFC after: 2 weeks
