whatever frequency it started at instead of always picking the highest
frequency. The first version of this driver attempted to do this, but it
set the speed to the first frequency in the list rather than the value it
had saved.
MFC after: 1 week
Discussed with: rpaulo, phk
10 microseconds is too short.
Always set the cpu to the highest frequency so that we get through
boot and don't handicap cpus where powerd(8) is not used.
10 microseconds is too short.
Always set the cpu to the highest frequency so that we get through
boot and don't handicap cpus where powerd(8) is not used.
present in cpu_feature2. Also, use CPUID2_EST rather than a magic
number.
- Don't free the ACPI settings list in detach if we are going to fail the
request. Otherwise an attempt to kldunload est would free the array
but the driver would keep trying to use it.
MFC after: 1 week
CPUFREQ_DRV_SETTINGS(). The value of count on input is used to
prefent overflow of the settings buffer passed into CPUFREQ_DRV_SETTINGS().
This corrects the "est: CPU supports Enhanced Speedstep, but is not recognized."
error on my system.
MFC after: 1 week
of the magic string is passed in a 32-bit register, we can't use high
memory in the PAE case. This also eliminates a use of vtophys().
Tested by: Jeff Shimbo <jts767 / gmail.com>
MFC after: 1 week
o remove errata_a0 and introduce the corresponding flags into 'errata'.
o introduce a new errata for K8, namely some platform might set the
PENDING_BIT but aren't able to unset it, also don't loop forever
waiting PENDING_BIT being cleared.
o try to introduce a workaround for the PENDING_BIT stuck problem,
o support now half multipliers for K8.
Tested by: Abdullah Al-Marrie
Approved by: njl
Remove an unnecessary check of the table's bus clock. CPUs that
support this feature export only the high/low settings via the MSR,
packed into 32 bits.
Hardware from: Centaur Technologies
MFC after: 1 week
settings and is an older version of the same design used for ICH SpeedStep.
It is only known to be available on PIIX4 chipsets.
Many thanks to Bruno Ducrot for writing the driver and Jon Noack for
testing.
Submitted by: Bruno Ducrot
checks, including cpuid_is_k7(), will catch CPUs that really don't support
this method.
Submitted by: Bruno Ducrot
Tested by: Jari Kirma (kirma cs.hut.fi)
and AMD Cool&Quiet PowerNow! (k8) cpufreq control. This driver is enabled
for both i386 and amd64 architectures. It has both acpi and legacy BIOS
attachments. Thanks to Bruno Ducrot for writing this driver and Jung-uk
Kim for testing.
Submitted by: Bruno Ducrot (ducrot:poupinou.org)
modern CPUs that have multiple VID#s that aren't detectable via public
methods. We use the control value from acpi_perf as the id16 for setting
a given frequency.
SMP systems. It appears all drivers except ichss should attach to each
CPU and that settings should be performed on each CPU. Add comments about
this. Also, add a guard for p4tcc's identify method being called more than
once.
a bugfix of clearing the On-Demand flag when going back to 100%. It
has been tested and works on an IBM R32. Note original work done by
Ted Unangst and sobomax@.
on the previous generation of Pentium-M processors (Banias). Support for
Dothan and later processors involves working with acpi_perf(4) to extract
information about supported states. This driver should work on MP systems
including HTT. It is experimental and may have a few bugs but has been
tested to not crash at least.
Thanks to Colin Percival for his initial work on this driver.
reboot. Safter the reboot the TCC is usually in the Automatic mode, in which
reading current performance level is likely to produce bogus results make sure
to switch it to the On-Demand mode and set to some known performance level.
Unfortunately there is no reliable way to check that TCC is in the Automatic
mode. Reading bit 4 of ACPI Thermal Monitor Control Register produces 0
regardless of the current mode.
MFC after: 1 week
Suggested by: nate
- get rid of "magick" values in code and make sysctl's reflecting reality
on processor versions which have one or another frequency "forbidden"
due to errata.
MFC after: 2 weeks
CPU_ENABLE_TCC enables Thermal Control Circuitry (TCC) found in some
Pentium(tm) 4 and (possibly) later CPUs. When enabled and detected,
TCC allows to restrict power consumption by using machdep.cpuperf*
sysctls. This operates independently of SpeedStep and is useful on
systems where other mechanisms such as apm(4) or acpi(4) don't work.
Given the fact that many, even modern, notebooks don't work properly
with Intel ACPI, this is indeed very useful option for notebook owners.
Obtained from: OpenBSD
MFC after: 2 weeks
