Convert the array to use C99 initializers.
Make it constant.
Replace MAX_TRAP_MSG with nitems().
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
These calls are not the same in general: the former will dequeue the
page if it is enqueued, while the latter will just leave it alone. But,
all existing uses of the former apply to unmanaged pages, which are
never enqueued in the first place. No functional change intended.
Reviewed by: kib
MFC after: 1 week
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20470
When disabling the last enabled userspace probe, fasttrap clears the
function pointers which hook in to the breakpoint handler. If a traced
thread hit a fasttrap breakpoint before it was removed, we must ensure
that it is able to call the hook; otherwise fasttrap will not consume
the trap and SIGTRAP will be delievered to the thread. Synchronize
with such threads by ensuring that they load the hook pointer with
interrupts disabled, and by completing an SMP rendezvous after removing
breakpoints and before clearing the pointers.
Reported by: Alexander Alexeev <Alexander.Alexeev@dell.com>
Tested by: Alexander Alexeev (earlier version)
Reviewed by: cem, kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20526
pci_alloc_msix() requires both the table and PBA BARs to be allocated
by the driver. ppt was only allocating the table BAR so would fail
for devices with the PBA in a separate BAR. Fix this by allocating
the PBA BAR before pci_alloc_msix() if it is stored in a separate BAR.
While here, release BARs after calling pci_release_msi() instead of
before. Also, don't call bus_teardown_intr() in error handling code
if bus_setup_intr() has just failed.
Reported by: gallatin
Tested by: gallatin
Reviewed by: rgrimes, markj
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D20525
in the loss of a KASSERT that guarded against the invalidation a wired
mapping. Restore this KASSERT.
Remove an unnecessary KASSERT from pmap_demote_pde_locked(). It guards
against a state that was already handled at the start of the function.
Reviewed by: kib
X-MFC with: r348476
If service code faulted, we might end up unwinding with interrupts
disabled. Top-level kernel code should have interrupts enabled, which
is enforced by checks.
Save %rflags before entering EFI, and restore to the known good value
on return. This handles situation with disabled interrupts on fault
and perhaps other potential bugs, e.g. invalid value for PSL_D.
Reported and tested by: Jan Martin Mikkelsen <janm@transactionware.com>
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
debugging checks.
In particular,
- Move the code to handle failure to allocate page table page into
a helper.
- After the previous item is done, it is possible to distinguish !PG_A
case and case of missed page, in the control flow.
- Make the variable to indicate that in-kernel mapping is demoted.
- Assert that missed page table page can only happen for in-kernel
mapping when demoting direct map.
- If DIAGNOSTIC is enabled, and the page table page should be already
filled, check all ptes instead of only first one.
Reviewed by: alc, markj
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20266
syscalls.conf is included using "." which per the Open Group:
If file does not contain a <slash>, the shell shall use the search
path specified by PATH to find the directory containing file.
POSIX shells don't fall back to the current working directory.
Submitted by: Nathaniel Wesley Filardo <nwf20@cl.cam.ac.uk>
Reviewed by: bdrewery
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D20476
tables which affect demotion.
The last last-level page table under 2M mappings below KERNend was
only partially initialized. When that page was used as the hardware
page table for demotion of the 2M mapping, the result was not
consistent. Since pmap_demote_pde() is switched to use PG_PROMOTED as
the test for the validity of the saved last level page table page, we
can keep page table pages zero-initialized instead. Demotion would
fill them as needed.
Only map the created page tables beyond KERNend, there is no need to
pre-promote PTmap after KERNend, because the extra mapping is not used.
Only round up *firstaddr to 2M boundary when it is below rounded
KERNend. Sometimes the allocpages() calls advance *firstaddr past the
end of the last 2MB page mapping. In that case, this conditional
avoids wasting an average of 1MB of physical memory.
Update comments to explain action in more clean and direct language.
Reported and tested by: pho
In collaboration with: alc
Sponsored by: The FreeBSD Foundation (kib)
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20380
The upper bound for the valid address from the large map used
LARGEMAP_MAX_ADDRESS instead of LARGEMAP_MIN_ADDRESS. Provide a
function-like macro for proper upper value.
Noted by: markj
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20386
Similar to PG_FRAME and PG_PS_FRAME, it denotes the mask of the
physical address component of 1G superpage PDP entry.
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20386
It is possible for the kernel mapping to be created with superpage by
directly installing pde using pmap_enter_2mpage() without filling the
corresponding page table page. This can happen e.g. if the range is
already backed by reservation and vm_fault_soft_fast() conditions are
satisfied, which was observed on the pipe_map.
In this case, demotion must fill the page obtained from the pmap
radix, same as if the page is newly allocated. Use PG_PROMOTED bit as
an indicator that the page is valid, instead of the wire count of the
page table page.
Since the PG_PROMOTED bit is set on pde when we leave TLB entries for
4k pages around, which in particular means that the ptes were filled,
it provides more correct indicator. Note that pmap_protect_pde()
clears PG_PROMOTED, which handles the case when protection was changed
on the superpage without adjusting ptes.
Reported by: pho
In collaboration with: alc
Tested by: alc, pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D20380
If MDS mitigation is enabled by the tunable but MDS microcode is not
early-loaded, software mitigation is selected. This causes
initializecpu() to try to allocate memory which makes boot process
very unhappy.
Create SYSINIT that runs sufficiently late to succeed.
Reported by: naddy
PR: 237968
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
Submitted by: Patrick Mooney <pmooney@pfmooney.com>
Reviewed by: kib
Tested by: Patrick on SmartOS with Linux and Windows guests
Obtained from: Joyent
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D20296
Apparently, there is more code trying to call pmap_remove() early,
mostly to free preloaded memory. Instead of moving all deallocations
to the point where a scheduler is initialized, add missed setup of
thread0 di init at hammer_time().
The code in pmap_delayed_invl_start_u() is modified to not ever take
the thread lock if the thread priority is less or equal to PVM. Since
thread0 starts at priority 0, and then is reset to PVM at
proc0_init(), this eliminates taking the thread lock during early
boot.
While there, fix off by one in comparision of the base priority.
Reported and tested by: bcran (previous version)
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 29 days
In all practical situations, the resolver visibility is static.
Requested by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: so (emaste)
Differential revision: https://reviews.freebsd.org/D20281
This is done mostly for debugging in field. Also added the sysctl of
the same name to report used mode.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
For machines having cmpxcgh16b instruction, i.e. everything but very
early Athlons, provide lockless implementation of delayed
invalidation.
The implementation maintains lock-less single-linked list with the
trick from the T.L. Harris article about volatile mark of the elements
being removed. Double-CAS is used to atomically update both link and
generation. New thread starting DI appends itself to the end of the
queue, setting the generation to the generation of the last element
+1. On DI finish, thread donates its generation to the previous
element. The generation of the fake head of the list is the last
passed DI generation. Basically, the implementation is a queued
spinlock but without spinlock.
