This is important in hostap, ibss, (11s at some magical future date, etc)
where different nodes may have smaller limits.
Oops!
MFC after: 1 week
Relnotes: Yes
This adds a workaround to incorrectly behaving APs (ie, FreeBSD APs) which
don't beacon out exactly when they should (at TBTT multiples of beacon
intervals.)
It forces the hardware awake (but leaves it in network-sleep so self
generated frames still state that the hardware is asleep!) and will
remain awake until the next sleep transition driven by net80211.
That way if the beacons are just at the wrong interval, we get a much
better chance of hearing more consecutive beacons before we go to sleep,
thus not constantly disconnecting.
Tested:
* AR9485, STA mode, against a misbehaving FreeBSD AP.
The 802.11-2012 spec talks about this - section 10.1.3.2 - Beacon Generation
in Infrastructure Networks. So yes, we should be expecting beacons to be
going out in multiples of intval.
Silly adrian.
So:
* fix the FreeBSD APs that are sending beacons at incorrect TBTTs (target
beacon transmit time); and
* yes indeed we will have to wake up out of network sleep until we sync
a beacon.
This was being done in the pre-AR9380 case, but not for AR9380 and later.
When powersave in STA mode is enabled, this may have lead to the transmit
completion code doing this:
* call the task, which doesn't wake up the hardware
* complete the frames, which doesn't touch the hardware
* schedule pending frames on the hardware queue, which DOES touch the
hardware, and this will be ignored
This would show up in the logs like this:
(with debugging enabled):
Nov 27 23:03:56 lovelace kernel: Q1[ 0] (nseg=1) (DS.V:0xfffffe011bd57300 DS.P:0x49b57300) I: 168cc117 L:00000000 F:0005
...
(in general, doesn't require debugging enabled):
Nov 27 23:03:56 lovelace kernel: ath_hal_reg_write: reg=0x00000804, val=0x49b57300, pm=2
That register is a EDMA TX FIFO register (queue 1), and the val is the descriptor
being written.
Whilst here, make sure the software queue gets kicked here.
Tested;
* AR9485, STA mode + powersave
This bug has been bugging me for quite some time. I finally sat down
with enough coffee to figure it out.
The short of it - rounding up to the next intval multiple of the TSF value
only works if the AP is transmitting all its beacons on an interval of
the TSF. If it isn't - for example, doing staggered beacons on a multi-VAP
setup with a single hardware TSF - then weird things occur.
The long of it -
When powersave is enabled, the MAC and PHY are partially powered off.
They can't receive any packets (or transmit, for that matter.)
The target beacon timer programming will wake up the MAC/PHY just before
the beacon is supposed to be received (well, strictly speaking, at DTIM
so it can see the TIM - traffic information map - telling the STA whether
any traffic is there for it) and it happens automatically.
However, this relies on the target beacon time being programmed correctly.
If it isn't then the hardware will wake up and not hear any beacons -
and then it'll be asleep for said beacons. After enough of this, net80211
will give up and assume the AP went away.
This should fix both TSFOOR interrupts and disconnects from APs with powersave
enabled.
The annoying bit is that it only happens if APs stagger things or start
on a non-zero TSF. So, this would sometimes be fine and sometimes not be
fine.
What:
* I don't know (yet) why the code rounds up to the next intval.
For now, just disable rounding it and trust the value we get.
TODO:
* If we do see a beacon miss in STA mode then we should transition
out of sleep for a while so we can hear beacons to resync against.
I'd love a patch from someone to enable that particular behaviour.
Note - that doesn't require that net80211 brings the chip out of
sleep state - only that we wake the chip up through to full-on and
then let it go to sleep again when we've seen a beacon. The wifi
stack and AP can still completely just stay believing we're in sleep
mode.
Tested:
* AR9485, STA mode, powersave enabled
MFC after: 1 week
Relnotes: Yes
* Obey the peer A-MPDU density if it's larger than the currently configured
one.
* Pay attention to the peer A-MPDU max-size and don't assume we can transmit
a full A-MPDU (64k!) if the peer announces smaller values.
Relnotes: ath(4): Fix A-MPDU transmit; obey A-MPDU density and max size.
