copied and pasted. I had actually tested without this change in my
trees as had the other testers.
Reported by: bde, Rostislav Krasny rosti dot bsd at gmail dot com
Approved by: re (scottl)
Pointy hat to: jhb
packet filter. This would cause a panic on architectures that require strict
alignment such as sparc64 (tier1) and ia64/ppc (tier2).
This adds two new macros that check the alignment, these are compile time
dependent on __NO_STRICT_ALIGNMENT which is set for i386 and amd64 where
alignment isn't need so the cost is avoided.
IP_HDR_ALIGNED_P()
IP6_HDR_ALIGNED_P()
Move bridge_ip_checkbasic()/bridge_ip6_checkbasic() up so that the alignment
is checked for ipfw and dummynet too.
PR: ia64/81284
Obtained from: NetBSD
Approved by: re (dwhite), mlaier (mentor)
as they are already default for I686_CPU for almost 3 years, and
CPU_DISABLE_SSE always disables it. On the other hand, CPU_ENABLE_SSE
does not work for I486_CPU and I586_CPU.
This commit has:
- Removed the option from conf/options.*
- Removed the option and comments from MD NOTES files
- Simplified the CPU_ENABLE_SSE ifdef's so they don't
deal with CPU_ENABLE_SSE from kernel configuration. (*)
For most users, this commit should be largely no-op. If you used to
place CPU_ENABLE_SSE into your kernel configuration for some reason,
it is time to remove it.
(*) The ifdef's of CPU_ENABLE_SSE are not removed at this point, since
we need to change it to !defined(CPU_DISABLE_SSE) && defined(I686_CPU),
not just !defined(CPU_DISABLE_SSE), if we really want to do so.
Discussed on: -arch
Approved by: re (scottl)
by amd64 and i386: For buffered writes we collect data and write it
out a ${DEV_BSIZE}-sized block at a time. The fragsz variable is used
to keep track of how much data we have collected in the buffer so far
and it's reset to zero immediately after writing a block to the dump
device.
When the last, possibly partially filled buffer is flushed, we didn't
reset fragsz to 0 and as such would stop reflecting reality. Since we
currently only need to do buffered writes once, this isn't a problem.
However, when kernel dumps are made by hand (say by callling doadump
from within DDB), the improperly cleared state from the first call to
dumpsys causes the next call to dumpsys to create an invalid code file.
This change resets fragsz after flushing the partially filled buffer so
that it fixes the two problems at once.
Approved by: re (scottl)
timer since irq0 isn't being driven at hz in that case and we don't need to
try to handle edge cases with rollover, etc. that require irq0 to be firing
for the timecounter to actually work.
Submitted by: phk
Tested by: schweikh
Approved by: re (scottl)
that newer Intel cpu hardware implements them too. This includes things
like the NX (pte no-execute) flag for execute protection. We'll need to
reference this for implementing no-exec in pmap.c at some point.
Some feature flags are duplicated in both the Intel-orignated bits and
the AMD bits. Suppress the the duplicates correctly - the old code
assumed they were a 1:1 mapping which is not correct. We can't just mask
off the bits present in cpu_feature.
Converge with amd64 where this originated from.
Intel cpu's that implement any AMD features will report them in dmesg now.
Approved by: re
dump format. The key reason to do this is so that we can dump sparse
address space. For example, we need to be able to skip the PCI hole
just below the 4GB boundary. Trying to destructively dump MMIO device
registers is Really Bad(TM). The frequent result of trying to do a
crash dump on a machine with 4GB or more ram was ugly (lockup or reboot).
This code has been taken directly from the IA64 dump_machdep.c code,
with just a few (mostly minor) mods.
Introduce a dump_avail[] array in the machdep.c code so that we have a
source of truth for what memory is present in a machine that needs to be
dumped. We can't use phys_avail[] because all sorts of things slice
memory out of it that we really need to dump. eg: the vm page array
and the dmesg buffer. dump_avail[] is pretty much an unmolested version
of phys_avail[]. It does have Maxmem correction.
Bump the i386 and amd64 dump format to version 2, but nothing actually
uses this. amd64 was actually using the i386 dump version number.
libkvm support to follow.
Approved by: re
fields for each system call, I missed two system call files because
they weren't named syscalls.master. Catch up with this last two,
mapping the system calls to the NULL event for now.
Spotted by: jhb
Approved by: re (scottl)
files after they were repo-copied to sys/dev/atkbdc. The sources of
atkbdc(4) and its children were moved to the new location in preparation
for adding an EBus front-end to atkbdc(4) for use on sparc64; i.e. in
order to not further scatter them over the whole tree which would have
been the result of adding atkbdc_ebus.c in e.g. sys/sparc64/ebus. Another
reason for the repo-copies was that some of the sources were misfiled,
e.g. sys/isa/atkbd_isa.c wasn't ISA-specific at all but for hanging
atkbd(4) off of atkbdc(4) and was renamed to atkbd_atkbdc.c accordingly.
Most of sys/isa/psm.c, i.e. expect for its PSMC PNP part, also isn't
ISA-specific.