Many thanks both to Peter Holm and Mark Johnson for keeping with me
while I produced intermediate versions of the patch.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
MFC note: td_md.md_invl_gen should go to the end of struct thread
Differential revision: https://reviews.freebsd.org/D19630
of the 'flags' argument to mmap(2) with Linux strace(1).
Reviewed by: dchagin
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20223
Microarchitectural buffers on some Intel processors utilizing
speculative execution may allow a local process to obtain a memory
disclosure. An attacker may be able to read secret data from the
kernel or from a process when executing untrusted code (for example,
in a web browser).
Reference: https://www.intel.com/content/www/us/en/security-center/advisory/intel-sa-00233.html
Security: CVE-2018-12126, CVE-2018-12127, CVE-2018-12130, CVE-2019-11091
Security: FreeBSD-SA-19:07.mds
Reviewed by: jhb
Tested by: emaste, lwhsu
Approved by: so (gtetlow)
of them listed in opt_global.h which is not generated while building
modules outside of a kernel and such modules never match real cofigured
kernel.
So, we should prevent our users from building obviously defective modules.
Therefore, remove the root cause of the building of modules outside of a
kernel - the possibility of building modules with DEBUG or KTR flags.
And remove all of DEBUG printfs as it is incomplete and in threaded
programms not informative, also a half of system call does not have DEBUG
printf. For debuging Linux programms we have dtrace, ktr and ktrace ability.
PR: 222861
Reviewed by: trasz
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20178
Historically we have not distinguished between kernel wirings and user
wirings for accounting purposes. User wirings (via mlock(2)) were
subject to a global limit on the number of wired pages, so if large
swaths of physical memory were wired by the kernel, as happens with
the ZFS ARC among other things, the limit could be exceeded, causing
user wirings to fail.
The change adds a new counter, v_user_wire_count, which counts the
number of virtual pages wired by user processes via mlock(2) and
mlockall(2). Only user-wired pages are subject to the system-wide
limit which helps provide some safety against deadlocks. In
particular, while sources of kernel wirings typically support some
backpressure mechanism, there is no way to reclaim user-wired pages
shorting of killing the wiring process. The limit is exported as
vm.max_user_wired, renamed from vm.max_wired, and changed from u_int
to u_long.
The choice to count virtual user-wired pages rather than physical
pages was done for simplicity. There are mechanisms that can cause
user-wired mappings to be destroyed while maintaining a wiring of
the backing physical page; these make it difficult to accurately
track user wirings at the physical page layer.
The change also closes some holes which allowed user wirings to succeed
even when they would cause the system limit to be exceeded. For
instance, mmap() may now fail with ENOMEM in a process that has called
mlockall(MCL_FUTURE) if the new mapping would cause the user wiring
limit to be exceeded.
Note that bhyve -S is subject to the user wiring limit, which defaults
to 1/3 of physical RAM. Users that wish to exceed the limit must tune
vm.max_user_wired.
Reviewed by: kib, ngie (mlock() test changes)
Tested by: pho (earlier version)
MFC after: 45 days
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D19908
This gets rid of the global cpu_ipi_pending array.
While replace cmpset with fcmpset in the delivery code and opportunistically
check if given IPI is already pending.
Sponsored by: The FreeBSD Foundation
Having IPSEC compiled into the kernel imposes a non-trivial
performance penalty on multi-threaded workloads due to IPSEC
refcounting. In my benchmarks of multi-threaded UDP
transmit (connected sockets), I've seen a roughly 20% performance
penalty when the IPSEC option is included in the kernel (16.8Mpps
vs 13.8Mpps with 32 senders on a 14 core / 28 HTT Xeon
2697v3)). This is largely due to key_addref() incrementing and
decrementing an atomic reference count on the default
policy. This cause all CPUs to stall on the same cacheline, as it
bounces between different CPUs.
Given that relatively few users use ipsec, and that it can be
loaded as a module, it seems reasonable to ask those users to
load the ipsec module so as to avoid imposing this penalty on the
GENERIC kernel. Its my hope that this will make FreeBSD look
better in "out of the box" benchmark comparisons with other
operating systems.
Many thanks to ae for fixing auto-loading of ipsec.ko when
ifconfig tries to configure ipsec, and to cy for volunteering
to ensure the the racoon ports will load the ipsec.ko module
Reviewed by: cem, cy, delphij, gnn, jhb, jpaetzel
Differential Revision: https://reviews.freebsd.org/D20163
tun(4) and tap(4) share the same general management interface and have a lot
in common. Bugs exist in tap(4) that have been fixed in tun(4), and
vice-versa. Let's reduce the maintenance requirements by merging them
together and using flags to differentiate between the three interface types
(tun, tap, vmnet).
This fixes a couple of tap(4)/vmnet(4) issues right out of the gate:
- tap devices may no longer be destroyed while they're open [0]
- VIMAGE issues already addressed in tun by kp
[0] emaste had removed an easy-panic-button in r240938 due to devdrn
blocking. A naive glance over this leads me to believe that this isn't quite
complete -- destroy_devl will only block while executing d_* functions, but
doesn't block the device from being destroyed while a process has it open.
The latter is the intent of the condvar in tun, so this is "fixed" (for
certain definitions of the word -- it wasn't really broken in tap, it just
wasn't quite ideal).
ifconfig(8) also grew the ability to map an interface name to a kld, so
that `ifconfig {tun,tap}0` can continue to autoload the correct module, and
`ifconfig vmnet0 create` will now autoload the correct module. This is a
low overhead addition.
(MFC commentary)
This may get MFC'd if many bugs in tun(4)/tap(4) are discovered after this,
and how critical they are. Changes after this are likely easily MFC'd
without taking this merge, but the merge will be easier.
I have no plans to do this MFC as of now.
Reviewed by: bcr (manpages), tuexen (testing, syzkaller/packetdrill)
Input also from: melifaro
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20044
While Linux strace(1) doesn't strictly require it - it has a fallback
to PTRACE_GETREGS - it's a newer interface, so we better support it
before the old one is deprecated.
Reviewed by: dchagin
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20152
IPI_STOP is used after panic or when ddb is entered manually. MONITOR/
MWAIT allows CPUs that support the feature to sleep in a low power way
instead of spinning. Something similar is already used at idle.
It is perhaps especially useful in oversubscribed VM environments, and is
safe to use even if the panic/ddb thread is not the BSP. (Except in the
presence of MWAIT errata, which are detected automatically on platforms with
known wakeup problems.)
It can be tuned/sysctled with "machdep.stop_mwait," which defaults to 0
(off). This commit also introduces the tunable
"machdep.mwait_cpustop_broken," which defaults to 0, unless the CPU has
known errata, but may be set to "1" in loader.conf to signal that mwait
wakeup is broken on CPUs FreeBSD does not yet know about.
Unfortunately, Bhyve doesn't yet support MONITOR extensions, so this doesn't
help bhyve hypervisors running FreeBSD guests.
Submitted by: Anton Rang <rang AT acm.org> (earlier version)
Reviewed by: kib
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20135
Rather than just accessing it via pointer cast.
No functional change intended.
