Note that this required adding missing ()'s around the outermost level
of MSK_READ_MIB*. Otherwise, the void cast was only applied to the
first register read. This also meant that MSK_READ_MIB64 was pretty
broken as the uint64_t cast only applied to the first 16-bit register
read in each MSK_READ_MIB32 invocation and the 32-bit shift was only
applied to the second register read of the pair.
Reviewed by: imp, emaste
Reported by: GCC -Wunused-value
Differential Revision: https://reviews.freebsd.org/D36777
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
One more instance of if_input being called outside of
interrupt, by means of msk_handle_events.
Differential Revision: https://reviews.freebsd.org/D23379
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
in Marvell terms) to 32768. 32768 looks overkill but it will
ensure correct DMAed update. This change addresses occasional
watchdog timeouts reported on 10.2-RELEASE.
Tested by: Johann Hugo <jhugo@meraka.csir.co.za>
MFC after: 2 weeks
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
out 32 is not enough to support a full sized TSO packet.
While I'm here fix a long standing bug introduced in r169632 in
bce(4) where it didn't include L2 header length of TSO packet in
the maximum DMA segment size calculation.
In collaboration with: rmacklem
MFC after: 2 weeks
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
the actual PCI device which makes the request for DMA tag, instead of
some descendant of the PCI device, by creating a pass-through trampoline.
- Sprinkle const on tables.
- Use NULL instead of 0 for pointers.
- Take advantage of nitems().
MFC after: 1 week
and voltage sensor, TWSI is used to get sensor data. msk(4) does
not monitor these sensors and interrupt for TWSI completion is
disabled by default.
However, due to unknown reason, the TWSI completion interrupt fires
and it resulted in interrupt storm. To fix it, acknowledges the
TWSI completion interrupt if driver see the event. Given that not
all Yukon II controllers show the issue it could be a silicon bug
which does not honor interrupt masking.
Probably the right way to address the issue is disabling automatic
TWSI cycle initiation against these sensors. It would be even
better to implement reading voltage/temperature from the NIC but it
requires access to National LM80 through TWSI and documentation to
do that is not available yet(probably will never happen).
Reported by: jhb
Tested by: jhb
MFC after: 2 weeks
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
Unnecessarily complex LE format used on Marvell controller was
main reason not to enable 64bit DMA addressing in driver. If high
32bit address of DMA address of TX/RX buffer is changed, driver has
to generate a new LE. In TX path, driver will keep track of lastly
used high 32bit address of DMA address and generate a new LE
whenever it sees high address change in the DMA address. In RX path,
driver will always use two LEs to specify 64bit DMA address of RX
buffer. If the high 32bit address of DMA address of RX buffer is
the same as previous DMA address of RX buffer, driver does not have
to use two LEs but driver will use two LEs for simplicity in RX
ring management.
One of draw back for switching to 64bit DMA addressing is that the
large amount of LEs are used to specify 64bit DMA address such that
number of available LEs for TX/RX buffers are considerably reduced.
To mitigate the issue, increase number of available LEs from 256 to
384 for TX and from 256 to 512 for RX. For 32bit architectures,
msk(4) does not use 64bit DMA addressing to save resources.
Tested by: das
Because driver is accessing a common MII structure in
mii_pollstat(), updating user supplied structure should be done
before dropping a driver lock.
Reported by: Karim (fodillemlinkarimi <> gmail dot com)
bits of the register is used for other purposes such that clearing
these bits resulted in unexpected results such as corrupted RX
frames or missing LE status updates. For old controllers like
Yukon EC it had no effect but it caused all kind of troubles on
Yukon Supreme.
This change shall improve stability of controllers like Yukon
Ultra, Ultra2, Extreme, Optima and Supreme.
After controller updates control word in a RX LE, driver converts
it to host byte order. The checksum value in the control word is
stored in big endian form by controller. r205091 didn't account for
the host byte order conversion such that the checksum value was
incorrectly interpreted on big endian architectures which in turn
made all TCP/UDP frames dropped. Make RX checksum offload work
on any architectures by swapping the checksum value.
Reported by: Sreekanth M. ( kanthms <> netlogicmicro dot com )
Tested by: Sreekanth M. ( kanthms <> netlogicmicro dot com )