This is a long time coming. The general pieces have been floating around
in a local repo since circa 2012 when I dropped the net80211 support
into the tree.
This allows the per-chain RSSI and NF to show up in 'ifconfig wlanX list sta'.
I haven't yet implemented the EVM hookups so that'll show up; that'll come
later.
Thanks to Susie Hellings <susie@susie.id.au> who did the original work
on this a looong time ago for a company we both worked at.
* Don't do RTS/CTS - experiments show that we get ACK frames for each of them
and this ends up causing the timestamps to look all funny.
* Set the HAL_TXDESC_POS bit, so the AR9300 HAL sets up the hardware to return
location and CSI information.
* change the HT_RC_2_MCS to do MCS0..23
* Use it when looking up the ht20/ht40 array for bits-per-symbol
* add a clk_to_psec (picoseconds) routine, so we can get sub-microsecond
accuracy for the math
* .. and make that + clk_to_usec public, so higher layer code that is
returning clocks (eg the ANI diag routines, some upcoming locationing
experiments) can be converted to microseconds.
Whilst here, add a comment in ar5416 so i or someone else can revisit the
latency values.
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
The 11n duration calculation function in net80211 and the HAL round /up/
the duration calculation for short-gi, so we can't use that.
The 11n duration calculation doesn't know about the extra symbol time
needed for STBC, nor the LDPC encoding duration, so we can't use
that.
This (along with other, local hacks) allow the locationing services to
get down to around 200nS (yes, nanoseconds) of variance when speaking
to a "good" AP.
Tested:
* AR9380, STA mode, local locationing frame hacks
The pre-11n calculations include SIFS, but the 11n ones don't.
The reason is that (mostly) the 11n hardware is doing the SIFS calculation
for us but the pre-11n hardware isn't. This means that we're over-shooting
the times in the duration field for non-11n frames on 11n hardware, which
is OK, if not a little inefficient.
Now, this is all fine for what the hardware needs for doing duration math
for ACK, RTS/CTS, frame length, etc, but it isn't useful for doing PHY
duration calculations. Ie, given a frame to TX and its timestamp, what
would the end of the actual transmission time be; and similar for an
RX timestamp and figuring out its original length.
So, this adds a new field to the duration routines which requests
SIFS or no SIFS to be included. All the callers currently will call
it requesting SIFS, so this /should/ be a glorious no-op. I'm however
planning some future work around airtime fairness and positioning which
requires these routines to have SIFS be optional.
Notably though, the 11n version doesn't do any SIFS addition at the moment.
I'll go and tweak and verify all of the packet durations before I go and
flip that part on.
Tested:
* AR9330, STA mode
* AR9330, AP mode
* AR9380, STA mode
* the code already stored the length of the RX desc, which I never used.
So, use that and retire the new flag I introduced a while ago.
* Introduce a TX timestamp length field and capability.
* extend the TX timestamp to 32 bits, as the AR5416 and later does a full
32 bit TX timestamp instead of 15 or 16 bits.
* add RX descriptor fields for PHY uploaded information (coming soon)
* add flags for RX/TX fast timestamp, hardware upload, etc
* add a flag for TX to request ToD/ToA location information.
I keep asking myself "what do these fields mean" and so now I've clarified
it for myself.
Tested:
* Reading the comments, going "a-ha!" a couple times.
Approved by: re (gjb)
It turns out that getting decent performance requires stacking the TX
FIFO a little more aggressively.
* Ensure that when we complete a frame, we attempt to push a new frame
into the FIFO so TX is kept as active as it needs to be
* Be more aggressive about batching non-aggregate frames into a single
TX FIFO slot. This "fixes" TDMA performance (since we only get one
TX FIFO slot ungated per DMA beacon alert) but it does this by pushing
a whole lot of work into the TX FIFO slot.
I'm not /entirely/ pleased by this solution, but it does fix a whole bunch
of corner case issues in the transmit side and fix TDMA whilst I'm at it.
I'll go revisit transmit packet scheduling in ath(4) post 11.