Discussed with: kib (earlier version)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20135
OVMF's flash variable storage is using add instructions when indexing
the variable store bootrom location.
Submitted by: D Scott Phillips <d.scott.phillips@intel.com>
Reviewed by: rgrimes
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D19975
move bits that are MI out into the headers in compat/linux.
For that remove bogus _packed attribute from struct l_sockaddr
and use MI types for struct members.
And continue to move into the linux_common module a code that is
intended for both Linuxulator modules (both instruction set - 32 & 64 bit)
or for external modules like linsysfs or linprocfs.
To avoid header pollution introduce new sys/compat/linux_common.h header.
Reviewed by: emaste
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20137
Use it wherever COMPAT_FREEBSD11 is currently specified, like r309749.
Reviewed by: imp, jhb, markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20120
Replace most VM_MAXCPU constant useses with an accessor function to
vm->maxcpus which for now is initialized and kept at the value of
VM_MAXCPUS.
This is a rework of Fabian Freyer (fabian.freyer_physik.tu-berlin.de)
work from D10070 to adjust it for the cpu topology changes that
occured in r332298
Submitted by: Fabian Freyer (fabian.freyer_physik.tu-berlin.de)
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Approved by: bde (mentor), jhb (maintainer)
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D18755
After the referenced commit, we did not set x87 and sse valid bits in
the xstate_bv bitmask for initial fpu state (stored in memory), when
using XSAVE.
The state is loaded into FPU register file to initialize the process
FPU state, and since both bits were clear, the default x87 and SSE
states were loaded. By chance, FreeBSD ABI SSE2 state is same as FPU
initial state, so the bug is not visible for 64bit processes. But on
i386, the precision control should be set to double (53bit mantissa),
instead of the default double extended (64bit mantissa). For 32bit
processes on amd64, kernel reloads control word with the right mask,
which only left native i386 and amd64 native but using x87 as
affected.
Fix it by setting minimal required xstate_bv mask.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Some early PCIe chipsets are explicitly listed in the white-list to
enable use of the MMIO config space accesses, perhaps because ACPI
tables were not reliable source of the base MCFG address at that time.
For that chipsets, MCFG base was read from the known chipset MCFGbase
config register.
During very early stage of boot, when access to the PCI config space
is performed (see e.g. pci_early_quirks.c), we cannot map 255MB of
registers because the method used with pre-boot pmap overflows initial
kernel page tables.
Move fallback to read MCFGbase to the attachment method of the
x86/legacy device, which removes code duplication, and results in the
use of io accesses until MCFG is parsed or legacy attach called.
For amd64, pre-initialize cfgmech with CFGMECH_1, right now we
dynamically assign CFGMECH_1 to it anyway, and remove checks for
CFGMECH_NONE.
There is a mention in the Intel documentation for corresponding
chipsets that OS must use either io port or MMIO access method, but we
already break this rule by reading MCFGbase register, so one more
access seems to be innocent.
Reported by: longwitz@incore.de
PR: 236838
Reviewed by: avg (other version), jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19833
For PCI device (i.e. child of a PCI bus), reset tries FLR if
implemented and worked, and falls to power reset otherwise.
For PCIe bus (child of a PCIe bridge or root port), reset
disables PCIe link and then re-trains it, performing what is known as
link-level reset.
Reviewed by: imp (previous version), jhb (previous version)
Sponsored by: Mellanox Technologies
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D19646
Remove redundant npxsave_core definition while here.
Suggested by: Anton Rang
Reviewed by: kib, Anton Rang <rang AT acm.org>
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D19665
For 32-bit Linuxulator, ipc() syscall was historically
the entry point for the IPC API. Starting in Linux 4.18, direct
syscalls are provided for the IPC. Enable it.
MFC after: 1 month
AMD64_SET_**BASE expects a pointer to a pointer, we just passing in the pointer value itself.
Set PCB_FULL_IRET for doreti to restore %fs, %gs and its correspondig base.
PR: 225105
Reported by: trasz@
MFC after: 1 month
There are some unusual cases where a process may cause an mlock()ed
range of memory to be unmapped. If the application subsequently
faults on that region, the handler may attempt to create a superpage
mapping backed by the resident, wired pages. However, the pmap code
responsible for creating such a mapping (pmap_enter_pde() on i386
and amd64) does not ensure that a leaf page table page is available
if the superpage is later demoted; the demotion operation must therefore
perform a non-blocking page allocation and must unmap the entire
superpage if the allocation fails. The pmap layer ensures that this
can never happen for wired mappings, and so the case described above
breaks that invariant.
For now, simply ensure that the MI fault handler never attempts to
create a wired superpage except via promotion.
Reviewed by: kib
Reported by: syzbot+292d3b0416c27c131505@syzkaller.appspotmail.com
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19670
It may happen on some machines, that even if SGX is disabled
in firmware, the driver would still attach despite EPC base and
size equal zero. Such behaviour causes a kernel panic when the
module is unloaded. Add a simple check to make sure we
only attach when these values are correctly set.
Submitted by: Kornel Duleba <mindal@semihalf.com>
Reviewed by: br
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D19595
Add the infrastructure to allow MD procctl(2) commands, and use it to
introduce amd64 PTI control and reporting. PTI mode cannot be
modified for existing pmap, the knob controls PTI of the new vmspace
created on exec.
Requested by: jhb
Reviewed by: jhb, markj (previous version)
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
PTI mode for the process pmap on exec is activated iff P_MD_PTI is set.
On exec, the existing vmspace can be reused only if pti mode of the
pmap matches the P_MD_PTI flag of the process. Add MD
cpu_exec_vmspace_reuse() callback for exec_new_vmspace() which can
vetoed reuse of the existing vmspace.
MFC note: md_flags change struct proc KBI.
Reviewed by: jhb, markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
When the pmap with pti disabled (i.e. pm_ucr3 == PMAP_NO_CR3) is
activated, tss.rsp0 was not updated. Any interrupt that happen before
next context switch would use pti trampoline stack for hardware frame
but fault and interrupt handlers are not prepared to this. Correctly
update tss.rsp0 for both PMAP_NO_CR3 and pti pmaps.
Note that this case, pti = 1 but pmap->pm_ucr3 == PMAP_NO_CR3 is not
used at the moment.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D19514
and for %ecx after RDTSCP.
Initialize TSC_AUX MSR with CPUID. It allows for userspace to cheaply
identify CPU it was executed on some time ago, which is sometimes useful.
Note: The values returned might be changed in future.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Research Unix, 7th Edition introduced TIMEZONE and DSTFLAG
compile-time constants in sys/param.h to communicate these values for
the machine. 4.2BSD moved from the compile-time to run-time and
introduced these variables and used for localtime() to return the
right offset from UTC (sometimes referred to as GMT, for this purpose
is the same). 4.4BSD migrated to using the tzdata code/database and
these variables were basically unused.
FreeBSD removed the real need for these with adjkerntz in
1995. However, some RTC clocks continued to use these variables,
though they were largely unused otherwise. Later, phk centeralized
most of the uses in utc_offset, but left it using both tz_minuteswest
and adjkerntz.
