APM BIOS was relevant only to early laptops (approximately P166 or
P200 and slower). These have not been relevant for a long time, and
this code has been untested for a long time (as far as I can
tell). The APM compat code in ACPI and the apm(8) command is not being
retired. Both of these items are still in use (apm(8) is more
scriptable than the replacement acpiconf, for the most part). This has
been commented out of i386 GENERIC since 2002. This code is not
relevant to any other port.
Discussed on: arch@
These kind of drops come for free in the sense that they do not use the
filter TCAM or any other resource that wouldn't normally be used during
rx. Frames dropped by the hardware get counted in the MAC's rx stats
but are not delivered to the driver.
hw.cxgbe.attack_filter
Set to 1 to enable the "attack filter". Default is 0. The attack
filter will drop an incoming frame if any of these conditions is true:
src ip/ip6 == dst ip/ip6; tcp and src/dst ip is not unicast; src/dst ip
is loopback (127.x.y.z); src ip6 is not unicast; src/dst ip6 is loopback
(::1/128) or unspecified (::/128); tcp and src/dst ip6 is mcast
(ff00::/8).
hw.cxgbe.drop_ip_fragments
Set to 1 to drop all incoming IP fragments. Default is 0. Note that
this drops valid frames.
hw.cxgbe.drop_pkts_with_l2_errors
Set to 1 to drop incoming frames with Layer 2 length or checksum errors.
Default is 1.
hw.cxgbe.drop_pkts_with_l3_errors
Set to 1 to drop incoming frames with IP version, length, or checksum
errors. Default is 0.
hw.cxgbe.drop_pkts_with_l4_errors
Set to 1 to drop incoming frames with Layer 4 length, checksum, or other
errors. Default is 0.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Cleanup all host resources, SYSCTLs, MSIX vectors and memory used
by the host and only leave the device allocated memory behind, if any,
because it may still be in use, when the PCI remove function is called.
Else future probe calls may fail due to SYSCTLs already existing.
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
The kernel globals for kenv are confined to 2 files that need them and
a few that likely shouldn't (but as written the code does). Move them
from sys/systm.h to sys/kenv.h. This removed a XXX from systm.h and
cleans it up a little bit...
Both cxgbe(4) and mlx5(4) wrapped the existing send tag header with
their own identical headers that stored the type that the
type-specific tag structures inherited from, so in practice it seems
drivers need this in the tag anyway. This permits removing these
extra header indirections (struct cxgbe_snd_tag and struct
mlx5e_snd_tag).
In addition, this permits driver-independent code to query the type of
a tag, e.g. to know what type of tag is being queried via
if_snd_query.
Reviewed by: gallatin, hselasky, np, kib
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D26689
This is described in RealTek's driver as a "RTL8168 Series add-on card."
PR: 250037
Submitted by: Hiroshi HASEGAWA <hhase1973@gmail.com>
MFC after: 1 week
Driver for pwm-backlight compatible device.
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26252
This is a simple subsystem that allow drivers to register as a backlight.
Each backlight creates a device node under /dev/backlight/backlightX and
an alias based on the name provided.
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D26250
These tunables can only be set to a valid cluster size (2K, 4K, 9K, or
16K) as documented in the man page. Anything else could lead to a
panic on interface up.
Reported by: mav@
MFC after: 1 week
Sponsored by: Chelsio Communications
Some DSDT entries have multiple interrupts for one device.
Add support for it.
This fixes ahci on NXP LS2160 and genet on RPi4
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: jhb
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D25145
ccr(4) uses software to handle GCM and CCM requests not supported by
the crypto engine (e.g. with only AAD and no payload). This change
adds a fallback for a few more requests such as those with more SGL
entries than can fit in a work request (this can happen for GCM when
decrypting a TLS record split across 15 or more packets).
Reported by: Chelsio QA
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D26582
Rather than placing the epoch around the entire receive loop which
might call into rtwn_rx_frame() and USB and sleep, split the loop
into two[1] and leave us with one unlock/lock cycle as well.