Tested:
* AR9380, STA mode
* AR9580, hostap mode
* AR9380, TDMA client mode
Approved by: re (hrs)
This started showing up when doing lots of aggregate traffic. For TDMA it's
always no-ACK traffic and I didn't notice this, and I didn't notice it
when doing 11abg traffic as it didn't fail enough in a bad way to trigger
this.
This showed up as the fifo depth being < 0.
Eg:
Jun 19 09:23:07 gertrude kernel: ath0: ath_tx_edma_push_staging_list: queued 2 packets; depth=2, fifo depth=1
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1, bf=0xfffffe000385f068, start=1, end=1
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1: FIFO depth is now 0 (1)
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1, bf=0xfffffe0003866fe8, start=0, end=1
Jun 19 09:23:07 gertrude kernel: ath0: ath_edma_tx_processq: Q1: FIFO depth is now -1 (0)
So, clear the flags before adding them to a TX queue, so if they're
re-added for the retransmit path it'll clear whatever they were and
not double-account the FIFOEND flag. Oops.
Tested:
* AR9380, STA mode, 11n iperf testing (~130mbit)
Approved by: re (delphij)
It turns out the frame scheduling policies (eg DBA_GATED) operate on
a single TX FIFO entry. ASAP scheduling is fine; those frames always
go out.
DBA-gated sets the TX queue ready when the DBA timer fires, which triggers
a beacon transmit. Normally this is used for content-after-beacon queue
(CABQ) work, which needs to burst out immediately after a beacon.
(eg broadcast, multicast, etc frames.) This is a general policy that you
can use for any queue, and Sam's TDMA code uses it.
When DBA_GATED is used and something like say, an 11e TX burst window,
it only operates on a single TX FIFO entry. If you have a single frame
per TX FIFO entry and say, a 2.5ms long burst window (eg TDMA!) then it'll
only burst a single frame every 2.5ms. If there's no gating (eg ASAP) then
the burst window is fine, and multiple TX FIFO slots get used.
The CABQ code does pack in a list of frames (ie, the whole cabq) but
up until this commit, the normal TX queues didn't. It showed up when
I started to debug TDMA on the AR9380 and later.
This commit doesn't fix the TDMA case - that's still broken here, because
all I'm doing here is allowing 'some' frames to be bursting, but I'm
certainly not filling the whole TX FIFO slot entry with frames.
Doing that 'properly' kind of requires me to take into account how long
packets should take to transmit and say, doing 1.5 or something times that
per TX FIFO slot, as if you partially transmit a slot, when it's next
gated it'll just finish that TX FIFO slot, then not advance to the next
one.
Now, I /also/ think queuing a new packet restarts DMA, but you have to
push new frames into the TX FIFO. I need to experiment some more with
this because if it's really the case, I will be able to do TDMA support
without the egregious hacks I have in my local tree. Sam's TDMA code
for previous chips would just kick the TXE bit to push along DMA
again, but we can't do that for EDMA chips - we /have/ to push a new
frame into the TX FIFO to restart DMA. Ugh.
Tested:
* AR9380, STA mode
* AR9380, hostap mode
* AR9580, hostap mode
Approved by: re (gjb)
Some later code I'll commit pushes lists of frames into the EDMA TX
FIFO, rather than a single frame at a time. The CABQ code already
pushes frame lists, but it turns out we should actually be doing it
in general or performance tanks. :(
This is the initial framework to call into the MCI HAL routines and drive
the basic state engine.
The MCI bluetooth coex model uses a command channel between wlan and
bluetooth, rather than a 2-wire or 3-wire signaling protocol to control things.
This means the wlan and bluetooth chip exchange a lot more information and
signaling, even at the per-packet level. The NICs in question can share
the input LNA and output PA on the die, so they absolutely can't stomp
on each other in a silly fashion. It also allows for the bluetooth side
to signal when profiles come and go, so the driver can take appropriate
control. There's also the possibility of dynamic bluetooth/wlan duty cycle
control which I haven't yet really played with.
It configures things up with a static "wlan wins everything" coexistence,
configures up the available 2GHz channel map for bluetooth, sets a static
duty cycle for bluetooth/wifi traffic priority and drives the basics needed to
keep the MCI HAL code happy.