POSIX (IEEE Std 1003.1-2017) states in the gettimeofday specification
"If tzp is not a null pointer, the behavior is unspecified" so there's
no standards reason to retain it anymore. In fact, gettimeofday has
been marked as obsolecent, meaning it could be removed from a future
release of the standard. It is the only interface defined in POSIX
that references these two values. All other references come from the
tzdata database via tzset().
These were used to more faithfully implement early unix ABIs which
have been removed from FreeBSD. NetBSD has completely eliminated
these variables years ago. Linux has migrated to tzdata as well,
though these variables technically still exist for compatibility
with unspecified older programs.
So, there's no real reason to have them these days. They are a
historical vestige that's no longer used in any meaningful way.
Reviewed By: jhb@, brooks@
Differential Revision: https://reviews.freebsd.org/D19550
When a vCPU is HLTed, interrupts with a priority below the processor
priority (PPR) should not resume the vCPU while interrupts at or above
the PPR should. With posted interrupts, bhyve maintains a bitmap of
pending interrupts in PIR descriptor along with a single 'pending'
bit. This bit is checked by a CPU running in guest mode at various
places to determine if it should be checked. In addition, another CPU
can force a CPU in guest mode to check for pending interrupts by
sending an IPI to a special IDT vector reserved for this purpose.
bhyve had a bug in that it would only notify a guest vCPU of an
interrupt (e.g. by sending the special IPI or by resuming it if it was
idle due to HLT) if an interrupt arrived that was higher priority than
PPR and no interrupts were currently pending. This assumed that if
the 'pending' bit was set, any needed notification was already in
progress. However, if the first interrupt sent to a HLTed vCPU was
lower priority than PPR and the second was higher than PPR, the first
interrupt would set 'pending' but not notify the vCPU, and the second
interrupt would not notify the vCPU because 'pending' was already set.
To fix this, track the priority of pending interrupts in a separate
per-vCPU bitmask and notify a vCPU anytime an interrupt arrives that
is above PPR and higher than any previously-received interrupt.
This was found and debugged in the bhyve port to SmartOS maintained by
Joyent. Relevant SmartOS bugs with more background:
https://smartos.org/bugview/OS-6829https://smartos.org/bugview/OS-6930https://smartos.org/bugview/OS-7354
Submitted by: Patrick Mooney <pmooney@pfmooney.com>
Reviewed by: tychon, rgrimes
Obtained from: SmartOS / Joyent
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19299
In all of the architectures we have today, we always use PAGE_SIZE.
While in theory one could define different things, none of the
current architectures do, even the ones that have transitioned from
32-bit to 64-bit like i386 and arm. Some ancient mips binaries on
other systems used 8k instead of 4k, but we don't support running
those and likely never will due to their age and obscurity.
Reviewed by: imp (who also contributed the commit message)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D19280
Skylake Xeons.
See SDM rev. 68 Vol 3 4.6.2 Protection Keys and the description of the
RDPKRU and WRPKRU instructions.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D18893
The pmap_works variable is always true for amd64. Remove it, the
branch in the initialization taken when false, and corresponding
sysctl.
Remove pat_table[] local array, work on pat_index[] directly.
Collapse whole initialization to not override already assigned values.
Add comment explaining the choice for PAT4 and PAT7.
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
MFC note: Leave the sysctl around
Differential revision: https://reviews.freebsd.org/D19225
Some argument validation error paths would return without releasing the
file reference obtained at the beginning of the function.
While here, fix some style bugs and remove trivial debug prints.
Reviewed by: kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19214
With this change, randomization can be enabled for all non-fixed
mappings. It means that the base address for the mapping is selected
with a guaranteed amount of entropy (bits). If the mapping was
requested to be superpage aligned, the randomization honours the
superpage attributes.
Although the value of ASLR is diminshing over time as exploit authors
work out simple ASLR bypass techniques, it elimintates the trivial
exploitation of certain vulnerabilities, at least in theory. This
implementation is relatively small and happens at the correct
architectural level. Also, it is not expected to introduce
regressions in existing cases when turned off (default for now), or
cause any significant maintaince burden.
The randomization is done on a best-effort basis - that is, the
allocator falls back to a first fit strategy if fragmentation prevents
entropy injection. It is trivial to implement a strong mode where
failure to guarantee the requested amount of entropy results in
mapping request failure, but I do not consider that to be usable.
I have not fine-tuned the amount of entropy injected right now. It is
only a quantitive change that will not change the implementation. The
current amount is controlled by aslr_pages_rnd.
To not spoil coalescing optimizations, to reduce the page table
fragmentation inherent to ASLR, and to keep the transient superpage
promotion for the malloced memory, locality clustering is implemented
for anonymous private mappings, which are automatically grouped until
fragmentation kicks in. The initial location for the anon group range
is, of course, randomized. This is controlled by vm.cluster_anon,
enabled by default.
The default mode keeps the sbrk area unpopulated by other mappings,
but this can be turned off, which gives much more breathing bits on
architectures with small address space, such as i386. This is tied
with the question of following an application's hint about the mmap(2)
base address. Testing shows that ignoring the hint does not affect the
function of common applications, but I would expect more demanding
code could break. By default sbrk is preserved and mmap hints are
satisfied, which can be changed by using the
kern.elf{32,64}.aslr.honor_sbrk sysctl.
ASLR is enabled on per-ABI basis, and currently it is only allowed on
FreeBSD native i386 and amd64 (including compat 32bit) ABIs. Support
for additional architectures will be added after further testing.
Both per-process and per-image controls are implemented:
- procctl(2) adds PROC_ASLR_CTL/PROC_ASLR_STATUS;
- NT_FREEBSD_FCTL_ASLR_DISABLE feature control note bit makes it possible
to force ASLR off for the given binary. (A tool to edit the feature
control note is in development.)
Global controls are:
- kern.elf{32,64}.aslr.enable - for non-fixed mappings done by mmap(2);
- kern.elf{32,64}.aslr.pie_enable - for PIE image activation mappings;
- kern.elf{32,64}.aslr.honor_sbrk - allow to use sbrk area for mmap(2);
- vm.cluster_anon - enables anon mapping clustering.
PR: 208580 (exp runs)
Exp-runs done by: antoine
Reviewed by: markj (previous version)
Discussed with: emaste
Tested by: pho
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D5603
The COVERAGE option breaks xtoolchain-gcc GENERIC kernel early boot
extremely badly and hasn't been fixed for the ~week since it was committed.
Please enable for GENERIC only when it doesn't do that.
Related fallout reported by: lwhsu, tuexen (pr 235611)
%r8, %r10, and on non-KPTI configuration %r9 were not restored on fast
return from a syscall.
Reviewed by: markj
Approved by: so
Security: CVE-2019-5595
Sponsored by: The FreeBSD Foundation
MFC after: 0 minutes
This allows userspace to trace the kernel using the coverage sanitizer
found in clang. It will also allow other coverage tools to be built as
modules and attach into the same framework.
