This change will enable IPMI access on 5717/5718/5719/5720 and 5761
controllers. Because ASF is not available when APE firmware is
present, bge_allow_asf tunable is ignored when driver detects APE
firmware. Also bge(4) no longer performs two resets(one blind
reset and the other reset with firmware in mind) in device attach.
Now bge(4) performs a reset with enough information in bge_reset().
The APE firmware also needs special handling to make suspend/resume
work but it was not implemented yet.
With this change, bge(4) should work on any 5717/5718/5719/5720
controllers. Special thanks to Mike Hibler at Emulab who setup
remote debugging on Dell R820. Without his help I couldn't be able
to address several issues happened on Dell Rx20 systems. And many
thanks to Broadcom for continuing to support FreeBSD!
Submitted by: davidch (initial version)
H/W donated by: Broadcom
Tested by: many
Tested on: Del R820/R720/R620/R420/R320 and HP Proliant DL 360 G8
handling(jumbo, wire speed etc) in brgphy_reset(). Touching
BRGPHY_MII_AUXCTL register seems to confuse APE firmware such that
it couldn't establish a link.
BGE_PCI_PCISTATE register before issuing global reset. After
issuing reset, it reads BGE_PCI_PCISTATE register again and
compares the saved register value and current value. It was used to
know whether the global reset operation was completed or not.
Unfortunately, this logic caused several issues on recent BCM5717/
5718/5719 and BCM5720 controllers. It seems APE firmware accesses
some registers while global reset is in progress such that reading
BGE_PCI_PCISTATE register after reset does not yield old pre-reset
state value. This resulted in consuming too much time in global
reset and sometimes it couldn't successfully complete reset.
The BGE_MISCCFG_RESET_CORE_CLOCKS of BGE_MISC_CFG register is
self-clearing bit so driver is able to know the reset completion.
But the core-lock reset will disable indirect/flat/standard access
modes such that driver cannot poll BGE_MISCCFG_RESET_CORE_CLOCKS
bit of BGE_MISC_CFG register. So just wait enough time for
core-clock reset to complete.
Data sheet says driver should wait 100us for PCI/PCI-X devices and
100ms for PCIe devices. I chose 1ms for PCI/PCI-X since this value
was used for many years in bge(4). For PCIe devices, use 100ms as
recommended by data sheet.
bge_chipinit() also cleared BGE_MAC_MODE register which shall clear
firmware configured mode information. I think this will result in
losing ASF/IPMI link in device attachment. Let bge_reset() honor
firmware configured BGE_MAC_MODE register and don't announce driver
is UP in bge_reset(). Firmware should have control over driver until
it's fully initialized by driver.
While I'm here, enable workaround for PCI-X BCM5704 A0 in
bge_reset(). This will prevent internal arbitration logic from
switching to the other DMA engine after a retry cycle.
set not-NULL during SIM registration and set to UMASS_GONE on destruction.
Debug messages there look broken for at least 9 years, as they dereference
softc value that was just checked to be equal to NULL.
- Remove magic pointer value UMASS_GONE and use simple NULL instead.
Found by: Clang Static Analyzer
When creating MCAsmBackend pass the CPU string as well. In X86AsmBackend
store this and use it to not emit long nops when the CPU is geode which
doesnt support them.
Fixes PR11212.
Pull in r164133 from upstream clang trunk:
Follow up on llvm r164132.
This should prevent illegal instructions when building world on Geode
CPUs (e.g. Soekris).
MFC after: 3 days
Prevents a lockup when queried a deliberately constructed combination
of records. [CVE-2012-5166]
For more information: https://kb.isc.org/article/AA-00801
division by zero later if event timer's minimal period is above one second.
For now it is just a theoretical possibility.
Found by: Clang Static Analyzer
returns zero while request status is not CAM_REQ_CMP. That could cause
partial device attach or other unexpected results.
Found by: Clang Static Analyzer
enabled. This eliminates one mtx_lock() per each routing lookup thus improving
performance in several cases (routing to directly connected interface or routing
to default gateway).
Icmp redirects should not be used to provide routing direction nowadays, even
for end hosts. Routers should not use them too (and this is explicitly restricted
in IPv6, see RFC 4861, clause 8.2).
Current commit changes rnh_machaddr function to 'stock' rn_match (and back) for every
AF_INET routing table in given VNET instance on drop_redirect sysctl change.