PR: 249925
Reported by: thj, (rkoberman gmail.com)
Tested by: thj
Suggested by: adrian [1]
Reviewed by: adrian
MFC after: 3 days
Sponsored by: The FreeBSD Foundation (initially, paniced my iwl lab host)
Differential Revision: https://reviews.freebsd.org/D26554
This is mostly needed for a common arm64/amd64 iommu code.
Reviewed by: kib
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D26587
This function isn't ACPI dependent and we may use it on FDT systems
as well.
o Don't repeat the function declaration, include iommu.h instead.
Reviewed by: andrew, kib
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D26584
Bind the netmap tx queues to a special '0xff' scheduling class which
makes the firmware skip some processing related to rate limiting on the
outgoing traffic. Future firmwares will do this automatically.
MFC after: 1 week
Sponsored by: Chelsio Communications
- Only active netmap receive queues should be in the RSS lookup table.
- The RSS table should be restored for NIC operation when the last
active netmap queue is switched off, not the first one.
- Support repeated netmap ON/OFF on a subset of the queues. This works
whether the the queues being enabled and disabled are the only ones
active or not. Some kring indexes have to be reset in the driver for
the second case.
MFC after: 1 week
Sponsored by: Chelsio Communications
In some cases, the syscon driver may be used by consumer requiring better
control about locking (ie. it may be used as registe file provider for clock
driver which needs locked access to multiple registers).
Add fine locking protocol methods together with bunch of helper functions
in syscon driver and implement this functionality in syscon_generic driver.
MFC after: 4 weeks
Syscon can also have child nodes that share a registration file with it.
To do this correctly, follow these steps:
- subclass syscon from simplebus and expose it if the node is also
"simple-bus" compatible.
- block simplebus probe for this compatible string, so it's priority
(bus pass) doesn't colide with syscon driver.
While I'm in, also block "syscon", "simple-mfd" for the same reason.
MFC after: 4 weeks
We have (two versions) of MS() and SM() macros which we use throughout
the wireless code. Change all but three places (ath_hal, rtwn, and rsu)
to the newly provided _IEEE80211_MASKSHIFT() and _IEEE80211_SHIFTMASK()
macros. Also change one internal case using both _S and _M instead of
just _S away from _M (one of the reasons rtwn and rsu were not changed).
This was done semi-mechanically. No functional changes intended.
Requested by: gnn (D26091)
Reviewed by: adrian (pre line wrap)
MFC after: 2 weeks
Sponsored by: Rubicon Communications, LLC (d/b/a "Netgate")
Differential Revision: https://reviews.freebsd.org/D26539
This allows the PF interfaces to communicate with the VF interfaces over
the internal switch in the ASIC. Fix the GL limits for VM work requests
while here.
MFC after: 3 days
Sponsored by: Chelsio Communications
vm_ooffset_t is now unsigned. Remove some tests for negative values,
or make other adjustments accordingly.
Reported by: Coverity
Reviewed by: kib markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D26214
Hardware assistance includes checksumming (tx and rx), TSO, and RSS on
the inner traffic in a VXLAN tunnel.
Relnotes: Yes
Sponsored by: Chelsio Communications
From Franco:
The iflib rewrite forced the promisc flag but it was not reported
to the system. Noticed on a stock VM that went into unsolicited
promisc mode when dhclient was started during bootup.
PR: 248869
Submitted by: Franco Fichtner <franco@opnsense.org>
Reviewed by: erj@
MFC after: 3 days
This re-adds the opt_rss.h header to the driver and includes some
RSS-specific headers when RSS is defined.
PR: 249191
Submitted by: Milosz Kaniewski <milosz.kaniewski@gmail.com>
MFC after: 3 days
We don't need to do the busy dance for this driver. It's handled by
destroy_dev() entirely. Since all we did was busy/unbusy in
open/close, just delete them. We therefore don't need to track closes
either.
Reviewed by: ian@
Differential Revision: https://reviews.freebsd.org/D26431
vendor ID string to say just "Microchip Technology" -- the buyout of
Standard Microsystems happened in 2012 and the SMC/SMSC names are pretty
much retired at this point.