Sponsored by: DARPA, AFRL
iflib is already a module, but it is unconditionally compiled into the
kernel. There are drivers which do not need iflib(4), and there are
situations where somebody might not want iflib in kernel because of
using the corresponding driver as module.
Reviewed by: marius
Discussed with: erj
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D19041
This will allow multiple consumers of the coverage data to be compiled
into the kernel together. The only requirement is only one can be
registered at a given point in time, however it is expected they will
only register when the coverage data is needed.
A new kernel conflig option COVERAGE is added. This will allow kcov to
become a module that can be loaded as needed, or compiled into the
kernel.
While here clean up the #include style a little.
Reviewed by: kib
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D18955
For parity with Intel hosts, which already mask out the CPUID feature
bits that indicate the presence of the SPEC_CTRL MSR, do the same on
AMD.
Eventually we may want to have a better support story for guests, but
for now, limit the damage of incorrectly indicating an MSR we do not yet
support.
Eventually, we may want a generic CPUID override system for
administrators, or for minimum supported feature set in heterogenous
environments with failover. That is a much larger scope effort than
this bug fix.
PR: 235010
Reported by: Rys Sommefeldt <rys AT sommefeldt.com>
Sponsored by: Dell EMC Isilon
vmm's CPUID emulation presented Intel topology information to the guest, but
disabled AMD topology information and in some cases passed through garbage.
I.e., CPUID leaves 0x8000_001[de] were passed through to the guest, but
guest CPUs can migrate between host threads, so the information presented
was not consistent. This could easily be observed with 'cpucontrol -i 0xfoo
/dev/cpuctl0'.
Slightly improve this situation by enabling the AMD topology feature flag
and presenting at least the CPUID fields used by FreeBSD itself to probe
topology on more modern AMD64 hardware (Family 15h+). Older stuff is
probably less interesting. I have not been able to empirically confirm it
is sufficient, but it should not regress anything either.
Reviewed by: araujo (previous version)
Relnotes: sure
When building with KCOV enabled the compiler will insert function calls
to probes allowing us to trace the execution of the kernel from userspace.
These probes are on function entry (trace-pc) and on comparison operations
(trace-cmp).
Userspace can enable the use of these probes on a single kernel thread with
an ioctl interface. It can allocate space for the probe with KIOSETBUFSIZE,
then mmap the allocated buffer and enable tracing with KIOENABLE, with the
trace mode being passed in as the int argument. When complete KIODISABLE
is used to disable tracing.
The first item in the buffer is the number of trace event that have
happened. Userspace can write 0 to this to reset the tracing, and is
expected to do so on first use.
The format of the buffer depends on the trace mode. When in PC tracing just
the return address of the probe is stored. Under comparison tracing the
comparison type, the two arguments, and the return address are traced. The
former method uses on entry per trace event, while the later uses 4. As
such they are incompatible so only a single mode may be enabled.
KCOV is expected to help fuzzing the kernel, and while in development has
already found a number of issues. It is required for the syzkaller system
call fuzzer [1]. Other kernel fuzzers could also make use of it, either
with the current interface, or by extending it with new modes.
A man page is currently being worked on and is expected to be committed
soon, however having the code in the kernel now is useful for other
developers to use.
[1] https://github.com/google/syzkaller
Submitted by: Mitchell Horne <mhorne063@gmail.com> (Earlier version)
Reviewed by: kib
Testing by: tuexen
Sponsored by: DARPA, AFRL
Sponsored by: The FreeBSD Foundation (Mitchell Horne)
Differential Revision: https://reviews.freebsd.org/D14599
It is useful for inspecting tlb shootdown hangs. The smp_tlb_generation value
is available using regular ddb data inspection commands.
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
This KPI may in principle be used to create kernel mappings, in which
case we certainly should not be setting PG_U. In any case, PG_U must be
set on all layers in the page tables to grant user mode access, and we
were only setting it on leaf entries. Thus, this change should have no
functional impact.
Reviewed by: kib
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Originally read value is still safely kept. Re-reading code was there
for previous iterations which were partially shared with i386.
Sponsored by: The FreeBSD Foundation
On some architectures, the structures returned by PT_GET*REGS were not
fully populated and could contain uninitialized stack memory. The same
issue existed with the register files in procfs.
Reported by: Thomas Barabosch, Fraunhofer FKIE
Reviewed by: kib
MFC after: 3 days
Security: kernel stack memory disclosure
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18421
See the review for sample test results.
Reviewed by: kib (kernel part)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18401
Handling sizes of > 32 backwards will be updated later.
Reviewed by: kib (kernel part)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18387
For non-ERMS case the code used handle possible trailing bytes with
movsb first and then followed it up with movsq. This also happened
to alter how calculations were done for other cases.
Handle the tail with regular movs, just like when copying forward.
Use leaq to calculate the right offset from the get go, instead of
doing separate add and sub.
This adjusts the offset for non-rep cases so that they can be used
to handle the tail.
The routine is still a work in progress.
Sponsored by: The FreeBSD Foundation
pmap_large_unmap() asserts that an unmapping request covers the
entirety of a 2M or 1G page. The logic in the asserts was out of date
with the loop logic. Correct the test to actually check that
destroying the current superpage mapping does not unmap addresses
beyond those requested by the caller.
Submitted by: D Scott Phillips <d.scott.phillips@intel.com>
Reviewed by: alc
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18345
We zero the whole structure; we don't need to zero the __spare__ field again.
Remove trailing whitespace.
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
Mirror the fix for the native i386 implementation from r218327. This
code is compiled only when the non-default COMPAT_43 option is
configured.
Reported by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Reviewed by: kib
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18298
SDM rev. 068 was released yesterday and it contains the description of
the MSR 0x10a IA32_ARCH_CAP. This change adds symbolic definitions for
all bits present in the document, and decode them in the CPU
identification lines printed on boot.
But also, the document defines SSB_NO as bit 4, while FreeBSD used but
2 to detect the need to work-around Speculative Store Bypass
issue. Change code to use the bit from SDM.
Similarly, the document describes bit 3 as an indicator that L1TF
issue is not present, in particular, no L1D flush is needed on
VMENTRY. We used RDCL_NO to avoid flushing, and again I changed the
code to follow new spec from SDM.
In fact my Apollo Lake machine with latest ucode shows this:
IA32_ARCH_CAPS=0x19<RDCL_NO,SKIP_L1DFL_VME,SSB_NO>
Reviewed by: bwidawsk
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
Differential revision: https://reviews.freebsd.org/D18006
Instead of jumping to locations which store the exact number of bytes,
use displacement to move the destination.
In particular the following clears an area between 8-16 (inclusive)
branch-free:
movq %r10,(%rdi)
movq %r10,-8(%rdi,%rcx)
For instance for rcx of 10 the second line is rdi + 10 - 8 = rdi + 2.
Writing 8 bytes starting at that offset overlaps with 6 bytes written
previously and writes 2 new, giving 10 in total.