This change is part of bigger patch eliminating rte locking.
Sponsored by: Yandex LLC
MFC after: 2 weeks
While here, change ISCI_LED to ISCI_PHY since conceptually the hardware
ties the LEDs to a phy and the LEDs for a given phy cannot be controlled
independently.
Submitted by: Paul Maulberger <Paul.Maulberger at gmx.de> (with modifications)
information from the transceivers connected to the ports of a
cxgbe(4) based card.
# cxgbetool t4nex0 i2c <port_id> <dev_addr> <addr> [<count>]
For example:
# cxgbetool t4nex0 i2c 0 0xa0 3
0x10 [16]
(As per SFF-8472 the SFP+ module is at 0xa0 and bit 4 in the value at
address 3 indicates it's a 10Gbase-SR module, which it is.)
This lets userspace read arbitrary information from the SFP+ modules
etc. on this bus.
Reading multiple bytes in the same transaction isn't possible right now.
I'll update the driver once the chip's firmware supports this.
MFC after: 3 days
reference a missing dependency rather than a missing compile command.
- Don't append a newline to the auto-generated compile command. The
compile command has a newline appended when it is later output to the
Makefile.
MFC after: 2 weeks
that requires 10ms delay after device reset. Because that code was
there from day 1, I guess it was added to give enough settlement
time after updating BGE_MAC_MODE register.
The recommended delay time for BGE_MAC_MODE after updating is 40us
and it was already done in r241219.
The VCPU(Virtual CPU) of BCM5906 is used to provide a mechanism to
control the bootcode execution and to pick up configuration data
stored inside the EEPROM.
The bootcode of BCM5906 will check the BGE_VCPU_STATUS_DRV_RESET
bit to decide which booting procedure to choose.
Data sheet indicates the VCPU of BCM5906 should set
BGE_VCPU_STATUS_DRV_RESET bit *before* VCPU reset or global reset.
water mark to 256 bytes. Otherwise controller will encounter DMA
write under run errors and would result in RX DMA hang. If the
maximum payload size is 128 bytes, the water mark is set to 128
bytes as usual.
While here, set maximum read request size to 2048 for BCM5719/BCM5720.
For other PCIe devices, use 4096. And reprogram the maximum read
request size whenever device reset is performed.
make analog input loopback and dual-stream playback work by enabling
signal mixing by nid 22, as it should be according to info returned by
the CODEC. Otherwise pin nid 28 receives only signal from DAC nid 16.
PR: kern/169124
MFC after: 1 week
instruction loads/stores at its will.
The macro __compiler_membar() is currently supported for both gcc and
clang, but kernel compilation will fail otherwise.
Reviewed by: bde, kib
Discussed with: dim, theraven
MFC after: 2 weeks
srandomdev(). This doesn't actually work
with any modern C compiler:
In particular, both clang and modern gcc
verisons silently elide any xor operation
with 'junk'.
Approved by: secteam
MFC after: 3 days
r234247.
Use, instead, the static intializer introduced in r239923 for x86 and
sparc64 intr_cpus, unwinding the code to the initial version.
Reviewed by: marius
executed to better differentiate between loader-specific errors and kernel-
specific errors (if ever any of either).
This type of functionality hasn't been required before the introduction of the
advanced menu system (r222417). Adding this functionality will help different-
iate errors at the loader-level such as a BTX halt caused by heap exhaustion
and errors that may be involved with executing the kernel (wrong architecture
for example). A user can learn that messages before "Booting..." are related to
the loader(8) environment and it's Forth-ilk, while those after are not
related to loader(8) -- the point that loader(8) has ``left the building''.
This patch also includes a man-page update to color.4th(8) as the color logic
moves to a lower-level (from being included by beastie.4th to being included
by loader.4th).
After noticing a delay between execution of the overloaded "boot" FICL word and
the display of text on-screen, gcooper confirmed that the introduction of a
builtin memory test (disabled by adding hw.memtest.tests="0" to loader.conf(5))
was the cause of the delay.
This patch adds an echo to produce "Booting..." when the overloaded "boot" word
is executed (this includes from the interactive command-prompt on all arches,
from the menu system on arches that run the beastie menu, and even those arches
that run the menu but disable it by setting beastie_disable="YES" in
loader.conf(5)). When loader_color="YES" in loader.conf(5), the same message is
produced but in white text on a blue background (only the letters produced have
this background -- opposed to perhaps the entire line).