PR: 241406
Add enough infrastructure for interrupts on children of the pl061 GPIO
controller. As gpiobus already provided these the pl061 driver also needs
to pass requests up the newbus hierarchy.
Currently there are no children that expect to configure interrupts, however
this is expected to change to support the ACPI Event Information interface.
Sponsored by: Innovate UK
that can be extended, but also ensure compile-time type checking. Refactor
common code out of arch-specific implementations. Move the mpr and mps
drivers to this new API. The template type remains visible to the consumer
so that it can be allocated on the stack, but should be considered opaque.
This update adds support for:
HW VLAN tagging
HW checksum offload for IPv4 and IPv6
tx and rx aggreegation (for full gige speeds)
multiple transactions
In my testing, I am able to get 900-950Mbps depending upon
TCP or UDP, which is a significant improvement over the previous
91Mbps (~8kint/sec*1500bytes/packet*1packet/int).
Reviewed by: hselasky
MFC after: 2 months
Differential Revision: https://reviews.freebsd.org/D25809
In r365419 ieee80211_media_change() callers were updated to not longer
act on the obselete ENETRESET return code.
While in the old days iwm has done a stop/init cycle in these cases,
this was not executed since r193340.
As a consequence simplify iwm code as well by passing ieee80211_media_change()
right to ieee80211_vap_attach() as there is no more need for a local
implementation.
Reported by: Tomoaki AOKI (junchoon dec.sakura.ne.jp)
Tested by: Tomoaki AOKI (junchoon dec.sakura.ne.jp)
MFC after: 3 days
X-MFC: fix is already in stable/12
PR: 248955
Summary of changes:
- Assorted bug fixes
- Support for newer versions of the device firmware
- Suspend/resume support
- Support for Lenient Link Mode for E82X devices (e.g. can try to link with
SFP/QSFP modules with bad EEPROMs)
- Adds port-level rx_discards sysctl, similar to ixl(4)'s
This version of the driver is intended to be used with DDP package 1.3.16.0,
which has already been updated in a previous commit.
Tested by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>
MFC after: 3 days
MFC with: r365332, r365550
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D26322
As the pl061 driver can be an interrupt controller attach it earlier in the
boot so other drivers can use it.
Use a new GPIO xref to not conflict with the existing root interrupt
controller.
Sponsored by: Innovate UK
It could be used in various IOMMU platforms, not only DMAR.
Reviewed by: kib
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D26373
On arm64 we may boot via ACPI. In this case we will still try to manage the
gpio providers as if we are using FDT. Fix this by checking if the FDT node
is valid before registering a cross reference.
Sponsored by: Innovate UK
Future changes would require additional initialization of OBJT_PHYS
objects, and vm_object_allocate() is not suitable for it.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D24652
The cryptodev_process() method should either return 0 if it has
completed a request, or ERESTART to defer the request until later. If
a request encounters an error, the error should be reported via
crp_etype before completing the request via crypto_done().
Fix a few more drivers noticed by asomers@ similar to the fix in
r365389. This is an old bug, but went unnoticed since crypto requests
did not start failing as a normal part of operation until digest
verification was introduced which can fail requests with EBADMSG.
PR: 247986
Reported by: asomers
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D26361
RISC-V is currently built with -Wno-format, which is how these went
undetected. Address them now before re-enabling those warnings.
Differential Revision: https://reviews.freebsd.org/D26319
A PL061 is a simple 8 pin GPIO controller. This GPIO device is used to
signal an internal request for shutdown on some virtual machines including
Arm-based Amazon EC2 instances.
Submitted by: Ali Saidi <alisaidi_amazon.com> (previouss version)
Reviewed by: Ali Saidi, manu
Differential Revision: https://reviews.freebsd.org/D24065
In r178354 with the introduction of multi-bss ("vap") support factoring
out started and with r193340 ieee80211_media_change() no longer returned
ENETRESET but only 0 or error.
As ieee80211(9) tells the ieee80211_media_change() function should not
be called directly but is registered with ieee80211_vap_attach() instead.