It doesn't do any actual coexistence except to default to "wlan wins everything",
which at least demonstrates that things do indeed work. Bluetooth inquiry frames
still trump wifi (including beacons), so that demonstrates things really do
indeed seem to work.
Tested:
* AR9462 (WB222), STA mode + bt
* QCA9565 (WB335), STA mode + bt
TODO:
* .. the rest of coexistence. yes, bluetooth, not people. That stuff's hard.
* It doesn't do the initial BT side calibration, which requires a WLAN chip
reset. I'll fix up the reset path a bit more first before I enable that.
* The 1-ant and 2-ant configuration bits aren't being set correctly in
if_ath_btcoex.c - I'll dig into that and fix it in a subsequent commit.
* It's not enabled by default for WB222/WB225 even though I believe it now
can be - I'll chase that up in a subsequent commit.
Obtained from: Qualcomm Atheros, Linux ath9k
The legacy bits are just from ah.h; the MCI bits are from the ar9300
HAL "freebsd" extras.
A subsequent commit will include ah_btcoex.h into ah.h and remove
the older defintions.
This is like the WB222 coexistence (ie, "MCI", a message bus inside the
chip), and it's currently a cut/paste so I can start using it to flesh
out the differences with WB222.
It doesn't completely /do/ bluetooth coexistence, because it turns out
I need to add some contigmalloc'ed buffers to the btcoex path for this
type of hardware. I'm putting this work in the "people would like
to see functioning-ish btcoex before FreeBSD-11" bucket because I see
this as "broken".
Tested:
* QCA9535 (WB335) NIC, BT + 2GHz STA
Split getchannels() method in ath_hal/ah_regdomain.c into a subset
of functions for better readability.
Note: due to different internal structure, it cannot use
ieee80211_add_channel*() (however, some parts are done in a
similar manner).
Differential Revision: https://reviews.freebsd.org/D6139
I .. can't believe I missed this.
This showed up because the AP was TX'ing LDPC to an iwm(4) chipset,
which didn't advertise LDPC and doesn't /accept/ LDPC. Amusingly, all
the two other FreeBSD 11n parts I had tested with (AR9380, Intel 7260)
and I completely forgot to test on ye olde hardware.
That'll teach me.
Tested:
* AR9580 (AP) - Intel 7260 (STA), AR9380 (STA), Intel 6205 (STA)
LDPC adds better transmit reliability if both ends support it.
You in theory can do both STBC and LDPC at the same time.
If I see issues I'll disable it.
* Only enable it if both ends of a connection negotiate it.
* Disable it if any rate is non-11n.
* Count both LDPC TX and STBC TX.
Tested:
* AR9380, STA mode
This enables LDPC receive support for the AR9300 chips that support it.
It'll announce LDPC support via net80211.
Tested:
* AR9380, STA mode
* AR9331, (to verify the HAL didn't attach it to a chip which
doesn't support LDPC.)
TODO:
* Add in net80211 machinery to make this configurable at runtime.
Add support for the FHT_STBC_TX flag in iv_flags_ht, so it'll now obey
the per-vap ifconfig stbctx flag.
This means that we can do STBC TX on one vap and not another VAP.
(As well as STBC RX on said vap; that changes the HTCAP announcement.)
le*dec / le*enc functions.
Replace net80211 specific macros with system-wide bytestream
encoding/decoding functions:
- LE_READ_2 -> le16dec
- LE_READ_4 -> le32dec
- LE_WRITE_2 -> le16enc
- LE_WRITE_4 -> le32enc
+ drop ieee80211_input.h include, where it was included for these
operations only.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6030
* Don't use arbitrary frames for the average RX RSSI - only frames
from the current BSSID
* Don't log / do the syncbeacon logic for another BSSID and definitely
don't do the syncbeacon call if we miss beacons outside of STA mode.
* Don't do the IBSS merge bits if the current node plainly won't ever
match our current BSS (ie, the IBSS doesn't have to match, but all
the same bits that we check in ieee80211_ibss_merge() have to match.)
Tested:
* ath(4), AR9380, IBSS mode, surrounded by a lot of IBSS 11ac networks.
Sponsored by: Eva Automation, Inc.
It turns out that these will clash very annoyingly with the linux
macros in the linuxkpi layer, so let the wookie^Wlinux win.