Provides a nice win for smaller stores. Other ones are erratic depending
on the microarchitecture.
General idea taken from NetBSD (restricted use of the trick) and bionic
string functions (use for various ranges like in this patch).
Reviewed by: kib (previous version)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17660
Include evdev support and drivers in the amd64 and i386 GENERIC and MINIMAL
kernels. Evdev is used by X and wayland to handle input devices, and this
change, together with upcomming changes in ports will make us handle input
devices better in graphical UIs.
Reviewed by: wulf, bapt, imp
Approved by: imp
Differential Revision: https://reviews.freebsd.org/D17912
We need to know actual value for the standard extended features before
ifuncs are resolved.
Reported and tested by: madpilot
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Both Intel manual and Agner Fog's docs suggest aligning to 16.
See the review for benchmark results.
Reviewed by: kib (previous version)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17661
linux_ioctl_(un)register_handler that allows other driver modules to
register ioctl handlers. The ioctl syscall implementation in each Linux
compat module iterates over the list of handlers and forwards the call to
the appropriate driver. Because the registration functions have the same
name in each module it is not possible for a driver to support both 32 and
64 bit linux compatibility.
Move the list of ioctl handlers to linux_common.ko so it is shared by
both Linux modules and all drivers receive both 32 and 64 bit ioctl calls
with one registration. These ioctl handlers normally forward the call
to the FreeBSD ioctl handler which can handle both 32 and 64 bit.
Keep the special COMPAT_LINUX32 ioctl handlers in linux.ko in a separate
list for now and let the ioctl syscall iterate over that list first.
Later, COMPAT_LINUX32 support can be added to the 64 bit ioctl handlers
via a runtime check for ILP32 like is done for COMPAT_FREEBSD32 and then
this separate list would disappear again. That is a much bigger effort
however and this commit is meant to be MFCable.
This enables linux64 support in x11/nvidia-driver*.
PR: 206711
Reviewed by: kib
MFC after: 3 days
Avoid using DELAY() since it can try to use spin locks on CPUs without
a P-state invariant TSC. For cpu_lock_delay(), always use the TSC if
it exists (even if it is not P-state invariant) to delay for a
microsecond. If the TSC does not exist, read from I/O port 0x84 to
delay instead.
PR: 228768
Reported by: Roger Hammerstein <cheeky.m@live.com>
Reviewed by: kib
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D17851
Replace a call to DELAY(1) with a new cpu_lock_delay() KPI. Currently
cpu_lock_delay() is defined to DELAY(1) on all platforms. However,
platforms with a DELAY() implementation that uses spin locks should
implement a custom cpu_lock_delay() doesn't use locks.
Reviewed by: kib
MFC after: 3 days
Add a new 'debugger_on_trap' knob separate from 'debugger_on_panic'
and make the calls to kdb_trap() in MD fatal trap handlers prior to
calling panic() conditional on this new knob instead of
'debugger_on_panic'. Disable the new knob by default. Developers who
wish to recover from a fatal fault by adjusting saved register state
and retrying the faulting instruction can still do so by enabling the
new knob. However, for the more common case this makes the user
experience for panics due to a fatal fault match the user experience
for other panics, e.g. 'c' in DDB will generate a crash dump and
reboot the system rather than being stuck in an infinite loop of fatal
fault messages and DDB prompts.
Reviewed by: kib, avg
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D17768
On some Intel devices BIOS does not properly reserve memory (called
"stolen memory") for the GPU. If the stolen memory is claimed by the
OS, functions that depend on stolen memory (like frame buffer
compression) can't be used.
A function called pci_early_quirks that is called before the virtual
memory system is started was added. In Linux, this PCI early quirks
function iterates through all PCI slots to check for any device that
require quirks. While this more generic solution is preferable I only
ported the Intel graphics specific parts because I think my
implementation would be too similar to Linux GPL'd solution after
looking at the Linux code too much.
The code regarding Intel graphics stolen memory was ported from
Linux. In the case of Intel graphics stolen memory this
pci_early_quirks will read the stolen memory base and size from north
bridge registers. The values are stored in global variables that is
later read by linuxkpi_gplv2. Linuxkpi stores these values in a
Linux-specific structure that is read by the drm driver.
Relevant linuxkpi code is here:
https://github.com/FreeBSDDesktop/kms-drm/blob/drm-v4.16/linuxkpi/gplv2/src/linux_compat.c#L37
For now, only amd64 arch is suppor ted since that is the only arch
supported by the new drm drivers. I was told that Intel GPUs are
always located on 0:2:0 so these values are hard coded for now.
Note that the structure and early execution of the detection code is
not required in its current form, but we expect that the code will be
added shortly which fixes the potential BIOS bugs by reserving the
stolen range in phys_avail[]. This must be done as early as possible
to avoid conflicts with the potential usage of the memory in kernel.
Submitted by: Johannes Lundberg <johalun0@gmail.com>
Reviewed by: bwidawsk, imp
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D16719
Differential revision: https://reviews.freebsd.org/D17775
The loader tunable 'debug.verbose_sysinit' may be used to toggle verbosity.
This is added to the debugging section of these kernconfs to be turned off
in stable branches for clarity of intent.
MFC after: never
Architectures Software Developer’s Manual Volume 3"). Add the document
to SEE ALSO in bhyve.8 (and pet manlint here a bit).
Reviewed by: jhb, rgrimes, 0mp
Approved by: kib (mentor)
Differential Revision: https://reviews.freebsd.org/D17531
Instead of finding the exact size to fit in we can just shift the target
by -8 + tail. Doing a blind write to a previously rep stosq'ed area comes
with a penalty so do it conditionally.
Sample win on EPYC when zeroing a 257 sized buffer (tail = 1) aligned to
16 bytes:
before: 44782846 ops/s
after: 46118614 ops/s
Idea stolen from NetBSD.
Sponsored by: The FreeBSD Foundation
This driver has been obsolete since the FreeBSD 4.x. It should have
been removed then since the sym(4) driver had subsumed it. The driver
was commented out of GENERIC in 2000.
RelNotes: Yes
stg(4) is marked as gone in 12. Remove it. There are no sightings of
it in the nycbug dmesg database. It was for an obscure SCSI card that
sold mostly in Japan, and was especially popilar among pc98 hackers in
the 4.x time frame. It was also only enabled on i386.
Relnote: Yes
nsp(4) is marked as gone in 12. Remove it. There are no sightings of
it in the nycbug dmesg database. It was for an obscure SCSI card that
sold mostly in Japan, and was especially popilar among pc98 hackers in
the 4.x time frame. It was also only enabled on i386.
Relnote: Yes
ncv(4) is marked as gone in 12. Remove it. There are no sightings of
it in the nycbug dmesg database. It was for an obscure SCSI card that
sold mostly in Japan, and was especially popilar among pc98 hackers in
the 4.x time frame..
Relnote: Yes
We're planning on removing adv, adw, aha, aic, bt, ncv, nsp, and stg
soon. They have been tagged for removal in 12. At least get them out
of GENERIC.