Some drivers have not been fully converted. After fixing the return
checking some of these functions were simply wrappers between
ieee80211_vap_attach() and ieee80211_media_change(), so remove the extra
function, where possible as well.
PR: 248955
Submitted by: Tong Zhang (ztong0001 gmail.com) (original)
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
At least on Orange Pi PC Plus even the host mode does not work without
enabling the phy and setting it to the host mode.
The driver will now parse dr_mode property and will try to configure
itself and the phy accordingly.
OTG mode is not supported yet, so it is treated as the device / peripheral
mode.
The phy is enabled -- powered on -- only for the host mode.
The device mode requires support from a phy driver, e.g., aw_usbphy on
Allwinner platform.
aw_usbphy does not support the device mode, so it cannnot work yet.
MFC after: 6 weeks
Otherwise, I get this panic:
panic: awusbdrd_reg: Invalid register 0x342
It looks that musb code both writes and reads at least MUSB2_REG_TXDBDIS.
MFC after: 5 weeks
X-MFC after: r365399
Make that distinction more explicit and regular in the code.
The difference in behavior is documented in the respective datasheets.
Previously, the code handled the distinction by writing the control
register multiple times where at least one write was zero and another
was one.
This can be considered a follow-up to r363021.
Reviewed by: manu
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D26308
wakeup() does not have any effect on pause(), so if a transfer was
not finished by the time of the first check, then the thread
would sleep full 30 ms.
To do: protect the transfer and interrupt code with the mutex,
switch from tsleep from msleep
Reviewed by: manu
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D26309
abs() takes a (signed) int as input.
Instead, it was used with unsigned 64-bit integers.
So, add and use a new helper function to calculate a difference between
two uint64_t-s.
Reviewed by: manu
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D26307
Investigating a hang I found having some more error information
available would be helpful, so be more verbose and also tell cam/xpt
status in case of error/panic.
Reviewed by: hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D26287
While debugging a hang I noticed that in case of error in
umass_cam_attach_sim() we miss a cam_sim_free() call.
Added that to not leak resources.
Reviewed by: hselasky
MFC after: 3 days
Differential Revision: D26287
Fix the build after r365264, I forgot to exclude arm in one more place.
Reported by: rpokala
Approved by: manu (implicit, build fix)
MFC after: 3 days
X-MFC-With: 365264
Pointy-hat to: zeising
mgb had a longstanding typo in function-like macro MGB_NEXT_RING_IDX's
argument, but the macro had no consumers. r365061 introduced a use of
the macro, after which mgb failed to build.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
hints data. Control register 2 holds the settings a user might want to
configure, such as the timeout value for idle busses and whether to enable
the mass-writes feature.
Also add hint support for disconnecting idle busses (which was already
supported using FDT data).
Update the manpage with the new features, and also split the hints section
into separate lists of required and optional hints.
This allows privileged userspace processes to find information about the
physical page backing a given mapping. It is useful in applications
such as DPDK which perform some of their own memory management.
Reviewed by: kib, jhb (previous version)
MFC after: 2 weeks
Sponsored by: Juniper Networks, Inc.
Sponsored by: Klara Inc.
Differential Revision: https://reviews.freebsd.org/D26237
Further improve the drm2 deprecation message, only displaying information
about the port for relevant architectures, and skipping the message
completely from arm, which uses some parts of drm2 still.
This is mostly intended to be merged to 12, since the base bits of drm2 on
FreeBSD 13 are only really used on arm.
Reviewed by: manu, mmel
Approved by: manu
MFC after: 3 days
X-MFC-with: r364737
Differential Revision: https://reviews.freebsd.org/D26275
Add support for new devices which are capable of 2.5 and 5G speeds, as well as
Energy Efficient Ethernet (EEE):
- introduce new device ids
- add ability to select 2.5 and 5G speeds on devices which support it
- add sysctls to enable EEE and read related statistics
Submitted by: Krzysztof Galazka <krzysztof.galazka@intel.com>
Reviewed by: #IntelNetworking
MFC after: 3 days
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D25549