The only user that I can find is ath(4), so fix it there too.
taskqueue_enqueue() was changed to support both fast and non-fast
taskqueues 10 years ago in r154167. It has been a compat shim ever
since. It's time for the compat shim to go.
Submitted by: Howard Su <howard0su@gmail.com>
Reviewed by: sephe
Differential Revision: https://reviews.freebsd.org/D5131
These are going to be much more efficient on low end embedded systems
but unfortunately they make it .. less convenient to implement correct
bus barriers and debugging. They also didn't implement the register
serialisation workaround required for Owl (AR5416.)
So, just remove them for now. Later on I'll just inline the routines
from ah_osdep.c.
The ath hal and driver code all assume the world is an x86 or the
bus layer does an explicit bus flush after each operation (eg netbsd.)
However, we don't do that.
So, to be "correct" on platforms like sparc64, mips and ppc (and maybe
ARM, I am not sure), just do explicit barriers after each operation.
Now, this does slow things down a tad on embedded platforms but I'd
rather things be "correct" versus "fast." At some later point if someone
wishes it to be fast then we should add the barrier calls to the HAL and
driver.
Tested:
* carambola 2 (AR9331.)
The synth programming here requires the real centre frequency,
which for HT20 channels is the normal channel, but HT40 is
/not/ the primary channel. Everything else was using 'freq',
which is the correct centre frequency, but the hornet config
was using 'ichan' to do the lookup which was also the primary
channel.
So, modify the HAL call that does the mapping to take a frequency
in MHz and return the channel number.
Tested:
* Carambola 2, AR9331, tested both HT/20 and HT/40 operation.
This probe/attaches correctly in my local branch and now displays
a useful message:
ath0: <Qualcomm Atheros QCA953x> at mem 0x18100000-0x1811ffff irq 0 on nexus0
...
ath0: AR9530 mac 1280.0 RF5110 phy 0.0
I added MYBEACON support a while ago to listen to beacons that are only
for your configured BSSID. For AR9380 and later NICs this results in
a lot less chip wakeups in station mode as it then only shows you beacons
that are destined to you.
However in IBSS mode you really do want to hear all beacons so you can do
IBSS merges. Oops.
So only use MYBEACON for STA + not-scanning, and just use BEACON for
the other modes it used to use BEACON for.
This doesn't completely fix IBSS merges though - there are still some
conditions to chase down and fix.
This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
Right now the only way to force a cold reset is:
* The HAL itself detects it's needed, or
* The sysctl, setting all resets to be cold.
Trouble is, cold resets take quite a bit longer than warm resets.
However, there are situations where a cold reset would be nice.
Specifically, after a stuck beacon, BB/MAC hang, stuck calibration results,
etc.
The vendor HAL has a separate method to set the reset reason (which is
how HAL_RESET_BBPANIC gets set) which informs the HAL during the reset path
why it occured. This is almost but not quite the same; I may eventually
unify both approaches in the future.
This commit just extends HAL_RESET_TYPE to include both status (eg BBPANIC)
and type (eg do COLD.) None of the HAL code uses it yet though; that'll
come later.
It also is a big no-op in each HAL - I need to go teach each of the HALs
about cold/warm reset through this path.
to transmit the buffer.
ath_tx_start() may manipulate/reallocate the mbuf as part of the DMA
code, so we can't expect the mbuf can be returned back to the caller.
Now, the net80211 ifnet work changed the semantics slightly so
if an error is returned here, the mbuf/reference is freed by the
caller (here, it's net80211.)
So, once we reach ath_tx_start(), we never return failure. If we fail
then we still return OK and we free the mbuf/noderef ourselves, and
we increment OERRORS.
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
This was off because the net80211 aggregation code was using the same
state pointers for both fast frames and ampdu tx support which led to some
pretty unfortunate panic-y behaviour.
Now that net80211 doesn't panic, let's flip this back on.
It doesn't (yet) do the horrific sounding thing of A-MPDU aggregates
of fast frames; that'll come next. It's a pre-requisite to supporting
AMSDU + AMPDU anyway, which actually speeds things up quite considerably
(think packing lots of little ACK frames into a single AMSDU.)