MFC after: 3 days
Relnotes: yes
The knob allows to select the flushing mode or turn it off/on. The
idea, as well as the list of the ignored syscall errors, were taken
from https://www.openwall.com/lists/kernel-hardening/2018/10/11/10 .
I was not able to measure statistically significant difference between
flush enabled vs disabled using syscall_timing getuid.
Reviewed by: bwidawsk
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D17536
When modifying an existing managed mapping, we should find a PV entry
for the old mapping. Verify this.
Before r335784 this would have been implicitly tested by the fact that
we always freed the PV entry for the old mapping.
Reviewed by: alc, kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D17626
This makes the compiler less likely to reload the content from %gs.
The 'P' modifier drops all synteax prefixes and 'n' constraint treats
input as a known at compilation time immediate integer.
Example reloading victim was spinlock_enter.
Stolen from: OpenBSD
Reported by: jtl
Reviewed by: kib
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17615
Apparently AMD machines cannot tolerate this. This was uncovered by
r339386, where cache flush started really flushing the requested range.
Introduce pmap_mapdev_pciecfg(), which simply does not flush cache
comparing with pmap_mapdev(). It assumes that the MCFG region was
never accessed through the cacheable mapping, which is most likely
true for machine to boot at all.
Note that i386 does not need the change, since the architecture
handles access per-page due to the KVA shortage, and page remapping
already does not flush the cache.
Reported and tested by: mjg, Mike Tancsa <mike@sentex.net>
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D17612
The KPI allows to map very large contigous physical memory regions
into KVA, which are not covered by DMAP.
I see both with QEMU and with some real hardware started shipping, the
regions for NVDIMMs might be very far apart from the normal RAM, and
we expect that at least initial users of NVDIMM could install very
large amount of such memory. IMO it is not reasonable to extend DMAP
to cover that far-away regions both because it could overflow existing
4T window for DMAP in KVA, and because it costs in page table pages
allocations, for gap and for possibly unused NV RAM.
Also, KPI provides some special functionality for fast cache flushing
based on the knowledge of the NVRAM mapping use.
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D17070
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
MFC after: 3 days
Differential revision: https://reviews.freebsd.org/D17070
cpu_switch() always reloads the LDT, so this can only affect the
hypervisor process itself. Fix this by explicitly reloading the host
LDT selector after each #VMEXIT. The stock bhyve process on FreeBSD
never uses a custom LDT, so this change is cosmetic.
Reviewed by: kib
Tested by: Mike Tancsa <mike@sentex.net>
Approved by: re (gjb)
MFC after: 2 weeks
Vast majority of syscalls take 6 or less arguments. Move handling of other
cases to a fallback function. Similarly, special casing for _syscall
and __syscall
magic syscalls is moved away.
Return is almost always 0. The change replaces 3 branches with 1 in the common
case. Also the 'frame' variable convinces clang not to reload it on each access.
Reviewed by: kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17542
Finishes the conversion of the 40Gb Intel Ethernet drivers to iflib(9) for
FreeBSD 12.0, and fixes numerous bugs in both ixl(4) and iavf(4).
This commit also re-adds the VF driver to GENERIC since it now compiles and
functions.
The VF driver name was changed from ixlv(4) to iavf(4) because the VF driver is
now intended to be used with future products, not just with Fortville/Fort Park
VFs.
A man page update that documents these drivers is forthcoming in a separate
commit.
Reviewed by: sbruno@, kbowling@
Tested by: jeffrey.e.pieper@intel.com
Approved by: re (gjb@)
Relnotes: yes
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D16429
See r339205 for justification.
Reviewed by: kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17526
The function tweaks CPU capabilities based on the VM platform and
tunables, which affected selection of the cache flush method before
ifuncs were used, and should affect the cache flush in the same way
after ifunc.
PR: 232081
Reported by: phk
Analyzed by: avg
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Apparently CLFLUSH on mmio can cause VM exit, as reported in the PR.
I do not see that anything useful can be done except emulating page
faults on invalid addresses.
Due to the instruction encoding pecularity, also emulate SFENCE.
PR: 232081
Reported by: phk
Reviewed by: araujo, avg, jhb (all: previous version)
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D17482
The reasoning is the same as with the memset change, see r339205
Reviewed by: kib (previous version)
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17441
The change is a no-op for architectures which don't ifunc memset,
memcpy nor memmove.
Convert places which need them. Xen bits by royger.
Reviewed by: kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17487
The VT-x VMCS only stores the base address of the GDTR and IDTR. As a
result, VM exits use a fixed limit of 0xffff for the host GDTR and
IDTR losing the smaller limits set in when the initial GDT is loaded
on each CPU during boot. Explicitly save and restore the full GDTR
and IDTR contents around VM entries and exits to restore the correct
limit.
Similarly, explicitly save and restore the LDT selector. VM exits
always clear the host LDTR as if the LDT was loaded with a NULL
selector and a userspace hypervisor is probably using a NULL selector
anyway, but save and restore the LDT explicitly just to be safe.
PR: 230773
Reported by: John Levon <levon@movementarian.org>
Reviewed by: kib
Tested by: araujo
Approved by: re (rgrimes)
MFC after: 1 week
configuring kernels for i386, amd64, and arm64.
The 'GEOM_PART_GPT' option was added to the DEFAULTS configuration
in r337967.
Approved by: re (kib@)
Reviewed by: ler@
Differential Revision: https://reviews.freebsd.org/D17458
Sponsored by: Netflix, Inc.
rep stos has a high startup time even on modern microarchitectures like
Skylake. Intel optimization manuals discuss how for small sizes it is
beneficial to go for streaming stores. Since those cannot be used without
extra penalty in the kernel I investigated performance impact of just
regular movs.
The patch below implements a very simple scheme: a 32-byte loop followed
by filling in the remainder of at most 31 bytes. It has a 256 breaking
point on which it falls back to rep stos. It provides a significant win
over the current primitive on several machines I tested (both Intel and
AMD). A 64-byte loop did not provide any benefit even for multiple of 64
sizes.
See the review for benchmark data.
Reviewed by: kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17398
This change is a no-op in terms of semantics, but has a side effect
of removing a perfectly useless nop sled for CPUs with ERMS.
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Belatedly add a comment to the amd64 pmap explaining why we initialize
the kernel pmap's resident page count.
Reviewed by: alc, kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17377
Such data may later be unmapped. This occurs, for example, when a
loader-provided microcode update file is discarded.
Reviewed by: alc, kib
Approved by: re (gjb)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17340
For PCID case, there is a dependency between pm_gen zeroing and
reading pm_active for IPI target selection, to ensure that the
invalidation is not missed.
Reported and tested by: mjg
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
The function stopped swapping rdi and rsi, but the error handling
code was not updated with the new register name.
Approved by: re (implicit)
Sponsored by: The FreeBSD Foundation
This reverts part of r333368. The attempt to clear DR6 was occuring
too soon as trapsignal() does not pause to let the debugger notice the
SIGTRAP and query DR6. The signal exchange does not occur until much
later during ast(). As a result, GDB was no longer recognizing
hardware breakpoints and watchpoints on x86.