- Separate the parts of atkbdc_isa.c which aren't actually ISA-specific
but are shareable between different atkbdc(4) bus front-ends into
atkbdc_subr.c (repo-copied from atkbdc_isa.c). While here use
bus_generic_rl_alloc_resource() and bus_generic_rl_release_resource()
respectively in atkbdc_isa.c instead of rolling own versions.
- Add sparc64 MD bits to atkbdc(4) and atkbd(4) and an EBus front-end for
atkbdc(4). PS/2 controllers and input devices are used on a couple of
Sun OEM boards and occur on either the EBus or the ISA bus. Depending on
the board it's either the only on-board mean to connect a keyboard and
mouse or an alternative to either RS232 or USB devices.
- Wrap the PSMC PNP part of psm.c in #ifdef DEV_ISA so it can be compiled
without isa(4) (e.g. for EBus-only machines). This ISA-specific part
isn't separated into its own source file, yet, as it requires more work
than was feasible for 6.0 in order to do it in a clean way. Actually
philip@ is working on a rewrite of psm(4) so a more comprehensive
clean-up and separation of hardware dependent and independent parts is
expected to happen after 6.0.
Tested on: i386, sparc64 (AX1105, AXe and AXi boards)
Reviewed by: philip
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
vm_page's machine-dependent fields. Use this function in
vm_pageq_add_new_page() so that the vm_page's machine-dependent and
machine-independent fields are initialized at the same time.
Remove code from pmap_init() for initializing the vm_page's
machine-dependent fields.
Remove stale comments from pmap_init().
Eliminate the Boolean variable pmap_initialized from the alpha, amd64,
i386, and ia64 pmap implementations. Its use is no longer required
because of the above changes and earlier changes that result in physical
memory that is being mapped at initialization time being mapped without
pv entries.
Tested by: cognet, kensmith, marcel
- Implement sampling modes and logging support in hwpmc(4).
- Separate MI and MD parts of hwpmc(4) and allow sharing of
PMC implementations across different architectures.
Add support for P4 (EMT64) style PMCs to the amd64 code.
- New pmcstat(8) options: -E (exit time counts) -W (counts
every context switch), -R (print log file).
- pmc(3) API changes, improve our ability to keep ABI compatibility
in the future. Add more 'alias' names for commonly used events.
- bug fixes & documentation.
audit event identifier associated with each system call, which will
be stored by makesyscalls.sh in the sy_auevent field of struct sysent.
For now, default the audit identifier on all system calls to AUE_NULL,
but in the near future, other BSM event identifiers will be used. The
mapping of system calls to event identifiers is many:one due to
multiple system calls that map to the same end functionality across
compatibility wrappers, ABI wrappers, etc.
Submitted by: wsalamon
Obtained from: TrustedBSD Project
exist on other architectures yet.
- While I'm here, fix the formatting of the options line. The keyword
"options" should be followed by a space and then a tab, not 2 tabs.
of MCOUNT to have a C version and an asm version with the same name and
not have LOCORE ifdefs to distinguish them. <machine/profile.h> provides
a C version and <machine/asmacros.h> provides an assembler version.
Discussed with: bde
i8253reg.h, and add some defines to control a speaker.
- Move PPI related defines from i386/isa/spkr.c into ppireg.h and use them.
- Move IO_{PPI,TIMER} defines into ppireg.h and timerreg.h respectively.
- Use isa/isareg.h rather than <arch>/isa/isa.h.
Tested on: i386, pc98
- Move MD files into <arch>/<arch>.
- Move bus dependent files into <arch>/<bus>.
Rename some files to more suitable names.
Repo-copied by: peter
Discussed with: imp
in as-yet uncommitted code for 32 bit binary compatability on 64 bit
kernels, some of the 32 bit registers come from the pcb. Moving the
initialization here means fill_regs32() etc are laid out the same.
Have pmcstat(8) and pmccontrol(8) use these APIs.
Return PMC class-related constants (PMC widths and capabilities)
with the OP GETCPUINFO call leaving OP PMCINFO to return only the
dynamic information associated with a PMC (i.e., whether enabled,
owner pid, reload count etc.).
Allow pmc_read() (i.e., OPS PMCRW) on active self-attached PMCs to
get upto-date values from hardware since we can guarantee that the
hardware is running the correct PMC at the time of the call.
Bug fixes:
- (x86 class processors) Fix a bug that prevented an RDPMC
instruction from being recognized as permitted till after the
attached process had context switched out and back in again after
a pmc_start() call.
Tighten the rules for using RDPMC class instructions: a GETMSR
OP is now allowed only after an OP ATTACH has been done by the
PMC's owner to itself. OP GETMSR is not allowed for PMCs that
track descendants, for PMCs attached to processes other than
their owner processes.
- (P4/HTT processors only) Fix a bug that caused the MI and MD
layers to get out of sync. Add a new MD operation 'get_config()'
as part of this fix.
- Allow multiple system-mode PMCs at the same row-index but on
different CPUs to be allocated.
- Reject allocation of an administratively disabled PMC.
Misc. code cleanups and refactoring. Improve a few comments.