Tested:
* QCA955x SoC, AP mode
* AR5416, STA mode
* AR9170, STA mode (with local fast frame patches)
The MAC can be fetched from the key struct.
I added the ndis updates to make it compile.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3657
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
is detaching.
This mostly fixes a panic - the reset path shouldn't run whilst
the NIC is being torn down.
It's not locked, so it's "mostly" ok, but most of the rest of
the driver doesn't read sc->invalid with sensible locking. Grr.
The real solution is to cleanly tear down taskqueues in the detach/suspend
phase, but ..
This stops the panics that occur on MIPS platforms when doing say,
'sysctl dev.ath.0' whilst the MAC is asleep. The MIPS platform is
rather unforgiving in getting power-save register access wrong and you
will get all kinds of odd failures if you don't have things woken
up at the right times.
Tested:
* QCA9558 (TP-Link Archer C7 v2)
* AR9331 (Carambola 2)
.. with no VAPs configured and ath0 down (thus the MAC is definitely
asleep.)
PR: kern/201117
Smart NICs with firmware (eg wpi, iwn, the new atheros parts, the intel 7260
series, etc) support doing a lot of things in firmware. This includes but
isn't limited to things like scanning, sending probe requests and receiving
probe responses. However, net80211 doesn't know about any of this - it still
drives the whole scan/probe infrastructure itself.
In order to move towards suppoting smart NICs, the receive path needs to
know about the channel/details for each received packet. In at least
the iwn and 7260 firmware (and I believe wpi, but I haven't tried it yet)
it will do the scanning, power-save and off-channel buffering for you -
all you need to do is handle receiving beacons and probe responses on
channels that aren't what you're currently on. However the whole receive
path is peppered with ic->ic_curchan and manual scan/powersave handling.
The beacon parsing code also checks ic->ic_curchan to determine if the
received beacon is on the correct channel or not.[1]
So:
* add freq/ieee values to ieee80211_rx_stats;
* change ieee80211_parse_beacon() to accept the 'current' channel
as an argument;
* modify the iv_input() and iv_recv_mgmt() methods to include the rx_stats;
* add a new method - ieee80211_lookup_channel_rxstats() - that looks up
a channel based on the contents of ieee80211_rx_stats;
* if it exists, use it in the mgmt path to switch the current channel
(which still defaults to ic->ic_curchan) over to something determined
by rx_stats.
This is enough to kick-start scan offload support in the Intel 7260
driver that Rui/I are working on. It also is a good start for scan
offload support for a handful of existing NICs (wpi, iwn, some USB
parts) and it'll very likely dramatically improve stability/performance
there. It's not the whole thing - notably, we don't need to do powersave,
we should not scan all channels, and we should leave probe request sending
to the firmware and not do it ourselves. But, this allows for continued
development on the above features whilst actually having a somewhat
working NIC.
TODO:
* Finish tidying up how the net80211 input path works.
Right now ieee80211_input / ieee80211_input_all act as the top-level
that everything feeds into; it should change so the MIMO input routines
are those and the legacy routines are phased out.
* The band selection should be done by the driver, not by the net80211
layer.
* ieee80211_lookup_channel_rxstats() only determines 11b or 11g channels
for now - this is enough for scanning, but not 100% true in all cases.
If we ever need to handle off-channel scan support for things like
static-40MHz or static-80MHz, or turbo-G, or half/quarter rates,
then we should extend this.
[1] This is a side effect of frequency-hopping and CCK modes - you
can receive beacons when you think you're on a different channel.
In particular, CCK (which is used by the low 11b rates, eg beacons!)
is decodable from adjacent channels - just at a low SNR.
FH is a side effect of having the hardware/firmware do the frequency
hopping - it may pick up beacons transmitted from other FH networks
that are in a different phase of hopping frequencies.
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
I .. stupidly added code to return HAL_ANI_STATS to HAL_DIAG_ANI_STATS.
I discovered this in a noisy environment when the returned values were
enough to .. well, make everything terrible.
So - restore functionality.
Tested:
* AR5416 (uses the AR5212 HAL), in a /very/ noisy 2GHz environment.
Enough to trigger ANI to get upset and generate useful data.