In addition, any userland programs that want to inspect DR6 in a
SIGTRAP handler don't have a way to do this if we clear DR6 in the
exception handler.
Instead of relying on the kernel to clear DR6, debuggers will have to
explicitly clear it after a trace trap (which they needed to do on
older kernels anyway).
Reviewed by: kib
Approved by: re (delphij)
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D17319
- remove a forward branch in the common case
- replace xchg + lodsb/stosb loop with simple movs
A simple test on Intel(R) Core(TM) i7-4600U CPU @ 2.10GH copying
/foo/bar/baz in a loop goes from 295715863 ops/s to 465807408.
Further changes are pending.
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17281
- move the PSL.AC comment to the fault handler
- stop testing for zero-sized ops. after several minutes of package
building there were no copyin calls with zero bytes and very few
copyout. the semantic of returning 0 in this case is preserved
- shorten exit paths by clearing %eax earlier
- replace xchg with 3 movs. this is what compilers do. a naive
benchmark on EPYC suggests about 1% increase in thoughput thanks to
this change.
- remove the useless movb %cl,%al from copyout. it looks like a
leftover from many years ago
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17286
Both the in-kernel C variant and libc asm variant have very poor performance.
The former compiles to a single byte comparison loop, which breaks down even
for small sizes. The latter uses rep cmpsq/b which turn out to have very poor
throughput and are slower than a hand-coded 32-byte comparison loop.
Depending on size this is about 3-4 times faster than the current routines.
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17328
undefined instruction exception. Previously we would exit the guest,
however an unprivileged user could execute these.
Found with: syzkaller
Reviewed by: araujo, tychon (previous version)
Approved by: re (kib)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D17192
dmaplimit is the first byte after the end of DMAP.
Reported by: "Johnson, Archna" <Archna.Johnson@netapp.com>
Reviewed by: alc, markj
Approved by: re (gjb)
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D17318
For pmap_invalidate_all_pcid(), only reset pm_gen for non-kernel
pmaps, as it was done before the conversion to ifuncs. The reset is
useless but innocent for kernel_pmap. Coverity reported that cpuid is
used uninitialized in this case.
Reported by: cem
Reviewed by: alc, cem, markj
CID: 1395807
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Differential revision: https://reviews.freebsd.org/D17314
Split calculation of mask for shootdown IPI and local
invalidation. Reorder IPI before local.
Suggested by: alc
Reviewed by: alc, markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
Approved by: re (rgrimes)
Differential revision: https://reviews.freebsd.org/D17277
- _fault handlers for both primitives are identical, provide just one
- change the copying scheme to match memcpy (in particular jump
avoidance for the most common case of multiply of 8)
- stop re-reading pcb address on exit, just store it locally (in r9)
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17265
If the size is 15 bytes or less avoid spinning up rep just to copy the 8
bytes. In my tests on EPYC and old Intel microarchs without ERMS (like
Westmere) it provided a nice win over the current version (e.g. for EPYC
memset with 15 bytes of size goes from 59712651 ops/s to 70600095) all
while almost not pessimizing the other cases.
Data collected during package building shows that < 16 sizes are pretty
common.
Verified with the glibc test suite.
Approved by: re (kib)
Fix a fat-fingered typo with a "funny" side-effect: when doing copyin on a
cpu without ERMS and with size being a multiply of 8 a page fault would be
triggered resulting in EFAULT.
Pointy hat: mjg
Approved by: re (implicit)
A lot of function have the following check:
cmpq %rax,%rdi /* verify address is valid */
ja fusufault
The label is present earlier in kernel .text, which means this is a jump
backwards. Absent any information in branch predictor, the cpu predicts it
as taken. Since it is almost never taken in practice, this results in a
completely avoidable misprediction.
Move it past all consumers, so that it is predicted as not taken.
Approved by: re (kib)
This simplifies the runtime logic and reduces the number of
runtime-constant branches.
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Differential revision: https://reviews.freebsd.org/D16736
pm_pcid is unsigned.
Reviewed by: cem, markj
CID: 1395727
Noted by: cem
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
MFC after: 3 days
Differential revision: https://reviews.freebsd.org/D17235
Patch removes all checks for pti/pcid/invpcid from the context switch
path. I verified this by looking at the generated code, compiling with
the in-tree clang. The invpcid_works1 trick required inline attribute
for pmap_activate_sw_pcid_pti() to work.
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Differential revision: https://reviews.freebsd.org/D17181
There is no need to use %rax for temporary values and avoiding doing
so shortens the func.
Handle the explicit 'check for tail' depessimisization for backwards copying.
This reduces the diff against userspace.
Tested with the glibc test suite.
Approved by: re (kib)
This will be used in following conversion of pmap_activate_sw().
Reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Differential revision: https://reviews.freebsd.org/D17181
There is a braino in the non-erms variant which breaks the
functionality.
Will be fixed at a later time with a different patch.
Reported by: Manfred Antar
Approved by: re (implicit)
There is no need to use %rax for temporary values and avoiding doing
so shortens the func.
Handle the explicit 'check for tail' depessimisization for backwards copying.
This reduces the diff against userspace.
Approved by: re (kib)
Intel docs claim such a memset (rep stosb + 4096 bytes) is
special-cased by microarchs. They also switched Linux to use
it for this purpose.
Approved by: re (gjb)
The stac/clac combo around each byte copy is causing a measurable
slowdown in benchmarks. Do it only before and after all data is
copied. While here reorder the code to avoid a forward branch in
the common case.
Note the copying loop (originating from copyinstr) is avoidably slow
and will be fixed later.
Reviewed by: kib
Approved by: re (gjb)
Differential Revision: https://reviews.freebsd.org/D17063
Also this fixes the eflags.ac leak from copyin_smap() when the copied
data length is multiple of eight bytes.
Sponsored by: The FreeBSD Foundation
Approved by: re (gjb)
Non-PTI mode does not switch kcr3, which means that kcr3 is almost
always stale. This is important for the NMI handler, which reloads
%cr3 with PCPU(kcr3) if the value is different from PMAP_NO_CR3.
The end result is that curpmap in NMI handler does not match the page
table loaded into hardware. The manifestation was copyin(9) looping
forever when a usermode access page fault cannot be resolved by
vm_fault() updating a different page table.
Reported by: mmacy
Reviewed by: markj
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
Approved by: re (gjb)
This appeared to be required to have EFI RT support and EFI RTC
enabled by default, because there are too many reports of faulting
calls on many different machines. The knob is added to leave the
exceptions unhandled to allow to debug the actual bugs.
Reviewed by: kevans
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (rgrimes)
Differential revision: https://reviews.freebsd.org/D16972
handling.
This is split into a separate commit from the main change to make it
easier to handle possible revert after upcoming KBI freeze.
Reviewed by: kevans
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Approved by: re (rgrimes)
Differential revision: https://reviews.freebsd.org/D16972
